Harman Kardon AURA (serv.man6) EMC - CB Certificate ▷ View online
Report No.: EM201300550-12 Application No.: ZJ00032797 Page 17 of 45
Channel 2442MHz
Report No.: EM201300550-12 Application No.: ZJ00032797 Page 18 of 45
Channel 2472MHz
Report No.: EM201300550-12 Application No.: ZJ00032797 Page 19 of 45
4.3 FREQUENCY RANGE
4.3.1 LIMITS
EN300 328 clause 4.3.3
fL > 2,4 GHz and fH < 2,4835 GHz
4.3.2 TEST METHOD
EUT operation status:
Keep EUT on transmitting mode by the software provided by
manufacturer.
Pretest the EUT at different transmission rate and report show
the worst case data.
manufacturer.
Pretest the EUT at different transmission rate and report show
the worst case data.
Test channel:
802.11b/g
Lowest channel: (2412MHz),Highest channel: (2472MHz)
Lowest channel: (2412MHz),Highest channel: (2472MHz)
Test condition:
Normal and extreme test conditions.
Test equipment used:
Refer to section 3.4
Test procedure:
1. Connect a low attenuation cable from the antenna port to the
spectrum.
2. Set spectrum analyzer center frequency is centered on test
channel; Set RBW and VBW = 100 kHz. Sweep = ≥1 min.
Span is wide enough to cover the complete power envelope
of the signal of the EUT. Detector function = Average,.
Trace = Max hold;
Span is wide enough to cover the complete power envelope
of the signal of the EUT. Detector function = Average,.
Trace = Max hold;
3. Find the cross point of limit and the trace. Save the trace.
Remark:
Pre-scan all the rate, found that:
11Mbps of rate is the worst case of 802.11b;
54Mbps of rate is the worst case of 802.11g ;
11Mbps of rate is the worst case of 802.11b;
54Mbps of rate is the worst case of 802.11g ;
4.3.3 TEST SETUP
Attenuator
EUT
Antenna
connector
Antenna
connector
Receiver
Report No.: EM201300550-12 Application No.: ZJ00032797 Page 20 of 45
4.3.4 TEST RESULTS
802.11b mode:
Measurement Conditions
Frequency spot with
level
≤ -30dBm/100KHz
Limit
(MHz)
Temperature
(°C)
(°C)
Voltage
(V
(V
AC
)
FL FH Lower
Higher
25 Vnom
2402.220
2481.800
FL>2400.0 FH< 2483.5
0
Vmin 2402.210
2481.820
Vmax 2402.220
2481.790
+70
Vmin 2402.21
2481.810
Vmax 2402.230
2481.750
FL: Lowest frequency of the power envelope, it is the frequency furthest below the frequency
of maximum power where the output power drops below the level of –80 dBm/Hz spectral
power density (-30 dBm if measured in a 100 kHz bandwidth) e.i.r.p.
FH: Highest frequency of the power envelope, it is the frequency furthest above the frequency
of maximum power where the output power drops below the level of –80 dBm/Hz spectral
power density (-30 dBm if measured in a 100 kHz bandwidth) e.i.r.p.
of maximum power where the output power drops below the level of –80 dBm/Hz spectral
power density (-30 dBm if measured in a 100 kHz bandwidth) e.i.r.p.
FH: Highest frequency of the power envelope, it is the frequency furthest above the frequency
of maximum power where the output power drops below the level of –80 dBm/Hz spectral
power density (-30 dBm if measured in a 100 kHz bandwidth) e.i.r.p.
Vnom =AC230V/50Hz;Vmin = AC207V/50Hz; Vmax= AC253V/50Hz
TEST RESULTS: The EUT compliant the requirements.
Click on the first or last page to see other AURA (serv.man6) service manuals if exist.