DOWNLOAD Sony SLV-D940PAZ / SLV-D940PEA / SLV-D940PME Service Manual ↓ Size: 12.55 MB | Pages: 122 in PDF or view online for FREE

— 9 —

The laser diode in the optical pick up may suffer electrostatic
breakdown because of potential static electricity from clothing and
your body.

The following method is recommended.
(1) Place a conductive sheet on the work bench (The black sheet used

for wrapping repair parts.)

(2) Place the set on the conductive sheet so that the chassis is grounded

to the sheet.

(3) Place your hands on the conductive sheet (This gives them the

same ground as the sheet.)

(4) Remove the optical pick up block

(5) Perform work on top of the conductive sheet. Be careful not to let

your clothes or any other static sources to touch the unit.

◆ Be sure to put on a wrist strap grounded to the sheet.
◆ Be sure to lay a conductive sheet made of copper etc. Which is

grounded to the table.

Fig.3

(6) Short the short terminal on the PCB, which is inside the Pick-Up

ASS’Y, before replacing the Pick-Up. (The short terminal is shorted
when the Pick-Up Ass’y is being lifted or moved.)

(7) After replacing the Pick-up, open the short terminal on the PCB.

THE UNIT

WRIST-STRAP
FOR GROUNDING

1M

1M

CONDUCTIVE SHEET

— 10 —

1) Remove the power cord.
2) Disassemble the Deck-Assy.
3) Make solder land 2 points short on Pick-up.

(See Fig. 4)

4) Disassembly the Pick-up.

1) Replace the Pick-up.
2) Remove the soldering 2 points on Pick-up.
3) Reassemble the Deck-Assy.

 If the assembly and disassembly are not done in correct  sequence, the Pick-up may be damaged.

SOLDER LAND 2 POINTS SHORT

Fig. 4

1-1

8

Unpacking

Check that you have received the following items with the DVD-VCR: 

Note
• The  supplied remote commander is for the exclusive use of this DVD-VCR.  

• Remote commander

• Aerial cable

• R6  (size  AA) batteries

• Audio cord 

(pinplug ×2 y pinplug ×2)

• Video  cord 

(pinplug ×1 y pinplug ×1)

The instructions in this manual are for the 3 models: SLV-D940P AZ, SLV-D940P ME and 

SLV-D940P EA.  Check your model name by looking at the rear panel of your DVD-VCR.

SLV-D940P AZ is the model used for illustration purposes.  Any difference in operation is 

clearly indicated in the text, for example, “SLV-D940P AZ only.”

9

Setting up the remote commander

Notes
• With normal use, the batteries should last about three to six months.
• If  you do not use the remote commander for an extended period of time, remove the batteries 

to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.
• Do not use different types of batteries.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus.  Doing so 

may cause a malfunction.

Insert two size AA (R6) batteries 

by matching the + and – on the 

batteries to the diagram inside the 

battery compartment.
Insert the negative (–) end first, 

then push in and down until the 

positive (+) end clicks into 

position.

You can use this remote 

commander to operate this DVD-

VCR and a Sony TV.  Buttons on 

the remote commander marked 

with a dot (•) can be used to 

operate your Sony TV. 
If the TV does not have the   

symbol near the remote sensor, this 

remote commander will not 

operate the TV.

the DVD player

DVD·VIDEO, then press SELECT DVD and point at the remote sensor at 

the DVD-VCR

the VCR

DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor 

at the DVD-VCR

your TV

TV and point at the remote sensor at your TV

10

Setting up the remote commander

The remote commander is preprogrammed to control non-Sony TVs.  If your TV is 

listed in the following table, set the appropriate manufacturer’s code number.

Now you can use the ?/1, VOL +/–, PROG +/–, MUTING*, TV/VIDEO, 0-9 and 

-/--* buttons to control your TV.  You can also use the buttons marked with a dot (•) to 

control a Sony TV.  To control the DVD-VCR, reset TV / DVD·VIDEO to 

DVD·VIDEO.

* for  Sony TV only

Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find 

the one that works with your TV.

Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the 

DVD-VCR, you cannot control your TV with the remote commander.

• When you replace the batteries of the remote commander, the code number may change.  Set 

the appropriate code number every time you replace the batteries.

Set TV / DVD·VIDEO at the top of the remote commander to TV.

Hold down ?/1, and enter your TV’s code number using the number buttons.  

Then release ?/1.

Sony

01, 02

Akai

68

Ferguson

52

Grundig

10, 11

Hitachi

24

JVC

33

Loewe

45

Mivar

09, 70

NEC

66

Nokia

15, 16, 69

Panasonic

17, 49

Philips

06, 07, 08

Saba

12, 13

Samsung

22, 23

Sanyo

25

Sharp

29

Telefunken

36

Thomson

43

Toshiba

38

11

Connecting the DVD-VCR

Note that “Advanced Hookups” (page 54) explains additional hookup methods that 

will optimize the picture and sound for a true “hometheatre” experience.

Note
• When you connect the DVD-VCR and your TV only with an aerial cable, you have to tune 

your TV to the DVD-VCR (see page 13).

Disconnect the aerial cable from your TV 
and connect it to   on the rear panel of the 

DVD-VCR.

Connect  

of the DVD-VCR and the 

aerial input of your TV using the supplied 

aerial cable.

Connect the mains lead to the mains.

This section is extracted from instruction manual.
(2-109-228-11)

1-2

12

Connecting the DVD-VCR

video input jacks
This additional connection 

improve picture and sound 

quality.  Connect the TV as 

shown on the right.

13

Setting up the DVD-VCR with the Auto Set Up function

Before using the DVD-VCR for the first 

time, set up the DVD-VCR using the Auto 

Set Up function.  With this function, you can 

set TV channels automatically. 

Before you start…
• To control the DVD-VCR, set TV / 

DVD·VIDEO to DVD·VIDEO on the 

remote (page 9).

Turn on your TV and set it to the video channel.
Tune the TV to channel 68 (in Australia), channel 63 (in New Zealand) or 

channel 32 (the initial RF channel for this DVD-VCR).  Refer to your TV 

manual for TV tuning instructions.  If the picture does not appear clearly, 

see “To change the RF channel” on page 15.

V/v/B/b
ENTER

14

Setting up the DVD-VCR with the Auto Set Up function

To cancel the Auto Set Up function
Press SET UP.

Connect the mains lead to the mains.
SLV-D940P AZ
The DVD-VCR automatically turns on and the 

“SYSTEM SELECTION” menu appears.
Step 3 is skipped.

SLV-D940P ME/EA
The DVD-VCR automatically turns on and the 

“LANGUAGE SET” menu appears.
Press V/v to select the desired language, then 

press ENTER.
The message for the Auto Set Up function 

appears.

Press ENTER.
The “SYSTEM SELECTION” menu appears.

Press V/v to select the appropriate TV system, 

then press ENTER.

The DVD-VCR starts searching for all of the 

receivable channels and presets them (in the 

appropriate order for your local area).
If you want to change the order of the channels 

or disable unwanted programme positions, see 

“Changing/disabling programme positions” on page 23.
After the search is complete, the clock setting menu appears.  See “Setting 

the clock” on page 17.

ENTER

RETURN

SYSTEM SELECTION

SET UP

ENTER

v

V

SYSTEM - B/G (NEW ZEALAND)
SYSTEM - B/B (AUSTRALIA)

RETURN

LANGUAGE SET

SET UP

ENTER

v

V

English
Français
Deutsch

B

Español
Italiano
Nederlands

ENTER

RETURN

SYSTEM SELECTION

SET UP

ENTER

v

V

SYSTEM - B/G
SYSTEM - D/K
SYSTEM - I

ENTER

Please wait

RETURN

AUTO SETUP

SET UP

10%

15

Setting up the DVD-VCR with the Auto Set Up function

To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on the DVD-

VCR and TV.  Select “Install” in the “OPTION” menu, then press V/v to select 

“Video Output CH.”  Select the RF channel by pressing the B/b buttons and press 

ENTER.  Then, tune the TV to the new RF channel so that a clear picture appears.

Tip
• If you want to change the language for the on-screen display from the one preset in the Auto 

Set Up function, see page 16.

Notes
• Whenever you operate the Auto Set Up function, some of the settings (timer etc.) will be 

reset.  If this happens, you have to set them again.

• Auto preset starts automatically only when you plug in the mains lead for the first time after 

you purchase the DVD-VCR.

• If  you want to use the Auto Set Up function again, select “Install” in the “OPTION” menu, 

then press V/v to select “Auto Setup,” then repeat step 3.

• Auto preset can be performed by pressing x on the unit continuously for 5 seconds or more 

during power off with no tape inserted.

• The Line Through function will not operate properly if “Power Save” in “OPTION” menu is 

set to “On.”  Set “Power Save” to “Off” to ensure proper operation.