Sony SLV-SE85B / SLV-SE85NP / SLV-SE85UX / SLV-SE85VC / SLV-SF90B / SLV-SF90EX / SLV-SF90NP / SLV-SF90UX / SLV-SF90VC / SLV-SF99B / SLV-SF99EN / SLV-SF99NP / SLV-SF99UX / SLV-SF99VC Service Manual ▷ View online
SLV-SE85/SF90/SF99
3-5. AUDIO BLOCK DIAGRAM
3-17
3-18
IC360
#§
REC
650mVp-p
1
µ
sec/div
1
µ
sec/div
IC360
#¶
PB
80mVp-p
SLV-SE85/SF90/SF99
3-6. POWER BLOCK DIAGRAM (1)
3-19
3-20
3-21E
POWER BLOCK DIAGRAM (2)
SLV-SE85/SF90/SF99
4-1
SLV-SE85/SF90/SF99
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(For printed wiring boards)
•
•
b
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µµ
F.
50V or less are not indicated except for electrolytics and
tantalums.
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Be-
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
1
: fusible resistor
•
C
: panel designation
•
: internal component.
•
U
: B+ Line.
•
V
: B– Line.
• Circled numbers refer to waveforms.
• Readings are taken with a color-bar signal input.
• Voltage are dc between ground and measurement points.
• Readings are taken with a digital multimeter (DC10M
• Readings are taken with a color-bar signal input.
• Voltage are dc between ground and measurement points.
• Readings are taken with a digital multimeter (DC10M
Ω
).
• Voltage variations may be noted due to normal production
tolerances.
•
C
: adjustment for repair.
• Circled numbers refer to waveforms.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
C
B
E
5
6
4
2
1
3
5
4
6
2
3
1
4
5
2
3
1
1
2
4
5
3
3
2
1
3
2
1
3
2
1
Transistor
Diode
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
When indicating parts by reference
number, please include the board name.
number, please include the board name.
Note :
The components identified by
mark
The components identified by
mark
!
or dotted line with mark
!
are critical for safety.
Replace only with part number
specified.
specified.
Note :
Les composants identifiés par
une marque
Les composants identifiés par
une marque
!
sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Click on the first or last page to see other SLV-SE85B / SLV-SE85NP / SLV-SE85UX / SLV-SE85VC / SLV-SF90B / SLV-SF90EX / SLV-SF90NP / SLV-SF90UX / SLV-SF90VC / SLV-SF99B / SLV-SF99EN / SLV-SF99NP / SLV-SF99UX / SLV-SF99VC service manuals if exist.