Harman Kardon AVR 7500 (serv.man9) EMC - CB Certificate ▷ View online
-
IEC 60065, 6th edition : 1998
-
- Page 29 of 43 -
Order No.
200211175
16.6
Apertures for external flexible cord:
no risk of damage to the cord during
assembly or movement in use
no risk of damage to the cord during
assembly or movement in use
No sharp edges
P
16.7
Transportable musical instruments
and assosiated amplifiers fitted with
detachable cord set with appliance
inlet to IEC 60 320-1
and assosiated amplifiers fitted with
detachable cord set with appliance
inlet to IEC 60 320-1
The apparatus is not a transportable musical instrument
and amplifier
and amplifier
N
Transportable musical instruments
and amplifiers fitted with cord and
with means of stowage to protect the
cord
and amplifiers fitted with cord and
with means of stowage to protect the
cord
The apparatus is not a transportable musical instrument
and amplifier
and amplifier
N
17
ELECTRICAL CONNECTIONS AND
MECHANICAL FIXINGS
MECHANICAL FIXINGS
P
17.1
Torque test to Table 12:
P
Screw
Diameter
With
Without
Material
Torque test (Nm)
Location/function
(mm)
head
head
Screw
Nut
Fulfilled /Remarks
Top enclosure (side)
4
x
Metal
Metal
Tested with 1,2Nm /
Pass
Pass
Top enclosure (rear)
3
x
Metal
Metal
Tested with 0,5Nm /
Pass
Pass
17.2
Correct introduction into female
threads in non-metallic material
threads in non-metallic material
No female threads in non-metallic materials
N
17.3
Cover fixing screws: captive
Captivity not necessary, see below
P
Non-captive fixing screws: no hazard
when replaced by a screw whose
length is 10 times its diameter
when replaced by a screw whose
length is 10 times its diameter
Tested with screw with 10 times diameter.
P
17.4
No loosening of conductive parts
carrying a current > 0,2 A
carrying a current > 0,2 A
Loosening is sufficiently prevented
P
17.5
Contact pressure not transmitted
through plastic other than ceramic
for connections carrying a current
> 0,2 A
through plastic other than ceramic
for connections carrying a current
> 0,2 A
No contact pressure transmitted through insulating
material.
material.
P
17.6
Stranded conductors of flexible
supply cords carrying a current
> 0,2 A with screw terminals not
consolidated by solder
supply cords carrying a current
> 0,2 A with screw terminals not
consolidated by solder
No screw terminals
N
-
IEC 60065, 6th edition : 1998
-
- Page 30 of 43 -
Order No.
200211175
17.7
Cover fixing devices other than
screws have adequate strength and
their positioning is unambiguous
screws have adequate strength and
their positioning is unambiguous
No cover fixing devices other than screws
N
17.8
Fixing devices for detachable legs or
stands provided
stands provided
No detachable provided
N
17.9
Internal pluggable connections,
affecting safety, unlikely to become
disconnected
affecting safety, unlikely to become
disconnected
Connections complies, checked by inspection
P
18
MECHANICAL STRENGTH OF
PICTURE TUBES AND
PROTECTION AGAINST THE
EFFECTS OF IMPLOSION
PICTURE TUBES AND
PROTECTION AGAINST THE
EFFECTS OF IMPLOSION
N
18.1
Picture tube separately approved
No picture tube.
N
Picture tubes > 16 cm intrinsically
protected
protected
N
Non-intrinsically protected tubes
> 16 cm used with protective screen
> 16 cm used with protective screen
N
18.2
Intrinsically protected tubes: tests
on 12 samples
on 12 samples
N
18.2.1
Samples subject to ageing: 6
N
18.2.2
Samples subject to implosion test: 6
N
18.2.3
Samples subject to mechanical
strength test (steel ball): 6
strength test (steel ball): 6
N
18.3
Non-intrinsically protected tubes
tested to 18.3
tested to 18.3
N
19
STABILITY AND MECHANICAL
HAZARDS
HAZARDS
P
Mass of the equipment exceeding
18 kg
18 kg
Mass > 18 kg, see below
P
19.1
Test on a plane, inclined at 10
°
to
the horizontal
Tested on a plane inclined at an angle of 10
°
P
19.2
100 N force applied vertically
downwards
downwards
100N force have no influence on the stability
P
19.3
Smooth edges and corners
There is no hazardous edges or corners when the
apparatus is operating in normal position
apparatus is operating in normal position
P
19.4
Glass surfaces with an area
exceeding 0,1 m² or maximum
dimension > 450 mm, pass the test
of 19.4.1
exceeding 0,1 m² or maximum
dimension > 450 mm, pass the test
of 19.4.1
No glass surface.
N
-
IEC 60065, 6th edition : 1998
-
- Page 31 of 43 -
Order No.
200211175
20
RESISTANCE TO FIRE
P
20.1
Electrical components and
mechanical parts
mechanical parts
P
Apparatus design
Resistance to fire is achieved by a combination of
engineering design, production methods and by using
materials with low flammability for internal parts
engineering design, production methods and by using
materials with low flammability for internal parts
P
a) Exemption for components
contained in an enclosure of material
FV 0 to IEC 60 707 with openings
not exceeding 1 mm in width
contained in an enclosure of material
FV 0 to IEC 60 707 with openings
not exceeding 1 mm in width
N
b) Exemption for small components
as defined in 20.1
as defined in 20.1
PCB is of flammability class FV 1 or better, and
exception is made for small components.
exception is made for small components.
P
20.1.1
Electrical components meet the
requirements of 14.2.5, 14.4, 14.5.3,
14.6.6 or 20.1.4
requirements of 14.2.5, 14.4, 14.5.3,
14.6.6 or 20.1.4
No other electrical components with additional
flammability requirements.
flammability requirements.
N
20.1.2
Insulation of internal wiring working
at voltages > 4 kV or leaving an
internal fire enclosure, not
contributing to the spread of fire
at voltages > 4 kV or leaving an
internal fire enclosure, not
contributing to the spread of fire
No wires working at voltages > 4kV or leaving an internal
fire enclosure
fire enclosure
N
20.1.3
Material of printed circuit boards on
which the available power exceeds
15 W at a voltage between 50 V and
400 V (peak) a.c. or d.c. meets FV 1
or better to IEC 60 707, unless used
in a fire enclosure
which the available power exceeds
15 W at a voltage between 50 V and
400 V (peak) a.c. or d.c. meets FV 1
or better to IEC 60 707, unless used
in a fire enclosure
All PCB are of base material with flammability category
FV 1 or better. See List of Critical Components.
FV 1 or better. See List of Critical Components.
P
Material of printed circuit boards on
which the available power exceeds
15 W at a voltage exceeding 400 V
(peak) a.c. or d.c. meets FV 0 to
IEC 60 707
which the available power exceeds
15 W at a voltage exceeding 400 V
(peak) a.c. or d.c. meets FV 0 to
IEC 60 707
< 400V(peak)
N
20.1.4
Components and parts not covered
by 20.1.1, 20.1.2 and 20.1.3 (other
than fire enclosures) mounted nearer
to a potential ignition source than
the distances in Table 13 comply
with the relevant flammability
category in Table 13
by 20.1.1, 20.1.2 and 20.1.3 (other
than fire enclosures) mounted nearer
to a potential ignition source than
the distances in Table 13 comply
with the relevant flammability
category in Table 13
N
Components and parts as above but
shielded from a potential ignition
source, with the barrier area in
accordance with Table 13 and fig. 13
shielded from a potential ignition
source, with the barrier area in
accordance with Table 13 and fig. 13
N
20.2
Fire enclosure
N
20.2.1
Potential ignition sources with open
circuit voltage > 4 kV (peak) a.c. or
d.c. contained in a fire enclosure to
FV 1
circuit voltage > 4 kV (peak) a.c. or
d.c. contained in a fire enclosure to
FV 1
No voltages exceeding 4kV, no fire enclosure
requirement.
requirement.
N
-
IEC 60065, 6th edition : 1998
-
- Page 32 of 43 -
Order No.
200211175
20.2.2
Internal fire enclosures with openings
not exceeding 1 mm in width and
with openings for wires completely
filled
not exceeding 1 mm in width and
with openings for wires completely
filled
No internal fire enclosure.
N
20.2.3
Requirements of 20.2.1 and 20.2.2
met by an internal fire enclosure
met by an internal fire enclosure
N
A
ANNEX A, ADDITIONAL
REQUIREMENTS FOR
APPARATUS WITH PROTECTION
AGAINST SPLASHING WATER
REQUIREMENTS FOR
APPARATUS WITH PROTECTION
AGAINST SPLASHING WATER
Not intended for outdoor use.
N
A.5.1
j) Marked with IPX4 (IEC 60 529),
5.4.1 a) does not apply
5.4.1 a) does not apply
N
A.10.2.1
Enclosure provides protection
against splashing water
against splashing water
N
A.10.2.2
Humidity treatment carried out for
7 days
7 days
N
B
ANNEX B, APPARATUS TO BE
CONNECTED TO THE
TELECOMMUNICATION
NETWORKS
CONNECTED TO THE
TELECOMMUNICATION
NETWORKS
Not intended for telecommunication networks
N
B.5.4.1
e) Where the separation of TNV
circuits from other circuits relies on
protective earthing the instructions
make it clear that protective earthing
is essential
circuits from other circuits relies on
protective earthing the instructions
make it clear that protective earthing
is essential
N
B.8.1
TNV circuits separated from the
mains circuit and from hazardous
live parts by either:
mains circuit and from hazardous
live parts by either:
N
a) double or reinforced insulation
N
b) basic insulation with earthed
protective screening
protective screening
N
B.8.2
TNV circuits separated from circuits
other than those in B.8.1 and from
accessible conductive parts by basic
insulation meeting the requirements
for clearances and creepage
distances for the voltages concerned
other than those in B.8.1 and from
accessible conductive parts by basic
insulation meeting the requirements
for clearances and creepage
distances for the voltages concerned
N
B.9.1.1
TNV circuit terminals contacts which
cannot be touched by probe B.1,
exempt from the requirements
inaccessible terminal contacts in
9.1.1
cannot be touched by probe B.1,
exempt from the requirements
inaccessible terminal contacts in
9.1.1
N
Click on the first or last page to see other AVR 7500 (serv.man9) service manuals if exist.