DOWNLOAD Harman Kardon HS 1000 (serv.man3) Service Manual ↓ Size: 4.22 MB | Pages: 72 in PDF or view online for FREE

 

Report No. SH09021130-001 

Page 52 of 71 

 

15.2 Block Diagram of Test Setup 
 
 

 
 
15.2 .1Test Setup and Test Procedure 
 

 

The EUT was placed on a 0.8m high wooded table, standing on the ground reference  
plane 2.6m by 1.8m in size, made by aluminium 0.5mm thick. 
 
The distance between the EUT and any other of the metallic surface except the GRP is  
greater than 0.5m. 
 
The main lead excess than 1m is gathered into a flat coil with a 0.4m diameter and situated  
at a distance of 0.1m above the ground reference plane to insure the distance between the  
coupling device and the EUT were 1m or less. 
 
The EUT was arranged and connected to satisfy its functional requirement and supplied by  
The coupling-decoupling network (Best EMC). 

 
 

 

The EUT was placed on a 0.1m high wooden support, standing on the ground reference 
plane 2.6m by 1.8m, made by aluminium 0.5mm thick. 
 
The distance between the EUT and any other of the metallic surface except the GRP is  
greater than 0.5m. 
 
The main lead excess than 1m is gathered into a flat coil with a 0.4m diameter and situated  
at a distance of 0.1m above the ground reference plane to insure the distance between the  
coupling device and the EUT were 1m or less. 
 
The EUT was arranged and connected to satisfy its functional requirement and supplied by  
The coupling-decoupling network (Best EMC). 

 

 
     

GRP 

 

Report No. SH09021130-001 

Page 53 of 71 

 

 
 
 
15.3 Test Protocol 
 

Temperature  : 

23

°C  

Relative Humidity: 

34% 

 

Test No. 

# 

Level 

[kV] 

Polarity 

+/- 

Line for test 

Pass/ 

Fail 

Comment 

1 1 +/- L P   

2 1 +/- N P   

3 1 +/- 

PE 

NA  

4 1 +/- 

L-N 

P   

5 1 +/- 

L-PE 

NA  

6 1 +/- 

N-PE 

NA  

7 1 +/- 

L,N.PE 

NA  

8 0.5 +/- DC -   

9 0.5 +/- I/O -   

 
 
 

 
 
15.4 Additions, Deviations and Exclusions from Standards 
 
 

None. 

 

Report No. SH09021130-001 

Page 54 of 71 

 
16.1 Severity Level and Performance Criterion 

16.1.1 Test level 

 

Level 

Test field strength V/m 

 

1 

 

1 

2 

 

3 

3 

 

10 

 

X 

Special 

 
Note: 1. X is an open test level, this level may be given in the product specification. 
          2. The gray row is the selected test level. 

 

16.1.2 Performance Criterion   

 

   Performance 

criterion 

 

 

Report No. SH09021130-001 

Page 55 of 71 

16.2 Block diagram of test setup 
 

 
 
16.3 Test Setup and Test Procedure 
 

16.3.1 Test setup 

 

 

The test was conducted in an anechoic chamber which is 7m in length, 5m in width and 3m in 

height   to  maintain a uniform field of sufficient dimensions with respect to the EUT, and also in 
order to  comply with various national and international laws prohibiting interference to radio 
communications. 

  

 

 

For the table top EUT, the equipment is placed in the test facility on a non-conducting table 

0.8m high. 
 

For the floor standing EUT, the equipment is placed in the test facility on a non-conducting 

support 0.1m high. 
 

The EUT was placed on the uniform calibrated plane which is 3V/m EM field. 

 
 

Unshielded parallel wire was used during the test. 

 

 

 

Wire is left exposed to the electromagnetic field for a distance of 1m form the EUT. 

Power 

Antenn
a mask

   
       Table 

amplifier 

Signal 

EUT 

Field probe 

Field 

Optical 

Filte