Harman Kardon BDT 30 - BDT 3 (serv.man3) Service Manual ▷ View online
harman/kardon
Service Manual
BDT 30/230
BDT 3/120
BDT 3/120
Blu-ray player
Released EU2011
Harman Consumer Group, Inc.
Rev 0, 10/2011
8500 Balboa Boulevard
Northridge, California 91329
ESD WARNING
2
OWNER’S MANUAL FRONT PAGE
3
REGION CODES
4
FEATURES
5
FRONT PANEL CONTROLS
6
REAR-PANEL CONNECTIONS
7
REMOTE CONTROL FUNCTIONS
7
TROUBLESHOOTING
9
SPECIFICATIONS
10
EXPLODED VIEW
11
BDT 3 PARTS LIST
12
BDT 30 PARTS LIST
13
SOFTWARE UPGRADE INSTRUCTIONS 14
TROUBLESHOOTING CHARTS
15
PCB DRAWINGS
19
WIRING DIAGRAM
23
SCHEMATIC DIAGRAMS
24-35
CONTENTS
Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol
in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
CAUTION :
Harman Kardon
BDT 3/120V and BDT 30/240V Service Manual
Page 2 of 35
Blu-ray Disc
™
player
BDT 3/BDT 30
Owner’s Manual
Harman Kardon
BDT 3/120V and BDT 30/240V Service Manual
Page 3 of 35
English
Unpacking
The carton and shipping materials used to protect your new player during shipment were
specially designed to cushion it from shock and vibration. We suggest that you save the
carton and packing materials for use in shipping if you move or if the unit ever needs
repair.
To minimize the size of the carton in storage, you may wish to flatten it. you can do it by
To minimize the size of the carton in storage, you may wish to flatten it. you can do it by
carefully slitting the tape seams on the carton’s bottom and collapsing it. you can store
cardboard inserts in the same manner. Packing materials that cannot be collapsed should
be saved along with the carton in a plastic bag.
If you do not wish to save the packaging materials, please note that the carton and
If you do not wish to save the packaging materials, please note that the carton and
other sections of the shipping-protection materials are recyclable. Please respect the
environment and discard those materials at a local recycling center.
Remove the protective plastic film from the front-panel lens. leaving the film in place will
Remove the protective plastic film from the front-panel lens. leaving the film in place will
affect the performance of your remote control.
Installation Location
• To ensure proper operation and to avoid the potential for safety hazards, place the
unit on a firm and level surface. When placing the unit on a shelf, be certain that the
shelf and any mounting hardware can support the weight of the product.
• Provide proper space both above and below the unit for ventilation. If this product
will be installed in a cabinet or other enclosed area, make certain that there is
sufficient air movement within the area. under some circumstances, a fan may
be required.
• do not place the unit directly on a carpeted surface.
• Avoid installation in extremely hot or cold locations, or in an area that is exposed to
direct sunlight or heating equipment.
• Avoid moist or humid locations.
• do not obstruct the ventilation slots on the top and sides of the unit or place objects
directly over or next to them.
• do not place the BdT 3/BdT 30 directly on top of a product that generates
excessive heat.
• due to the heat generated by the player and other components in your system,
there is the remote possibility that the rubber padding on the bottom of the unit’s
feet may leave marks on certain wood or wood-veneer materials. use caution
when placing the unit on soft woods or other materials that heat or heavy objects
may damage. some surface finishes may be particularly sensitive to absorbing
such marks, due to a variety of factors beyond harman kardon control, including
the nature of the finish, cleaning materials used, normal heat and vibration caused
by the use of the product, or other factors. your warranty will not cover this type of
damage to furniture, so exercise caution in choosing an installation location for the
component and in performing normal maintenance practices.
• your new harman kardon Blu-ray disc
™
player requires a broadband Internet
connection for Bd-live
™
interactivity.
Cleaning
• When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only
after unplugging the Ac power cord, wipe it with a soft cloth dampened with mild
soapy water, then a fresh cloth with clean water. Wipe it dry immediately with a
dry cloth. NeveR use benzene, aerosol cleaners, paint thinner, alcohol or any other
volatile cleaning agent. do not use abrasive cleaners, as they may damage the
finish of metal parts. Avoid spraying insecticide near the unit.
Please register your product on our Web site at
www.harmankardon.com.
Note: you’ll need the product’s serial number.
Note: you’ll need the product’s serial number.
At the same time, you can choose to be
notified about our new products and/or special
promotions.
Thank You for Choosing Harman Kardon
®
Products!
for more than fifty years, harman kardon products have been at the cutting edge of audio
and home theater technology. The first audio receiver wore a harman kardon badge, and
the company has been producing innovative entertainment products ever since. The BdT
3/BdT 30 Blu-ray disc
™
player is the latest component offered in that proud tradition.
Incorporating the latest 3-d, high-definition audio and video processing technologies, the
BdT 3/BdT 30 is an essential part of a modern home theater system. It plays your favorite
Blu-ray disc movies with up to 1080/24p video resolution when available on the disc, and
thanks to hdMI
®
(high-definition Multimedia Interface
®
) 1.4a with 30/36-bit deep color
connectivity, lets you experience the latest 3-d home entertainment when you connect
it to a 3-d-capable Tv.
connect the BdT 3/BdT 30 to the Internet, and Bd-live
connect the BdT 3/BdT 30 to the Internet, and Bd-live
™
interactivity (available with
compatible discs) delivers additional features, updates and news of live events. even your
older dvd-video discs will deliver outstanding picture quality when they are upscaled to
1080p video resolution.
yet with all of its sophistication, the BdT 3/BdT 30 is simple to operate. Its controls are
yet with all of its sophistication, the BdT 3/BdT 30 is simple to operate. Its controls are
similar to those of dvd players, and its enhanced on-screen menu system guides you
every step of the way. easy to use and delivering outstanding performance, the BdT 3/
BdT 30 is sure to provide enjoyment for many years to come.
If you have any questions about this product, its installation or its operation, please
If you have any questions about this product, its installation or its operation, please
contact your retailer or custom installer, or visit the harman kardon Web site at
www.harmankardon.com.
NOTE: your Blu-ray disc player is designed and manufactured for compatibility
with region management information that is encoded on most Blu-ray disc
recordings and dvd recordings:
•
BDT 3 units are designed only for playback of discs with Blu-Ray disc
Region code A and dvd Region code 1 information, or for discs that do
not contain any Region code information.
•
BDT 30 units are designed only for playback of discs with Blu-ray disc
Region code B and dvd Region code 2 information, or for discs that do
not contain Region code information.
1
2
If there is a Region code on a disc other than the one your BdT player is
designed for, it will not play in your BdT player.
5
Unpacking
Harman Kardon
BDT 3/120V and BDT 30/240V Service Manual
Page 4 of 35