Harman Kardon HK 3490 (serv.man2) EMC - CB Certificate ▷ View online
- Page 11 of 45 -
Report
No.
98503
8.15
No risk of damage to the insulation of internal
wiring due to hot parts or sharp edges
wiring due to hot parts or sharp edges
Wires safely anchored
away from parts with high
temperature.
away from parts with high
temperature.
P
8.16
Only special supply equipment can be used
Not supplied by a special
supply apparatus.
supply apparatus.
N/A
8.17
Insulated winding wire without additional
interleaved insulation
interleaved insulation
No such winding wire.
N/A
8.18
Endurance test as required by 8.17
N/A
8.19
Disconnection from the mains
See below
P
8.19.1 Disconnect
device
Mains plug is used as
disconnect devices.
disconnect devices.
P
All-pole switch or circuit breaker with >3mm
contact separation
contact separation
No all-pole mains switch
or circuit breaker.
or circuit breaker.
N/A
8.19.2
Mains switch ON indication
Indicator lamp or
FL display lit-on
FL display lit-on
P
8.20
Switch not fitted in the mains cord
P
8.21
Bridging components comply with clause 14
Yes, mains switch and relay
across the capacitor is
certified component
See appended table, list of
critical components.
across the capacitor is
certified component
See appended table, list of
critical components.
P
8.22
Non-separable thin sheet material
No non-separable thin
sheet material.
sheet material.
N/A
9
ELECTRIC SHOCK HAZARD UNDER NORMAL OPERATING CONDITIONS
9.1
Testing on the outside
P
9.1.1
For voltages >1000 V ac or >1500 V dc complies
with clause 13.3.1 for basic insulation
with clause 13.3.1 for basic insulation
No voltages exceeding
1000V AC or 1500V DC.
1000V AC or 1500V DC.
N/A
9.1.1.1
a) Open circuit voltages
Mains input voltage > 35V,
see below.
see below.
—
b) Touch current measured from terminal devices
using the network in annex D ............................. :
using the network in annex D ............................. :
See attachment, Table to
EN/IEC 60065 7
EN/IEC 60065 7
th
edition.
P
c) Discharge not exceeding 45 μC
No part or contact of a
terminal with stored voltage
s between 60V - 15 kV.
terminal with stored voltage
s between 60V - 15 kV.
N/A
- Page 12 of 45 -
Report
No.
98503
d) Energy of discharge not exceeding 350 mJ
No part or contact of
a terminal with stored
voltages exceeding 15kV
a terminal with stored
voltages exceeding 15kV
N/A
9.1.1.2
Test with test finger and test probe
No access to hazardous
live parts
live parts
P
9.1.2
No hazardous live shafts of knobs, handles or
levers
levers
No live shaft, handles or
levers
levers
N/A
9.1.3
Ventilation holes and other holes tested by means
of 4 mm x 100 mm test pin
of 4 mm x 100 mm test pin
No access for the test pin
P
9.1.4
Terminal devices tested with 1 mm x 20 mm test
pin (10 N); test probe D of IEC 61032
pin (10 N); test probe D of IEC 61032
Does not reach hazardous
live parts
live parts
P
Terminal devices tested with 1 mm x 100 mm
straight wire (1 N); test probe D of IEC 61032
straight wire (1 N); test probe D of IEC 61032
Does not reach hazardous
live parts
live parts
P
9.1.5
Pre-set controls tested with 2.5 mm x 100 mm test
pin (10 N); test probe C of IEC 61032
pin (10 N); test probe C of IEC 61032
No preset controls
N/A
9.1.6
No shock hazard due to stored charge on
withdrawal of the mains plug; voltage (V) after 2 s
................................................................................. :
withdrawal of the mains plug; voltage (V) after 2 s
................................................................................. :
Measured voltage after
2 sec: Max. 1 V (peak).
2 sec: Max. 1 V (peak).
P
If C is not greater than 0,1 μF no test needed
N/A
9.1.7
a) Enclosure sufficiently resistant to external force
P
Test probe 11 of IEC 61032 for 10 s (50 N)
Test with test finger result
in no hazard
in no hazard
P
b) Test hook of fig. 4 for 10 s (20 N)
Test with test hook results
in no hazard.
in no hazard.
P
c) 30 mm diameter test tool for 5 s (100 or 250 N) :
Tested with 100N results
in no damage.
in no damage.
P
9.2
No hazard after removing a cover by hand
No cover removable by
hand
hand
N/A
- Page 13 of 45 -
Report
No.
98503
10 INSULATION
REQUIREMENTS
10.1
Insulation resistance (MΩ) at least 2 MΩ min. after
surge test for basic and 4 MΩ min. for reinforced
insulation ............................................................... :
surge test for basic and 4 MΩ min. for reinforced
insulation ............................................................... :
> 100 M
Ω, after surge test
P
10.2 Humidity
treatment 48 h or 120 h ....................... :
120 h (40
°C).
No impairment
P
10.3
Insulation resistance and dielectric strength
between mains teminals
between mains teminals
See appended table
P
Insulation Resistance and dielectric strength
across BASIC or SUPPLEMENTARY insulation
(Class 1)
across BASIC or SUPPLEMENTARY insulation
(Class 1)
Class II apparatus.
N/A
Insulation resistance and dielectric strength
across REINFORCED insulation (Class II)
across REINFORCED insulation (Class II)
See appended table
P
11 FAULT
CONDITIONS
11.1
No shock hazard under fault condition
No electric shock hazard
under fault conditions.
under fault conditions.
P
11.2
Heating under fault condition
See appended table
P
No hazard from softening solder
No softening of solder
P
Flames extinguish within 10 seconds
No flames
P
Soldered terminations not used as protective
mechanism
mechanism
No protective mechanism
P
11.2.1
Measurement of temperature rises
See appended table
P
11.2.2
Temperature rise of accessible parts
See appended table
P
11.2.3
Temperature rise of parts, other than windings,
providing electrical insulation
providing electrical insulation
See appended table
P
Temperature rise of printed circuit boards (PCB)
exceeding the limits of table 3 by max. 100 K for
max. 5 min
exceeding the limits of table 3 by max. 100 K for
max. 5 min
No exceeding the limits of
Table 3.
Table 3.
P
a) Temperature rise of printed circuit boards
(PCB) to 20.1.3, exceeding the limits of table 3 by
not more than 100 K for an area not greater than
2 cm²
(PCB) to 20.1.3, exceeding the limits of table 3 by
not more than 100 K for an area not greater than
2 cm²
No area where temperature
exceeds 100K above limits
exceeds 100K above limits
N/A
b) Temperature rise of printed circuit boards
(PCB) to 20.1.3 up to 300 K for an area not greater
than 2 cm² for a maximum of 5 min
(PCB) to 20.1.3 up to 300 K for an area not greater
than 2 cm² for a maximum of 5 min
No area where temperature
exceeds 300K above limits
exceeds 300K above limits
N/A
- Page 14 of 45 -
Report
No.
98503
Meets all the special conditions if conductors on
printed circuit boards are interrupted
printed circuit boards are interrupted
No conductors are
interrupted /peeled/loosened
during fault conditions
interrupted /peeled/loosened
during fault conditions
N/A
Class I protective earthing maintained
Class II equipment
N/A
11.2.4
Temperature rise of parts acting as a support or
mechanical barrier
mechanical barrier
Temperature rises are
within the limits.
within the limits.
N/A
11.2.5
Temperature rise of windings
See appended table
P
11.2.6
Temperature rise of parts not subject to the limits
of 11.2.1 to 11.2.5
of 11.2.1 to 11.2.5
No excessive temperature
observed/measured on
other parts.
See appended table
observed/measured on
other parts.
See appended table
P
12 MECHANICAL
STRENGTH
12.1.1
Bump test where mass >7 kg
No damage in the sense
of this standard
of this standard
P
12.1.2 Vibration
test
Assessed to be satisfactory
constructed
constructed
N/A
12.1.3
Impact hammer test
No damage in the sense
of this standard
of this standard
P
Steel ball test
No damage in the sense
of this standard
of this standard
P
12.1.4
Drop test for portable apparatus where mass < 7
kg
kg
No portable apparatus
N/A
12.1.5
Thermoplastic enclosures strain relief test
Tested, 70ºC, 7h
P
12.2
Fixing of knobs, push buttons, keys and levers
Normal use will not impair
the protection against
electric shock.
the protection against
electric shock.
P
12.3
Remote controls with hazardous live parts
No cable connected
remote control devices.
remote control devices.
N/A
12.4
Drawers (pull test 50 N, 10 s)
No drawers
N/A
12.5
Antenna coaxial sockets providing isolation
No antenna socket which
insolate hazardous live
parts from accessible parts.
insolate hazardous live
parts from accessible parts.
N/A
Click on the first or last page to see other HK 3490 (serv.man2) service manuals if exist.