DOWNLOAD Harman Kardon HKTS 8 (serv.man8) Service Manual ↓ Size: 611.98 KB | Pages: 16 in PDF or view online for FREE

TROUBLESHOOTING 13

• Check that receiver/amplifier is on and a source is playing.

• Check that the powered subwoofer is plugged in, its Power switch

 is switched on to 

the “ON•” position.

• Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires 

are connected. Make sure none of the speaker wires are frayed, cut or punctured.

• Review proper operation of your receiver/amplifier.

• Check the “Balance” control on your receiver/amplifier.

• Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are 

connected. Make sure none of the speaker wires are frayed, cut or punctured.

• In Dolby Digital or DTS

®

modes, make sure that the receiver/processor is configured so that the 

speaker in question is enabled.

• Check all wires and connections between receiver/amplifier and speaker.

Make sure all wires are connected. Make sure none of the speaker wires are frayed,
cut or punctured.

• If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not 

in phantom mode.

• If your receiver/processor is set in Dolby Digital or DTS

®

mode, make sure the receiver/processor 

is con-figured so that the center speaker is enabled.

• Check all wires and connections between receiver/ amplifier and speakers.

Make sure all wires are connected.

Make sure none of the speaker wires are frayed, cut or punctured.

• If more than one pair of main speakers is being used, check the minimum impedance 

requirements of your receiver/amplifier.

• Make sure the connections to the left and right “Speaker Inputs” have the correct polarity (+ and –).

• Make sure the subwoofer is plugged into an active electrical outlet.
• Make sure the powered subwoofer is plugged in and switched on.
• In Dolby Digital or DTS

®

modes, make sure your receiver/processor is 

configured so that the subwoofer and LFE output are enabled.

• Check all wires and connections between receiver/ amplifier and speakers.

Make sure all wires are connected. Make sure none of the speaker wires are frayed,

cut or punctured.

• Review proper operation of your receiver/amplifier and its surround-sound features.
• Make sure the movie or TV show you are watching is recorded in a surround-sound mode.

If it is not, check to see if your receiver/ amplifier has other surround modes you may use.

• In Dolby Digital or DTS

®

modes, make sure your receiver/processor is configured so that the 

surround speakers are enabled.

• Review the operation of your DVD player and the jacket of your DVD to make sure that the 

DVD features the desired Dolby Digital or DTS

®

mode, and that you have properly selected that 

mode using both the DVD player’s menu and the DVD disc’s menu.

14 SPECIFICATIONS

Frequency Response
35Hz – 20kHz (–6dB)

Recommended Power 
10 – 80 Watts 

Impedance
8 Ohms nominal 

Sensitivity
86dB @ 1 Watt/1 meter

Tweeter
One 1/2" dome, video-shielded

Midrange
One 3" driver, video-shielded

Dimensions (H x W x D) 
167mm x 100mm x 92mm

Weight 
0.6kg 

Recommended Power 
10 – 80 Watts 

Impedance
8 Ohms nominal 

Sensitivity
86dB @ 1 Watt/1 meter

Tweeter
One 3/4" dome, video-shielded

Midrange
Dual 3" drivers, video-shielded

Dimensions (H x W x D) 
102mm x 241mm x 92mm

Weight 
1kg 

Amplifier 
100 Watts RMS

Bass
10" Woofer, bass-reflex enclosure

Dimensions (H x W x D) 
479mm x 340mm x 340mm

Weight 
15kg 

All features and specifications are subject to change without notice.

Harman Kardon and Power for the Digital Revolution are registered trademarks 
of Harman International Industries, Incorporated.

* Trademarks of Dolby Laboratories.

DTS is a registered trademark of Digital Theater Systems, Inc.

250 Crossways Park Drive, Woodbury, New York 11797 
www.harmankardon.com
Harman Consumer Group International
2, Route de Tours, 72500 Château-du-Loir, France
© 2005 Harman Kardon, Incorporated 
Part no.: 406-000-05150