DOWNLOAD Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW Service Manual ↓ Size: 16.1 MB | Pages: 75 in PDF or view online for FREE

Model
SLV-ED22KR SLV-ED22PL SLV-ED22TW SLV-ED55KR SLV-ED55PL SLV-ED88TW SLV-ED99KR SLV-ED99PL SLV-ED99TW
Pages
75
Size
16.1 MB
Type
PDF
Document
Service Manual
Brand
Device
VCR
File
slv-ed22kr-slv-ed22pl-slv-ed22tw-slv-ed55kr-slv-ed.pdf
Date

Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW Service Manual ▷ View online

– 4 –
SERVICE  NOTE
1. DISASSEMBLY
• This set can be disassembled in the order shown below.
Note:
Pages in          indicated pages in the SERVICE MANUAL.
Pages in          indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI.
Set
Upper case
(Page 2-1)
Front Panel
Section
(Page 2-1)
PSM17-501
Board
(Page 2-1)
Pinch Press
Block Ass’y
(Page 14)
Ground Shaft
Ass’y
(Page 13)
Mechanism
Deck
(Page 2-2)
FL Complete
 Ass’y
(Page 13)
Drum
Ass’y
(Page 13)
Rear
Panel
(Page 2-1)
RF-048
Board
(Page 2-2)
Rubber
Belt
(Page 15)
Rubber
Belt
(Page 15)
Slider
(Page 26)
Loading
Gear (T, S)
(Page 28)
Retainer
 Plate
(Page 22)
Rubber
Belt
(Page 15)
Capstan
Motor
(Page 15)
FL Slider
 Block Ass’y
(Page 22)
Pully Gear
Ass’y
(Page 29)
Cam Motor
Retainer
(Page 31)
Cam Gear
(Page 23)
Cam Motor
(Page 31)
Reel Direct
Ass’y
(Page 30)
MA-377
Board
(Page 2-2)
Rotary
Switch
(Page 2-2)
Tuner
Unit
1-1
SECTION  1
GENERAL
This section is extracted from SLV-
ED22KR/ED55KR/ED99KR instruction
manual. (3-058-932-11)
SLV-ED22/ED55/ED88/ED99
Getting Started
4
Getting Started
Step 1
Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• Size AA (R6) batteries
• 75-ohm coaxial cable with F-type
connectors
• Plug adaptor
Checking your model name
The instructions in this manual are for the 3 models: SLV-ED99PL,
ED55PL and ED22PL.  Check your model number by looking at the
rear panel of your VCR. SLV-ED99PL is the model used for illustration
purpose. Any difference in operation is clearly indicated in the text,
for example,“SLV-ED22PL only.”
5
Getting Started
Getting Started
Inserting the batteries
Insert two size AA (R6) batteries by
matching the + and – on the batteries
to the diagram inside the battery
compartment.
Insert the negative (–) end first, then
push in and down until the positive
(+) end clicks into position.
Using the remote commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with
a dot (•) can be used to operate
your Sony TV. If the TV does not
have the g symbol near the
remote sensor, this remote
commander will not operate the
TV.
Step 2
Setting up the remote commander
To operate
the VCR
a Sony TV
Set  TV / VIDEO  to
 VIDEO  and point at the remote sensor on the VCR
 TV  and point at the remote sensor on the TV
Remote sensor
TV
/
VIDEO
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
1
2
3
continued
Getting Started
6
Controlling other TVs with the remote commander
(SLV-ED99PL only)
The remote commander is preprogrammed to control non-Sony TVs.  If your
TV is listed in the table below, set the appropriate manufacturer’s code
number.
1
Set  TV / VIDEO  at the top of the remote commander to  TV .
2
Hold 
?/1 down, and enter your TV’s code number(s) using the number
buttons.  Then release 
?/1.
Now you can use the 
?/1, VOL +/–, CH +/– and TV/VIDEO buttons to
control your TV.  You can also use the buttons marked with a dot (
) to
control a Sony TV.  To control the VCR, reset  TV / VIDEO  to  VIDEO .
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
Step 2: Setting up the remote commander (continued)
Notes
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• You may not be able to use some buttons to control non-Sony TVs due to the remote
commander’s signal limitations.
• If you enter a new code number, the code number previously entered will be erased.
• When you replace the batteries of the remote commander, the code number  may
automatically reset to 01 (Sony).  If your TV is not a Sony, it is recommended to
manually set the appropriate code number every time you replace the batteries.
Manufacturer
Sony
Akai
AOC
Centurion
Colonad
Curis-Mathes
Emerson
Fisher
General Electric
Gold Star
Hitachi
JVC
Magnavoc
Marantz
Code number
01
04
04
12
03
12
03, 04, 14
11
06, 10
03, 04, 17
02
09
08
13
Manufacturer
MGA/Mitsubishi
Panasonic
Philips
Pioneer
Quasar
Radio Shack
RCA
Sanyo
Sears
Sharp
Sylvania
Teknika
Toshiba
Zenith
Code number
13
06, 19
08
16
06
05, 14
10
11
07, 11
05, 18
08
14
07
15
7
Getting Started
Getting Started
Step 3
Hookup
Audio/video (A/V) hookup
If your TV has audio/video (A/V) input jacks, you will get a better picture
and sound when you hook up your VCR using these connections. If your TV
doesn’t have A/V inputs, see the following page for antenna hookup.
For SLV-ED99PL only
For a true “home theater” experience, you should connect the audio outputs
of your VCR or TV to your stereo system.
A  Use this hookup if your TV has stereo jacks
B  Use this hookup if your TV doesn’t have stereo jacks
VCR
Stereo receiver
Audio/video cable (not supplied)
TV
TV
VCR
Stereo receiver
Video cable (not supplied)
Audio cable (not supplied)
Audio cable (not supplied)
IN
VIDEO
AUDIO
AUDIO OUT
AUX IN
AUDIO VIDEO
LINE-2 
OUT
LINE-1 
OUT
VIDEO
AUDIO
IN
AUX IN
AUDIO VIDEO
LINE-2 
OUT
LINE-1 
OUT
TV
VCR
Stereo receiver
Video cable (not supplied)
Audio cable (not supplied)
VIDEO
AUDIO
IN
AUX IN
AUDIO VIDEO
LINE-2 
OUT
LINE-1 
OUT
or
continued
1-2
Getting Started
8
Step 3: Hookup (continued)
Notes
• To listen to playback sounds in stereo, you must use the A/V connection.
• If you use the Trinitron TV Synchro Play function (see page 22), the A/V connection
is necessary. (If your TV has two or more inputs, connect the audio/video cable to
the VIDEO IN 1 jacks.)
• You can improve sound quality by connecting a stereo system to LINE-2 OUT jacks
using audio cable (not supplied).
For SLV-ED55PL and ED22PL only
A  Use this hookup if your TV has stereo jacks
B  Use this hookup if your TV doesn’t have stereo jacks
VCR
Audio/video cable (not supplied)
TV
Note
• If you use the Trinitron TV Synchro Play function (see page 22), the A/V connection
is necessary. (If your TV has two or more inputs, connect the audio/video cable to
the VIDEO IN 1 jacks.)
TV
VCR
Audio/video cable (not supplied)
IN
VIDEO
AUDIO
AUDIO VIDEO
LINE-1 IN
LINE-1 OUT
VIDEO
AUDIO
IN
AUDIO VIDEO
LINE-1 IN
LINE-1 OUT
9
Getting Started
Getting Started
Antenna hookup
Make the following connections when you’re using an antenna.
Use this hookup if you’re using:
• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
Use this hookup if you’re using a VHF-only antenna (you get
channels 2–13 only)
or
or
Match the type of
connector on your
TV: A, B, or C.
A
B
C
UHF
VHF
A
or
or
Match the type of
connector on your
TV: A, B, or C.
B
For connector
types B and C, no
UHF connection is
required.
C
UHF
VHF
VCR
UHF
VHF
UHF
VCR
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external
antenna connector (not supplied) so you can connect the cable to the VHF/UHF IN
connector. If you have separate cables for VHF and UHF antennas, you should use a
U/V band mixer (not supplied). For details, see page 52.
VHF
IN
OUT
VHF/UHF
Rear of TV
VHF/UHF
Rear of TV
VHF/UHF
IN
OUT
VHF/UHF
continued
Getting Started
10
TV/VIDEO
?/1
Number
buttons,
ENTER
1
Set the RF UNIT switch on the rear of the VCR to CH3 or CH4,
whichever channel is not used in your area. If both are used, set the
switch to either channel.
2
Press 
?/1 (power) to turn on the VCR.
3
Press TV/VIDEO on the remote commander to turn on the VIDEO
indicator in the VCR’s display window.
4
Press CH +/– to display a channel number in the display window.
Select an active channel number in your area.
5
Turn on your TV and set it to the channel you selected in step 1
(channel 3 or 4).
The channel you selected in step 4 appears on the TV screen. If the
channels change when you press CH +/–, you have made the
correct setting.
Whenever you use the VCR, set the TV to the channel selected in
step 1.
Setting the RF unit
When connecting the VCR to the TV
using only the antenna cable, you must
set the RF UNIT switch on the rear of the
VCR so that the TV can receive the
correct signal from the VCR.
If you made A/V connections (pages 7
or 8) you can skip this step.
CH +/–
• CH
• TV/ 
 VIDEO
RF UNIT
CH3
RF UNIT
CH4
• 
]/1
1
2
3
4
5
6
7
8
9
0
Step 3: Hookup (continued)
11
Getting Started
Getting Started
PLAY
OK
1
Press MENU, then press 
M/m to move the
cursor (
B) to CLOCK SET, then press OK.
2
Press 
M/m to set the month.
3
Press 
, to flash the day and press M/m
to set the day.
The day of the week is set automatically.
Step 4
Setting the clock
You must set the time and date on the
VCR to be able to use the timer
recording features properly.
Before you start...
• Turn on the VCR and the TV.
• Set the TV to the VCR channel
(channel 3 or 4). If your TV is
connected to the VCR using A/V
connections, set the TV to video input.
• Press TV/VIDEO to display the
VIDEO indicator in the VCR’s display
window.
MENU
OK
M/m/</,
MENU  
PLAY
OK
CLOCK SET
1 1 / 2 0 0 0
SAT
12 : 0 0 AM
SET
SELECT
: [
]
END
: [ OK ]
: [
]
PLAY
OK
CLOCK SET
1 1 / 1 / 2 0 0 0
WED
12 : 0 0 AM
SET
SELECT
: [
]
END
: [ OK ]
: [
]
CLOCK SET
1 1 / 1
/ 2 0 0 0 THU
12 : 0 0 AM
6
SET
SELECT
: [
]
END
: [ OK ]
: [
]
continued
1-3
Getting Started
12
4
Set the year, hour and minutes in
sequence, using / to flash the item to be
set, and >/. to select the digits.
5
Press OK to start the clock.
Tip
• To change the digits during setting, press 
< to return to the item to be changed,
and select the digits using >/..
Note
• The menu disappears automatically if you don’t proceed for more than a few
minutes.
PLAY
OK
PLAY
OK
AM
CLOCK SET
1 1 / 1
/ 2 0 0 0 THU
12 : 3 0
6
SET
SELECT
: [
]
END
: [ OK ]
: [
]
Step 4: Setting the clock (continued)
13
Getting Started
Getting Started
SP
APC
Step 5
Press and hold ONE TOUCH TUNING on the VCR for more than
three seconds.
The VCR starts presetting the channels.
The WAIT indicator goes off when all receivable channels are preset.
To check if the channels are preset correctly
Set the TV to the video channel and press CHANNEL +/– on the VCR.
If the TV screen changes to a different program each time you press
CHANNEL +/–, the channels are preset correctly.
Tip
• To stop the One Touch Tuning function, press ONE TOUCH TUNING or 
p STOP
on the VCR during the setting.
ONE TOUCH
TUNING
Presetting channels
First, we recommend that you preset the receivable channels in your area
using the One Touch Tuning function or the AUTO PRESET in the TUNER
PRESET menu. Then, if some channels could not be preset automatically, set
them manually; if there are any unwanted channels among the preset ones,
you can disable the channels.
Presetting all receivable
channels using the One
Touch Tuning function
CHANNEL +/–
ONE TOUCH
TUNING
continued
Getting Started
14
Step 5: Presetting channels (continued)
Presetting all receivable
channels automatically
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the VCR channel
(channel 3 or 4). If your TV is
connected to the VCR using A/V
connections, set the TV to video input.
• Press TV/VIDEO to display the
VIDEO indicator in the VCR’s display
window.
1
Press MENU, then press 
M/m to move the
cursor (
B) to TUNER PRESET, then press
OK.
2
Press 
M/m to select ANTENNA/CABLE.
MENU
OK
M/m/</,
MENU  
PLAY
OK
TUNER PRESET
1
CH
ANTENNA / CABLE
AUTO PRESET
MANUAL SET
AFT
SET
SELECT
FINE TUNING
ANT
ADD
ON

CABLE
ERASE
OFF
: [
]
: [
]
PLAY
OK
15
Getting Started
Getting Started
3
• To preset cable TV channels:
Press 
</, to set ANTENNA/CABLE
to CABLE.
• To preset VHF and UHF channels:
Press 
</, to set ANTENNA/CABLE
to ANT.
4
Press 
M/m to move the cursor (B) to
AUTO PRESET, then press OK.
All receivable channels are preset in
numerical sequence. When no more
receivable channels can be found,
presetting stops and the picture from the
lowest numbered channel is displayed on
the TV screen.
TUNER PRESET
2
CH
ANTENNA / CABLE
AUTO PRESET
MANUAL SET
AFT
SET
SELECT
FINE TUNING
ANT
ADD
ON

CABLE
ERASE
OFF
: [
]
: [
]
TUNER PRESET
2
CH
ANTENNA / CABLE
AUTO PRESET
MANUAL SET
AFT
ANT
ADD
ON

CABLE
ERASE
OFF
PLEASE WAIT
FINE TUNING
PLAY
OK
PLAY
OK
PLAY
OK
TUNER PRESET
1
CH
ANTENNA / CABLE
AUTO PRESET
MANUAL SET
AFT
SET
SELECT
FINE TUNING
ANT
ADD
ON

CABLE
ERASE
OFF
: [
]
: [
]
continued
Page of 75
Display

Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW Service Manual ▷ Download

  • DOWNLOAD Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW Service Manual ↓ Size: 16.1 MB | Pages: 75 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW in PDF for free, which will help you to disassemble, recover, fix and repair Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW VCR. Information contained in Sony SLV-ED22KR / SLV-ED22PL / SLV-ED22TW / SLV-ED55KR / SLV-ED55PL / SLV-ED88TW / SLV-ED99KR / SLV-ED99PL / SLV-ED99TW Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.