DOWNLOAD Harman Kardon HD 980 (serv.man3) Service Manual ↓ Size: 3.39 MB | Pages: 59 in PDF or view online for FREE

 

                                                                                    Page 3 of 57                         Report No. SH08050531-001 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

Test case does not apply to the test object.................. : N/A 

Test item does meet the requirement........................... : P(ass) 

Test item does not meet the requirement .................... : F(ail) 

Date of receipt of test item ........................................... : May 16, 2008 

Date(s) of performance of test...................................... : May 16, 2008 – May 30, 2008 

 

 
This report shall not be reproduced except in full without the written approval of the testing laboratory. 
 
The test results presented in this report relate only to the item(s) tested. 
 
Determination of the test result includes consideration of measurement uncertainty from the test equipment 
and methods. 
 
"(see appended table)" refers to a table appended to the report. 

“(see remark #)” refers to a remark appended to the report. 

“(see Annex #) refers to an annex appended to the report. 

 
Throughout this report a point is used as the decimal separator. 

 

General product information: 
 
Factory: WANLIDA GROUP CO., LTD. 
Factory site:

 

WANLIDA INDUSTRY ZONE, NANJING, FUJIAN, CHINA. 363601 

Tropical climate condition considered. 

 
 

 

                                                                                Page 4 of 57                        Report No. SH08050531-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

3 GENERAL 

REQUIREMENTS 

 

 

Safety class of the apparatus ................................. : Class II Pass 

 
 

4 

GENERAL CONDITIONS OF TESTS 

 

4.1.4 Ventilation 

instructions 

require the use of the test 

box 

Yes Pass 

 
 

5 MARKING 

 

 

Comprehensible and easily discernible 

Printed on the rear enclosure 

Pass 

 

Permanent durability against water and petroleum 
spirit 

 Pass 

5.1 Identification, 

maker, 

model ................................... : harman/kardon Pass 

 

Class II symbol if applicable 

 

Pass 

 

Rated supply voltage and symbol .......................... : 100-240V ~ 

Pass 

 

Frequency if safety dependant 

50/60Hz 

Pass 

 

Rated current or power consumption  .................... : 20W Pass 

5.2 

Earth terminal 

Class II 

N/A 

 

Hazardous live terminals 

 

N/A 

 

Supply output terminals (other than mains) 

 

N/A 

5.3 

Use of triangle with exclamation mark 

On PCB  

Pass 

5.4 

Instructions for use 

 

Pass 

5.4.1 

Mains powered equipment not exposed to dripping 
or splashing. Warning concerning objects filled 
with liquid, etc. 

 Pass 

 

Hazardous live terminals, instructions for wiring 

No such terminals 

N/A 

 

Instructions for replacing lithium battery 

No lithium battery 

N/A 

 

Instructions for modem if fitted 

No modem fitted 

N/A 

 

Class I earth connection warning 

 

N/A 

 

Instructions for multimedia system connection 

 

Pass 

 

Special stability warning for fixed installation 

 

N/A 

5.4.2 

Disconnect device: plug/coupler or all-pole mains 
switch location, accessibility and markings 

 Pass 

 

Instructions for permanently connected equipment  

N/A 

 

                                                                                Page 5 of 57                        Report No. SH08050531-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

6 HAZARDOUS 

RADIATION 

 

6.1 

Ionizing radiation < 36 pA/kg (0,5 mR/h) 

No ionizing radiation 

N/A 

6.1 

EN 60065 

European Council Directive 96/29/Euratom of 13 
May 1996 10cm from outer surface of apparatus 
<1µSv/h (0,1mR/h) 

No ionizing radiation 

N/A 

6.2 

Laser radiation, emission limits to IEC 60825-1  .... : Class 1 

Pass 

 

Emission limits under fault conditions .................... : Laser Optical Pickup: Class 1 

Pass 

 
 

7 

HEATING UNDER NORMAL OPERATING CONDITIONS 

 

7.1 

Temperature rises not exceeding specified values, 
no operation of fuse links 

(see appended table) 

Pass 

7.1.1 

Temperature rise of accessible parts 

(see appended table) 

Pass 

7.1.2 

Temperature rise of parts providing electrical 
insulation 

(see appended table) 

Pass 

7.1.3 

Temperature rise of parts acting as a support or as 
a mechanical barrier 

(see appended table) 

Pass 

7.1.4 

Temperature rise of windings 

(see appended table) 

Pass 

7.1.5 

Parts not subject to a limit under 7.1.1 to 7.1.4 

(see appended table) 

Pass 

7.2 

Softening temperature of insulating material 
supporting parts conductively connected to the 
mains carrying a current > 0,2 A at least 150

 o

C 

No such supporting parts 

N/A 

 
 

8 

CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION 
AGAINST ELECTRIC SHOCK 

 

8.1 

Conductive parts covered by lacquer, paper, 
untreated textile oxide films and beads etc. 
considered to be bare 

PCB, windings 

Pass 

8.2 

No shock hazard when changing voltage setting 
device, fuse-links or handling drawers etc. 

Tools are required 

Pass 

8.3 

Insulation of hazardous live parts not provided by 
hygroscopic material 

No hygroscopic material used 

Pass 

8.4 

No risk of electric shock following the removal of a 
cover which can be removed by hand 

Tools are required 

Pass 

8.5 

Class I equipment 

 

N/A 

 

Basic insulation between hazardous live parts and 
earthed accessible parts 

 N/A 

 

Resistors bridging basic insulation complying with 
14.2.1 a) 

         

 N/A 

 

                                                                                Page 6 of 57                        Report No. SH08050531-001 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

8.6 

Class II equipment and Class II constructions 
within Class I equipment 

 Pass 

 

Reinforced or double insulation between 
hazardous live parts and accessible parts 

 Pass 

 

Components bridging reinforced or double 
insulation complying with 14.1 a) or 14.3 

TR1 Pass 

 

Basic and supplementary insulation each being 
bridged by a capacitor complying with 14.2.1 a) 

 N/A 

 

Reinforced or double insulation being bridged with 
2 capacitors in series complying with 14.2.1 a) 

 N/A 

 

Reinforced or double insulation being bridged with 
a single capacitor complying with 14.2.1 b) 

CY1, CY2, CY3 

Pass 

 

Basic insulation bridged by components complying 
with 14.3.4.3 

 N/A 

8.7 

Basic insulation between parts at 35 V to 71 V 
(peak) a.c. or 60 V to 120 V d.c. and accessible 
parts 

No such voltage 

N/A 

 

Reinforced or double insulation between circuits 
operating at voltages between 35 V and 71 V 
(peak) a.c. or between 60 V and 120 V d.c. and 
hazardous live parts at higher voltage 

 N/A 

 

Separation by Class II isolating transformer 

 

N/A 

 

Separation by Class I transformer 

 

N/A 

 

Separation by earthed conductive part 

 

N/A 

8.8 

Basic or supplementary insulation > 0,4 mm (mm) :  

N/A 

 

Reinforced insulation > 0,4 mm (mm) .................... : TR1 bobbin: 0.8mm min. 

Optocoupler PH1:0.40mm min. 

Enclosure (front panel): 1.5mm 
min. 

Separation sheet on internal 
enclosure under power board: 
0.4mm min. 

Pass 

 

Thin sheet insulation 

Inside TR1. 

Pass 

 

Basic or supplementary insulation, at least two 
layers, each meeting 10.3 

Withstand 2120Vp test. 

Pass 

 

Basic or supplementary insulation, three layers any 
two of which meet 10.3 

 N/A 

 

Reinforced insulation, two layers each of which 
meet 10.3 

 N/A