Harman Kardon AVR 171S (serv.man4) Service Manual ▷ View online
Data Sheet: DM Series
DM860A Networked Media Processor
dat_DM860A_1_1_datasheet.doc
CONFIDENTIAL
Version 1.1 – July 11
th
2011 - Page 17 of 70
2.9 Serial Peripheral Interface (SPI)
Name
Pin
Type Description
SPIDIN
D14
I
SPI data receive
SPIDOUT
D15
O
SPI data transmit
SPICLK B16
I/O
SPI
clock
SPINCS0 C15
I/O
Multi-master mode: chip-select input (used to detect bus conflict)
Master only mode:
Master only mode:
chip-select 1 output
Slave mode:
chip-select input
SPINCS1 B17
I/O
Multi-master mode: chip-select 2 output
Master only mode:
Master only mode:
chip-select 2 output
Slave mode:
not used
Harman Kardon
AVR 171 Service Manual
Page 89 of 174
Data Sheet: DM Series
DM860A Networked Media Processor
dat_DM860A_1_1_datasheet.doc
CONFIDENTIAL
Version 1.1 – July 11
th
2011 - Page 18 of 70
2.10 External Memory Interface
Name
Pin(s)
Type Description
D[15:0]
T18, R18, P17,
P18, N15, N16,
N17, N18, M15,
M16, M17, M18,
L15, L16, L17, L18
P18, N15, N16,
N17, N18, M15,
M16, M17, M18,
L15, L16, L17, L18
I/O Data bus for external memory and peripheral access
A[12:0]
E18, E17, E16,
E15, D18, D17,
D16, C18, C17,
C16, B18, A18,
A17
E15, D18, D17,
D16, C18, C17,
C16, B18, A18,
A17
O
Address bus for external memory and peripheral access
A13_RAS F15
O
SRAM: address
output
SDRAM: row
access
strobe
A14_CAS F16
O
SRAM: address
output
SDRAM: column access strobe
A15_BA0 F17
O
SRAM: address
output
SDRAM: bank
select
A16_BA1 F18
O
SRAM: address
output
SDRAM: bank
select
A17_DQM0 G15
O
SRAM: address
output
SDRAM: data
mask
A18_DQM1 G16
O
SRAM: address
output
SDRAM: data
mask
A[23:19]
H17, H16, H15,
G18, G17
G18, G17
O
Address bus for external memory and peripheral access
NCS[3:0]
H18, J17, J16, J15
O
Chip select signals. The active memory range for NCS[n]
(active low) can be configured.
(active low) can be configured.
x NCS[0] supports SRAM, can be used for booting
x NCS[1] supports SDRAM or SRAM
x NCS[2] supports SRAM
x NCS[3] supports SRAM
x NCS[1] supports SDRAM or SRAM
x NCS[2] supports SRAM
x NCS[3] supports SRAM
NOE
K17
O
Output enable, asserted (low) for read operations
NWE
K16
O
Write enable, asserted (low) for write operations
NWAIT K18
I
External wait line. If NWAIT is asserted, memory access will
be stalled. Can be configured as either low-active (default) or
high-active.
be stalled. Can be configured as either low-active (default) or
high-active.
MEMCLK K15
O SDRAM
system
clock
MEMCKE J18
O SDRAM
clock
enable
Harman Kardon
AVR 171 Service Manual
Page 90 of 174
Data Sheet: DM Series
DM860A Networked Media Processor
dat_DM860A_1_1_datasheet.doc
CONFIDENTIAL
Version 1.1 – July 11
th
2011 - Page 19 of 70
2.11 NAND-Flash Interface
Name
Pin(s)
Type Description
FD[7:0]
T17, T16, T15,
R17, R16, R15,
P16, P15
R17, R16, R15,
P16, P15
I/O
Bi-directional data bus
FALE
V18
O
Address latch enable;
pull-up/down defines boot mode
FCLE
U16
O
Command latch enable; pull-up/down defines boot mode
NFCE0 U15
O
Chip-enable,
low-active
NFRB
U18
I
Ready/busy. NAND flash is busy when NFRB is low.
NFRE
V17
O
Read enable, low-active
NFWE
U17
O
Write enable, low-active
NFWP
V16
O
Write protect, low-active
2.12 Ethernet MAC-Phy Interface (MII)
Name
Pin
Type
MII
RMII
SMII
MIIDIO
U14
I/O
management data
management data
MIIMDC
V14
O
management clock
management clock
MIIRXD[3]
V13
I
RxD 3
RxD 1
MIIRXD[2]
U13
I
RxD 2
RxD 0
MIIRXD[1] V12 I RxD
1
Rx-Sync
MIIRXD[0] U12 I RxD
0
RxD
MIIRXCLK T12
I receive
clock
receive
clock
MIIRXER
R13
I
receive error
receive error
MIIRXDV
T14
I
receive data valid
carrier sense/data valid
MIITXD[3]
V11
O
TxD 3
TxD 1
MIITXD[2]
U11
O
TxD 2
TxD 0
MIITXD[1] V10 O
TxD
1
Tx-Sync
MIITXD[0] U10 O
TxD
0
TxD
MIITXCLK R12 I transmit
clock
transmit
clock
MIITXER T11 O
transmit
error
MIITXEN
R11
O
transmit data enable
transmit data enable
MIICOL
T13
I
MII ethernet collision
MIICRS
R14
I
MII carrier sense
MIIPHYCLK
V15
O
25.000 MHz clock
50.000 MHz clock
125.000 MHz clock
Harman Kardon
AVR 171 Service Manual
Page 91 of 174
Data Sheet: DM Series
DM860A Networked Media Processor
dat_DM860A_1_1_datasheet.doc
CONFIDENTIAL
Version 1.1 – July 11
th
2011 - Page 20 of 70
2.13 USB 2.0 OTG
Name
Pin
Type Description
USBD+
B1
I/O Positive data line that is connected to the serial USB cable
USBD–
A1
I/O Negative data line that is connected to the serial USB cable
USBID
E2
I
USB ID pin of mini-AB receptacle
USBREXT
C2
I
External bias resistor (2K7, 1%); connect resistor to VSSUSB
USBVBUS
D2
I
VBUS voltage sense
USBVBUSDRV
E3
O
Control signal to control VBUS 5V voltage source
USBXTALI C4 I
Oscillator circuit input for a 24.000 MHz crystal (optional).
Without external crystal, pull this pin to GND.
Without external crystal, pull this pin to GND.
USBXTALO C3 O
Oscillator circuit output for a 24.000 MHz crystal (optional).
Without external crystal, leave this pin open.
Without external crystal, leave this pin open.
USBATST
D3
–
Do not connect
2.14 Power-on Reset Pins
Name
Pin
Type Description
NRES12REF D6 I
Voltage reference input. NRES12OUT is release when this input
voltage exceeds V
voltage exceeds V
TH12
.
NRES12OUT
C5
O
Open-drain reset (active low) for 1.2V core power supply.
NRES33REF D5 I
Voltage reference input. NRES33OUT is release when this input
voltage exceeds V
voltage exceeds V
TH33
.
NRES33OUT
D4
O
Open-drain reset (active low) for 3.3V core power supply
2.15 Real-Time Clock (RTC) Pins
Name
Pin
Type
Description
RTCXIN
F2
I
Oscillator circuit input. Connect 32.768 kHz tuning fork crystal here.
RTCXOUT
G2
O
Oscillator circuit output. Connect 32.768 kHz tuning fork crystal here.
VDD33RTC
F1
Power Power supply (+3.3 V) for RTC
VSS33RTC
E1
Power Ground (0 V) for RTC
Harman Kardon
AVR 171 Service Manual
Page 92 of 174
Click on the first or last page to see other AVR 171S (serv.man4) service manuals if exist.