DOWNLOAD Harman Kardon DVD 22 (serv.man2) Service Manual ↓ Size: 2.1 MB | Pages: 41 in PDF or view online for FREE

 

Test report no. JSH0311046-001 

Page 17 of 21

 

 

 
9.1 Test result 
 
           Pass               Fail              Not Applicable 
 
9.2 Operating environment 
 
Temperature:                           22

°C  

Relative Humidity:                  55%  
 
 
9.3 Test set up 
 

The measuring set up is shown in the following figure. 
 

 
 
 
 
 
 

 

Test report no. JSH0311046-001 

Page 18 of 21

 

 
 
 
 
 

 

 
 
9.4 Test protocol 
 
PASS 
 

 

Test report no. JSH0311046-001 

Page 19 of 21

 

 

 
10.1 Test result 
 
     Pass              Fail             Not Applicable 
 
10.2 Operating environment 
 
Temperature:                           22°C  
 
Relative Humidity:                  51%  
 
10.3 Test set-up 
 
The EUT was placed on a non-metallic table 0,8m above a reference ground plane (RGP) and was put 
into operation according to the specified operating mode. 
   
10.4 Test conditions 
 
Test level:                             1kV                AC mains  
 
Performance criterion:          B 
 
Repetition rate;                      5kHz 
 
Application method:             AC mains 
 
Duration of each test:            2 min 
 
Lines for test:                         AC mains 
 
EUT-position:                        Table top

/floor standing

 

 
10.5 Measurement uncertainty 
 
The uncertainty of the applied fast transient/burst is within the tolerance specified by the standard. 
 
10.6 Test protocol 
 
 
Test No. 

# 

Level 

[kV] 

Polarity 

+/- 

Line for test 

Pass/ 

Fail 

Comment 

1 1 + 

AC 

mains  P 

 

2 1 - 

AC 

mains  P 

 

 

 

Test report no. JSH0311046-001 

Page 20 of 21

 

 

 
11.1 Test result 
 
           Pass               Fail              Not Applicable 
 
11.2 Operating environment 
 
Temperature:                           22

°C  

Relative Humidity:                  55%  
 
11.3 Test set-up 
 
<Floor standing>The EUT was placed on a non-metallic support 0,1m above a reference ground plane 
(RGP) and was put into operation according to the specified operating mode. 
 
<Table top>A horizontal coupling plane (HCP) was placed on a 0.8m high non-metallic table above a 
2.6m by 1.8m reference ground plane (RGP) and connected to it through a cable with two 470k

Ω 

resistors at each end. The EUT was placed on an insulation sheet on the HCP and was put into operation 
according to the specified operating mode. 
 
A vertical coupling plane (VCP) was connected to the RGP through a cable with two 470k

Ω resistors at 

each end. 
 
   
11.4 Test conditions 
 
Test level:                                            4kV Contact discharge 
                                                             8kV Air discharge 
 
Number of discharges 
at each point:                                       10 of each polarity 
 
Performance criterion:                         B 
 
ETU position:                                       Table top standing 
 
Indirect contact discharges were applied to the VCP and the HCP The selected test points of the EUT are 
listed in this table.. 
 

HCP f  0,1m from the front of the EUT 

Edge of centre,coner  on HCP 

 

HCP b  0,1m from the back of the EUT 

Edge of centre,coner  on HCP 

 

HCP r  0,1m from the right side of the EUT 

Edge of centre,coner  on HCP 

 

HCP l 

0,1m from the left side of the EUT 

Edge of centre,coner  on HCP 

 

VCP f  0,1m from the front of the EUT 

Edge of centre,coner  on VCP 

 

VCP b  0,1m from the back of the EUT 

Edge of centre,coner  on VCP 

 

VCP r  0,1m from the right of the EUT 

Edge of centre,coner  on VCP 

 

VCP l 

0,1m from the left of the EUT 

Edge of centre,coner  on VCP 

 

 
.