Harman Kardon DAL 150 (serv.man2) User Manual / Operation Manual ▷ View online
5
Important Information for the User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio-frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio-frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the computer to which the equipment is connected into an
• Increase the separation between the equipment and receiver.
• Connect the computer to which the equipment is connected into an
AC outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept interference received,
including interference that may cause undesired operation.
NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and
may void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
(1) this device may not cause harmful interference, and (2) this device must accept interference received,
including interference that may cause undesired operation.
NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and
may void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
6
GENERAL INSTALLATION INSTRUCTIONS
The precise dialog boxes and messages that will appear on your computer screen at various points during the
installation procedure will vary depending upon the version of the Windows operating system that has been installed on
your computer. Since installing a USB device on your computer is a fairly automatic process, you may wish to
proceed by following these general installation instructions.
installation procedure will vary depending upon the version of the Windows operating system that has been installed on
your computer. Since installing a USB device on your computer is a fairly automatic process, you may wish to
proceed by following these general installation instructions.
Step One – Connect USB Cable to DAL 150 and PC
Plug the USB cable into the DAL 150 and into an available USB port on either your computer or an optional,
powered, external USB hub.
Plug the USB cable into the DAL 150 and into an available USB port on either your computer or an optional,
powered, external USB hub.
Step Two – Install CD-ROM
At this point your computer should recognize that a USB device has been attached to it, and one or more screens will
appear to confirm that the “Found New Hardware Wizard” has been launched. You may need to click the “Next” button
through several dialog boxes in order to reach a box similar to the one shown in Figure 1 (which was taken from a
Windows XP installation) that asks you to install the supplied CD-ROM and install the
software driver automatically. Click the “Next” button to begin the installation.
At this point your computer should recognize that a USB device has been attached to it, and one or more screens will
appear to confirm that the “Found New Hardware Wizard” has been launched. You may need to click the “Next” button
through several dialog boxes in order to reach a box similar to the one shown in Figure 1 (which was taken from a
Windows XP installation) that asks you to install the supplied CD-ROM and install the
software driver automatically. Click the “Next” button to begin the installation.
Figure 1– Windows Operating System
Found New Hardware Wizard
7
If you are using the Windows XP operating system, you may see a screen warning you that the DAL 150
software has not been verified as compatible. Other versions of Windows may report that the software may not work
correctly. You may confidently proceed. Although there was no Digital Signature for the 8051 firmware used by the DAL
150 as of the printing of this installation guide, the software has been thoroughly tested for
full compatibility with the Windows 98SE, Me, 2000 and XP operating systems and is safe to install.
software has not been verified as compatible. Other versions of Windows may report that the software may not work
correctly. You may confidently proceed. Although there was no Digital Signature for the 8051 firmware used by the DAL
150 as of the printing of this installation guide, the software has been thoroughly tested for
full compatibility with the Windows 98SE, Me, 2000 and XP operating systems and is safe to install.
Step Three – PC Installs Software
At the same point during the installation, the computer should indicate that the software program being loaded is called
“Loader 8051 firmware.” The computer may also indicate its location as “D:\MGMP3.INF” (or some other drive letter
associated with the CD-ROM or DVD-ROM drive on your computer) in some versions of the Windows operating system. If
your computer is attempting to install a different software driver, cancel the
installation and go back to the screen that will allow you to specify the location of the correct software driver.
Allow the computer a few minutes to install the software driver without interruption. A dialog box, similar
to the one shown in Figure 2, should appear. Click the “Finish” button to complete the installation.
At the same point during the installation, the computer should indicate that the software program being loaded is called
“Loader 8051 firmware.” The computer may also indicate its location as “D:\MGMP3.INF” (or some other drive letter
associated with the CD-ROM or DVD-ROM drive on your computer) in some versions of the Windows operating system. If
your computer is attempting to install a different software driver, cancel the
installation and go back to the screen that will allow you to specify the location of the correct software driver.
Allow the computer a few minutes to install the software driver without interruption. A dialog box, similar
to the one shown in Figure 2, should appear. Click the “Finish” button to complete the installation.
Figure 2 – Software Driver Installation Complete
8
Step Four – Verify Installation
When the installation has finished, a small “hk” logo should appear in the Windows systray or task bar in the lower right
corner of your screen (see Figure 3). If you do not see this logo, try momentarily unplugging the USB cable from your
computer’s USB port, or from the external hub, and then plugging in the USB cable again.
When the installation has finished, a small “hk” logo should appear in the Windows systray or task bar in the lower right
corner of your screen (see Figure 3). If you do not see this logo, try momentarily unplugging the USB cable from your
computer’s USB port, or from the external hub, and then plugging in the USB cable again.
or
Figure 3 – “hk” logo in systray
Step Five – Install Windows Media Player
Upon installation of the software driver for the DAL 150, the software will automatically check your system
for the presence of the proper version of Windows Media Player. If you are using the Windows Me or Windows XP
operating system, you should already have Windows Media Player Version 7.0 or higher installed on your system. If the
Player is not found, you will be prompted to install it.
Exit your other applications, and click on the “Yes” button.
You will be prompted by several dialog boxes to:
Upon installation of the software driver for the DAL 150, the software will automatically check your system
for the presence of the proper version of Windows Media Player. If you are using the Windows Me or Windows XP
operating system, you should already have Windows Media Player Version 7.0 or higher installed on your system. If the
Player is not found, you will be prompted to install it.
Exit your other applications, and click on the “Yes” button.
You will be prompted by several dialog boxes to:
• Read the license agreement and click “Yes” to accept it;
• Read the “Welcome” box and click “Next” to proceed with the Windows Media Component Setup;
• Read the Privacy Statement, check the box indicating that you have read it, and click the
• Read the “Welcome” box and click “Next” to proceed with the Windows Media Component Setup;
• Read the Privacy Statement, check the box indicating that you have read it, and click the
“Next” button to proceed;
• Read the list of components that will be installed, uncheck any you do not desire (we recommend installing
all components at this time), and click the “Next” button to proceed;
• Read the configuration screen that determines when the Player will be launched automatically, uncheck any
configurations not desired (you must leave the MPEG Layer 3 files box checked in order for the DAL 150 to
function correctly), and click the “Next” button to proceed;
function correctly), and click the “Next” button to proceed;
• Click the “Next” button to install Windows Media Player; and
• Click the “Finish” button once the Setup has completed, which will reboot your computer.
• Click the “Finish” button once the Setup has completed, which will reboot your computer.
Click on the first or last page to see other DAL 150 (serv.man2) service manuals if exist.