Sony SLV-SE310D / SLV-SE310I / SLV-SE410K / SLV-SE510B / SLV-SE510D / SLV-SE510K Service Manual ▷ View online
– 2 –
SAFETY CHECK-OUT
1.
Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
dered connections. Check the entire board surface for solder
splashes and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly tran-
sistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
sistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
safety checks before releasing the set to the customer:
4.
Look for parts which, through functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
signs of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when solder-
ing or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
Maximum recording/playback time
10 hrs. in LP mode (with E300 tape)
Fast-forward and rewind time
Approx. 3 min. (with E180 tape)
Inputs and outputs
i LINE-1 (TV)
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
Video input: pin 20
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
DECODER/t LINE-2 IN
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Video input: pin 20
Audio input: pins 2 and 6
General
Power requirements
220 – 240 V AC, 50 Hz
Power consumption
18 W
1.5 W (POWER SAVE is set to ON,
minimum)
1.5 W (POWER SAVE is set to ON,
minimum)
Operating temperature
5
°
C to 40
°
C
Storage temperature
–20
°
C to 60
°
C
Dimensions
Approx. 355
×
96
×
288 mm (w/h/d)
including projecting parts and controls
Mass
Approx. 3.7 kg
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Design and specifications are subject to
change without notice.
change without notice.
– 3 –
TABLE OF CONTENTS
Section
Title
Page
Section
Title
Page
SERVICE NOTE ...................................................................... 4
1.
GENERAL
Getting Started .............................................................. 1-1
Basic Operations ........................................................... 1-10
Additional Operations .................................................... 1-15
Basic Operations ........................................................... 1-10
Additional Operations .................................................... 1-15
2.
DISASSEMBLY
2-1.
Upper Case Removal .................................................... 2-1
2-2.
Front Panel Section Removal ........................................ 2-1
2-3.
Power Block (ETXNY272E2D) Removal ....................... 2-1
2-4.
Rear Panel Removal ..................................................... 2-1
2-5.
Mechanism Deck Removal ........................................... 2-2
2-6.
MA-401 Board Removal ................................................ 2-2
2-7.
Internal Views ................................................................ 2-3
2-8.
Circuit Boards Location ................................................. 2-4
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram ................................................... 3-1
3-2.
Video Block Diagram ..................................................... 3-3
3-3.
Servo/System Control Block Diagram .......................... 3-5
3-4.
Audio/Tuner Block Diagram ........................................... 3-7
3-5.
Power Block Diagram .................................................... 3-9
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagram ............................................ 4-3
4-2.
Printed Wiring Boards and Schematic Diagrams ......... 4-5
MA-401 Printed Wiring Board ....................................... 4-5
MA-401 (Head Amp) Schematic Diagram .................... 4-9
MA-401 (Video, Audio) Schematic Diagram ................. 4-11
MA-401 (SECAM) Schematic Diagram ......................... 4-15
MA-401 (Servo/System Control)
Schematic Diagram ....................................................... 4-17
MA-401 (I/O) Schematic Diagram ................................. 4-21
MA-401 (Tuner) Schematic Diagram ............................ 4-23
MA-401 (Mode Control) Schematic Diagram ................ 4-25
MA-401 (Power Supply) Schematic Diagram ............... 4-27
KK-26 Schematic Diagram ............................................ 4-29
KK-26 Printed Wiring Board .......................................... 4-29
ETXNY272E2D Printed Wiring Board ........................... 4-30
ETXNY272E2D Schematic Diagram ............................ 4-31
MA-401 Printed Wiring Board ....................................... 4-5
MA-401 (Head Amp) Schematic Diagram .................... 4-9
MA-401 (Video, Audio) Schematic Diagram ................. 4-11
MA-401 (SECAM) Schematic Diagram ......................... 4-15
MA-401 (Servo/System Control)
Schematic Diagram ....................................................... 4-17
MA-401 (I/O) Schematic Diagram ................................. 4-21
MA-401 (Tuner) Schematic Diagram ............................ 4-23
MA-401 (Mode Control) Schematic Diagram ................ 4-25
MA-401 (Power Supply) Schematic Diagram ............... 4-27
KK-26 Schematic Diagram ............................................ 4-29
KK-26 Printed Wiring Board .......................................... 4-29
ETXNY272E2D Printed Wiring Board ........................... 4-30
ETXNY272E2D Schematic Diagram ............................ 4-31
5.
INTERFACE, IC PIN FUNCTION DESCRIPTION
5-1.
System Control-Video/RP Block Interface
(MA-401 BOARD IC162) ............................................... 5-1
(MA-401 BOARD IC162) ............................................... 5-1
5-2.
System Control-Servo Peripheral Circuit Interface
(MA-401 BOARD IC162) ............................................... 5-1
(MA-401 BOARD IC162) ............................................... 5-1
5-3.
System Control-Mechanism Block Interface
(MA-401 BOARD IC162) ............................................... 5-2
(MA-401 BOARD IC162) ............................................... 5-2
5-4.
System Control-System Control Peripheral Circuit
Interface (MA-401 BOARD IC162) ................................ 5-2
Interface (MA-401 BOARD IC162) ................................ 5-2
5-5.
System Control-Audio Block Interface
(MA-401 BOARD IC162) ............................................... 5-2
(MA-401 BOARD IC162) ............................................... 5-2
5-6.
Servo/System Control Microprocessor Pin Functions
(MA-401 BOARD IC162) ............................................... 5-3
(MA-401 BOARD IC162) ............................................... 5-3
5-7.
Mode Control Pin Functions
(MA-401 BOARD IC420) ............................................... 5-5
(MA-401 BOARD IC420) ............................................... 5-5
6.
ERROR CODES
....................................................... 6-1
7.
ADJUSTMENTS
7-1.
Mechanical Adjustments ............................................... 7-1
7-2.
Electrical Adjustments ................................................... 7-1
2-1.
Preparation Before Adjustments ................................... 7-1
2-1-1. Equipment Required ................................................ 7-1
2-1-2. Equipment Connection ............................................. 7-1
2-1-3. Set-up of Adjustment ............................................... 7-1
2-1-4. Alignment Tapes ....................................................... 7-1
2-1-5. I/O Level and Impedance ......................................... 7-2
2-1-6. Adjustment Sequence .............................................. 7-2
2-1-2. Equipment Connection ............................................. 7-1
2-1-3. Set-up of Adjustment ............................................... 7-1
2-1-4. Alignment Tapes ....................................................... 7-1
2-1-5. I/O Level and Impedance ......................................... 7-2
2-1-6. Adjustment Sequence .............................................. 7-2
2-2.
Power Supply Check ..................................................... 7-2
2-2-1. Output Voltage Check .............................................. 7-2
2-3.
Servo System Check ..................................................... 7-3
2-3-1. RF Switching Position Adjustment ........................... 7-3
2-4.
Audio System Adjustments ........................................... 7-3
2-4-1. Normal Audio System Adjustment ........................... 7-3
2-4-2. ACE Head Adjustment ............................................. 7-3
2-4-3. E-E Output Level Check ........................................... 7-3
2-4-4. Frequency Response Check .................................... 7-3
2-4-2. ACE Head Adjustment ............................................. 7-3
2-4-3. E-E Output Level Check ........................................... 7-3
2-4-4. Frequency Response Check .................................... 7-3
2-5.
Adjusting Parts Location Diagram ................................ 7-4
8.
REPAIR PARTS LIST
8-1.
Exploded Views ............................................................. 8-1
8-1-1. Front Panel and Cabinet Assemblies ....................... 8-1
8-1-2. Chassis Assembly .................................................... 8-2
8-1-3. Mechanism Chassis Assembly (1) ........................... 8-3
8-1-4. Mechanism Chassis Assembly (2) ........................... 8-4
8-1-5. Mechanism Chassis Assembly (3) ........................... 8-5
8-1-2. Chassis Assembly .................................................... 8-2
8-1-3. Mechanism Chassis Assembly (1) ........................... 8-3
8-1-4. Mechanism Chassis Assembly (2) ........................... 8-4
8-1-5. Mechanism Chassis Assembly (3) ........................... 8-5
8-2.
Electrical Parts List ....................................................... 8-6
– 4 –
SERVICE NOTE
1. DISASSEMBLY
• This set can be disassembled in the order shown below.
Note:
Pages in indicated pages in the SERVICE MANUAL.
Pages in indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI.
Pages in indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI.
Set
Upper Case
(Page 2-1)
(Page 2-1)
Front Panel
Section
(Page 2-1)
Power Block
(ETXNY272E2D)
(Page 2-1)
Pinch Press
Block Ass’y
(Page 14)
Ground Shaft
Ass’y
(Page 13)
Mechanism
Deck
(Page 2-2)
FL Complete
Ass’y
(Page 13)
Drum
Ass’y
Ass’y
(Page 13)
Rear
Panel
(Page 2-1)
Rubber
Belt
(Page 15)
Rubber
Belt
(Page 15)
Slider
(Page 26)
Loading
Gear (T, S)
(Page 28)
Retainer
Plate
(Page 22)
Rubber
Belt
(Page 15)
Capstan
Motor
(Page 15)
FL Slider
Block Ass’y
(Page 22)
Pully Gear
Ass’y
(Page 29)
Cam Motor
Retainer
(Page 31)
Cam Gear
(Page 23)
Cam Motor
(Page 31)
Reel Direct
Ass’y
(Page 30)
MA-401
Board
(Page 2-2)
Rotary
Switch
Switch
Tuner
Unit
1-1
SECTION 1
GENERAL
This section is extracted from SLV-
SE410K/SE510K instruction manual.
(3-065-673-11)
SE410K/SE510K instruction manual.
(3-065-673-11)
SLV-SE310/SE410/SE510
4
Index to parts and controls
Getting Started
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel
A ?/1 (on/standby) switch (17)
B A (eject) button (42)
C Tape compartment
D Remote sensor (10)
E m (rewind) button (42) (60)
F H (play) button (42) (60)
G M (fast-forward) button (42) (60)
H z REC (record) button (44) (61)
(75)
* SLV-SE510K only
I x (stop) button (42) (75)
J X (pause) button (42) (75)
K
DIAL TIMER (48)
L SYNCHRO REC (Synchronized
Recording) button* (63)
M PROGRAM +/– buttons (20) (60)
(69)
N AUTO SET UP/
RF (Radio Frequency) CHANNEL
button (17) (20)
button (17) (20)
Getti
ng Sta
rted
5
Index to parts and controls
Display window
A Timer indicator (50) (54) (58)
B Tape speed indicators (44)
C VIDEO indicator (14) (45)
D VPS (Video Programme System)/
PDC (Programme Delivery Control)
indicator* (55)
indicator* (55)
E OPC (Optimum Picture Control)
indicator (69)
* SLV-SE510K only
F SMARTLINK indicator* (15)
G TV indicator* (46)
H Tracking indicator (69)
I Time counter/clock/line/programme
position indicator (42) (44) (75)
J Remaining time indicator (45)
K Tape/recording indicator (44)
LP
EP
EP
SMARTLINK
VIDEO VPS
SP
PDC
OPC
TV
continued
6
Index to parts and controls
Rear panel
A Mains lead (13) (14)
B AERIAL IN
ANTENNE ENTREE connector (13)
(14)
(14)
C AERIAL OUT
ANTENNE SORTIE connector (13)
(14)
(14)
D DECODER/t LINE-2 IN
DECODEUR/t ENTREE LIGNE-
2 connector (16) (37) (62) (74)
2 connector (16) (37) (62) (74)
E i LINE-1 (TV)
i LIGNE-1 (TV) connector (14)
(37)
(37)
Getti
ng Sta
rted
7
Index to parts and controls
Remote commander
A Z EJECT button (42)
B COUNTER/REMAIN button (45)
C CLEAR button (42) (53) (64)
D SP (Standard Play)/LP (Long Play)
button (44)
E Programme number buttons (11) (45)
F - (ten’s digit) button (11) (45)
G 2 (volume) +/– buttons (for TV)
(11)
H z REC (record) button (44) (61)
I
TIMER button (53) (57)
J MENU button (23) (64)
K X PAUSE/M button (23) (42)
x STOP/m button (23) (42)
m
m
REW (rewind)/< button
(42) (60)
M
M
FF (fast-forward)/, button
(42) (60)
H PLAY/OK button (23) (42)
H PLAY/OK button (23) (42)
1
2
3
4
5
6
7
8
9
0
continued