Harman Kardon HKTS 60 Service Manual ▷ View online
HKTS 60BQ/230
12
OM-CT-315/316 / ( 0248CSK - 13/Oct/2010 )
Operation
Operation
Turning the Subwoofer On and Off
Set the HKTS 210SUB’s
Power Switch 8 to the ON position.
If the
•
Power On Mode Switch 2 is set to AUTO, the HKTS 210SUB will
automatically turn itself on when it receives an audio signal, and it will go into
the standby mode after it has received no audio signal for 15 minutes. The
HKTS 210SUB’s leD will glow white when the subwoofer is on and will not be
illuminated when the subwoofer is in standby.
If the
If the
•
Power On Mode Switch 2 is set to On, the HKTS 210SUB will remain on
at all times. The HKTS 210SUB’s leD will glow white.
If the
If the
•
External Trigger Input 5 is connected to a trigger-voltage source, the
HKTS 210SUB will turn on whenever a trigger voltage is present and will enter the
standby mode after the trigger voltage ceases, regardless of the position of the
Power On Mode Switch 2.
If you will be away from home for an extended period of time, or if you will not be
using the subwoofer for an extended period, switch the
Power Switch 8 to the OFF
Position.
Subwoofer Adjustments: Volume
Use the
Subwoofer Level Control 3 to set the HKTS 210SUB’s volume. Turn the
knob clockwise to increase the subwoofer’s volume; turn the knob counterclockwise to
decrease the subwoofer’s volume.
Subwoofer Adjustments: Phase
The
Phase Switch 0 determines whether the HKTS 210SUB’s piston-like action moves
in and out in phase with the satellite speakers. If the subwoofer were to play out of
phase with the satellite speakers, the sound waves from the satellites could cancel out
sound waves from the subwoofer, reducing bass performance and sonic impact. This
phenomenon depends in part on the placement of all the speakers in the room.
Although in most cases the
Although in most cases the
Phase Switch 0 should be left in the NORMAL position,
there is no absolutely correct setting for the
Phase Switch 0. When the HKTS 210SUB
is properly in phase with the satellite speakers, the audio will be clearer, have maximum
impact and make percussive sounds like drums, piano and plucked strings sound more
lifelike. The best way to set the
Phase Switch 0 is to listen to music that you know
well and set the switch in the position that gives drums and other percussive sounds
maximum impact.
Subwoofer Adjustments: Bass Boost
When set to the ON position, the Bass Boost Switch 1 enhances low-frequency
performance, resulting in bass with more impact, which you may prefer while watching
movies or listening to music. There is no harm in experimenting with this control. Setting
the switch to the OFF position will return normal low-frequency performance.
harman/kardon
HKTS 20/30/60 -230V Service Manual
Page 33 of 46
13
HKTS 60BQ/230
ENGLISH
Troubleshooting
Troubleshooting
This unit is designed for trouble-free operation. Most problems that users encounter are due to operating errors. So if you have a problem, first check this list for a possible solution. If
the problem persists, consult your authorized harman kardon service centre.
Problem
Solution
If there is no sound from any of the speakers:
Check that the receiver/amplifier is on and a source is playing.
•
Make sure that all wires and connections between the receiver/amplifier and the speakers are
•
connected properly.
Make sure none of the speaker wires is frayed, cut or punctured.
Make sure none of the speaker wires is frayed, cut or punctured.
•
Review the proper operation of your receiver/amplifier.
•
If there is no sound coming from one speaker:
Check that the balance control on your receiver/amplifier is not set all the way to one channel.
•
Check your receiver/amplifier’s speaker setup procedure to make sure that he speaker in
•
question has been enabled and its volume level has not been turned all the way down.
Make sure that all wires and connections between the receiver/amplifier and the speaker are
Make sure that all wires and connections between the receiver/amplifier and the speaker are
•
connected properly.
Make sure the speaker wires are not frayed, cut or punctured.
Make sure the speaker wires are not frayed, cut or punctured.
•
If there is no sound coming from the center speaker:
Check your receiver/amplifier’s speaker setup procedure to make sure that the center speaker
•
has been enabled and its volume level has not been turned all the way down.
Make sure that all wires and connections between the receiver/amplifier and the center speaker
Make sure that all wires and connections between the receiver/amplifier and the center speaker
•
are connected properly.
Make sure the speaker wires are not frayed, cut or punctured.
Make sure the speaker wires are not frayed, cut or punctured.
•
If your receiver is operating in Dolby
•
®
Pro logic
®
mode, make sure that the center speaker is not
set to Phantom.
you can find additional troubleshooting information in the FAQs link on the Support page at www.harmankardon.com.
harman/kardon
HKTS 20/30/60 -230V Service Manual
Page 34 of 46
HKTS 60BQ/230
14
OM-CT-315/316 / ( 0248CSK - 13/Oct/2010 )
Specifications
Specifications
HKTS 60BQ/230 System
Frequency Response
45Hz – 20kHz (-6dB)
HKTS 210SUB Subwoofer
Power requirement
AC 100–120v, 50/60 Hz, 200W (USA)
AC 220–240v, 50/60 Hz, 200W (eU)
Amplifier Power
200 watts RMS
Woofer
8" (200mm) woofer, sealed enclosure
external Trigger Input voltage
3 ~ 30 volts AC/DC
Dimensions (H x W x D)
353mm x 267mm x 267mm
(13-29/32" x 10-1/2" x 10-1/2")
(13-29/32" x 10-1/2" x 10-1/2")
Weight
9.0 kg (19.8 lb)
SAT-TS60 Satellites
Recommended Power
20 ~ 150 watts
Impedance
8 ohms nominal
Sensitivity
83dB @ 2.83v/1 meter
Tweeter
One 1" (25mm) CMMD lite dome, video-shielded
Midrange
Dual 3" (75mm) flat-diaphragm drivers, video-shielded
Dimensions – including stands
(H x W x D)
(H x W x D)
299mm x 110mm x 88mm
(11-25/32" x 4-11/32"x 3-15/32")
(11-25/32" x 4-11/32"x 3-15/32")
Weight
1.5 kg (3.4 lb)
CEN-TS60
Recommended Power
20 ~ 150 watts
Impedance
8 ohms nominal
Sensitivity
83dB @ 2.83v/1 meter
Tweeter
One 1" (25mm) CMMD lite dome, video-shielded
Midrange
Dual 3" (75mm) flat-diaphragm drivers, video-shielded
Dimensions (H x W x D)
110mm x 272mm x 88mm
(4-11/32" x 10-11/32" x 3-15/32" )
(4-11/32" x 10-11/32" x 3-15/32" )
Weight
1.5kg (3.3 lb)
harman/kardon
HKTS 20/30/60 -230V Service Manual
Page 35 of 46
harman/kardon
HKTS 20/30/60 -230V Service Manual
Page 36 of 46
Click on the first or last page to see other HKTS 60 service manuals if exist.