Harman Kardon ONYX STUDIO Service Manual ▷ View online
Harman Kardon Onyx Studio
Assembly procedure
2. ASSEMBLY INSTRUCTION 裝說明
1. 取藍牙小板 BT Antenna, 使用鑷子,撕除
藍牙小板離型紙,把藍牙小板貼入前殼對
應位置(
注意:藍牙天線需壓緊
)
Tears off linear of adhesive from BT Antenna
Assy and stick on the front cover by pressing as
shown in the figure.
Assy and stick on the front cover by pressing as
shown in the figure.
Note: Please use the pressing fixture for this
assembly.
assembly.
注意:密封圈勿折疊, 密封圈勿脫出
Attention: Do not bent the rubber ring and let it
out of the gap.
Attention: Do not bent the rubber ring and let it
out of the gap.
2.1 把 Front Radiator 裝在前殼對應位置(Front
Radiator 安裝位置有防呆設計)
Radiator 安裝位置有防呆設計)
2.2 使用螺絲起子,依次鎖付 4PCs 螺絲
(3*10.2MM)
(3*10.2MM)
藍牙天線貼付于兩螺柱
中間位置
密封圈折疊
密封圈脫出
2
1
3
4
Harman Kardon Onyx Studio
Assembly procedure
注意:Front Radiator 不可壓到藍牙天線
Assemble the Front Radiator to the front cover.
Note: Do not press the BT
Antenna Assy shown
as in the figure.
Tightens 4 screws by using the T10 screwdriver.
3. 放置 Woofer 在前殼對應位置
注意:Mid Woofer“接頭”朝面框外側位置
Place the Woofer fix on the front cover.
注意:Mid Woofer“接頭”朝面框外側位置
Place the Woofer fix on the front cover.
Note: Let the connector of Mid Woofer outward
shown as in the figure.
shown as in the figure.
3.1 使用螺絲起子,依次鎖付 Mid Woofer 4PCs
螺絲(3*14.2MM)
Tightens 4 screws by using the T10 screwdriver.
螺絲(3*14.2MM)
Tightens 4 screws by using the T10 screwdriver.
3.2 注意: Mid woofer 正面鼓膜不可觸碰、撞
傷
傷
Note: Do not damage and touch the Mid woofer
4. 放置 Mid Woofer 在前殼對應位置
注意:Mid Woofer“接頭”朝面框外側位置
Place the Woofer fix on the front cover.
注意:Mid Woofer“接頭”朝面框外側位置
Place the Woofer fix on the front cover.
Note: Let the connector of Mid Woofer outward
shown as the figure
shown as the figure
Mid Woofer
膠圈
1
2
3
4
1
2
Harman Kardon Onyx Studio
Assembly procedure
4.1 使用螺絲起子,依次鎖付 Mid Woofer 4PCs
螺絲(3*14.2MM)
Tightens 4 screws by using the T10 screwdriver.
螺絲(3*14.2MM)
Tightens 4 screws by using the T10 screwdriver.
4.2 注意: Mid woofer 正面鼓膜不可觸碰、撞
傷
傷
Note: Do not damage and touch the Mid woofer
5. 撕除 Gasket 離型紙,貼付在 Soft Dome
Tweeter 背面磁鐵上,居中貼付;
注意:Soft Dome Tweeter“耳朵”對準缺口處
Tears off linear of adhesive from gasket and stick
on the back of Soft Dome Tweeter.
Tweeter 背面磁鐵上,居中貼付;
注意:Soft Dome Tweeter“耳朵”對準缺口處
Tears off linear of adhesive from gasket and stick
on the back of Soft Dome Tweeter.
6. 取 Speaker Plate 裝在 Soft Dome Tweeter 上
,使用螺絲起子,依次鎖付 4PCs 螺絲
(3*10.2MM)
注意:Speaker Plate 小孔為定位孔,大孔為螺
絲孔
Assemble Speaker Plate on the Soft Dome
Tweeter and tightens 4 screws by using the T10
screwdriver.
,使用螺絲起子,依次鎖付 4PCs 螺絲
(3*10.2MM)
注意:Speaker Plate 小孔為定位孔,大孔為螺
絲孔
Assemble Speaker Plate on the Soft Dome
Tweeter and tightens 4 screws by using the T10
screwdriver.
Mid Woofer
膠圈
2
1
3
4
1
2
3
4
Soft Dome Tweeter“耳朵”對準缺口處
Harman Kardon Onyx Studio
Assembly procedure
7. 把 Tweeter Cable-long 和 Tweeter
Cable-short 連接到對應的 Tweeter 上
Connect the Tweeter Cable-long and Tweeter
Cable-short to the Tweeter shown in the figure.
Cable-short 連接到對應的 Tweeter 上
Connect the Tweeter Cable-long and Tweeter
Cable-short to the Tweeter shown in the figure.
注意:
Tweeter Cable-long 和 Tweeter
Cable-short 不可接錯,不可接反;紅色 Tweeter
Cable 對應 Tweeter 紅色打點標示端,黑色
Tweeter Cable 對應另一端
Cable 對應 Tweeter 紅色打點標示端,黑色
Tweeter Cable 對應另一端
Note: Be carefully the direction of Tweeter
Cable-long and Tweeter Cable-short.
Cable-long and Tweeter Cable-short.
8. 取電烙鐵及無鉛錫絲焊接固定 Tweeter
Cable-long;完成后,焊接固定 Tweeter
Cable-short
Cable-long;完成后,焊接固定 Tweeter
Cable-short
注意:烙鐵接觸接口時間不能超過 5s,防止
接口脫落
注意:焊接處需圓滑飽滿,連接牢固
接口脫落
注意:焊接處需圓滑飽滿,連接牢固
Tweeter Cable-long
Tweeter Cable-short
Click on the first or last page to see other ONYX STUDIO service manuals if exist.