Sony SLV-798HF / SLV-998HF Service Manual ▷ View online
— 5 —
2-4-2. SYNC AGC Check (MA-318 Board) ······························ 6-4
2-4-3. Recording Y Level Check (MA-318 Board) ··················· 6-4
2-4-4. Recording Chroma Level Check (MA-318 Board) ········· 6-5
2-4-5. Playback Level Check (MA-318 Board) ························· 6-5
2-5.
2-4-3. Recording Y Level Check (MA-318 Board) ··················· 6-4
2-4-4. Recording Chroma Level Check (MA-318 Board) ········· 6-5
2-4-5. Playback Level Check (MA-318 Board) ························· 6-5
2-5.
AUDIO SYSTEM ADJUSTMENT ································· 6-5
2-5-1. ACE Head Adjustment ···················································· 6-5
2-5-2. E-E Output Level Check ················································· 6-5
2-5-3. Overall Output Level and Distortion Factor Check ········· 6-6
2-5-4. Overall Noise Level Check ·············································· 6-6
2-6.
2-5-2. E-E Output Level Check ················································· 6-5
2-5-3. Overall Output Level and Distortion Factor Check ········· 6-6
2-5-4. Overall Noise Level Check ·············································· 6-6
2-6.
TUNER SYSTEM ADJUSTMENT ································ 6-6
2-6-1. Separation Adjustment (MA-318 Board) ························ 6-6
2-7.
2-7.
ADJUSTING PARTS LOCATION DIAGRAM ············· 6-8
7.
REPAIR PARTS LIST
7-1.
EXPLODED VIEWS ······················································ 7-1
7-1-1. FRONT PANEL ASSEMBLY AND UPPER CASE
SECTION ········································································ 7-1
7-1-2. CHASSIS SECTION ······················································· 7-2
7-1-3. MECHANISM DECK-1 ················································· 7-3
7-1-4. MECHANISM DECK-2 ················································· 7-4
7-1-5. MECHANISM DECK-3 ················································· 7-5
7-2.
7-1-3. MECHANISM DECK-1 ················································· 7-3
7-1-4. MECHANISM DECK-2 ················································· 7-4
7-1-5. MECHANISM DECK-3 ················································· 7-5
7-2.
ELECTRICAL PARTS LIST ·········································· 7-6
— 6 —
1. ERROR CODE INDICATION
• Error codes are indicated using the lower 5 digits in the fluorescent display tube.
“At this time, Colon “:” between character is not indicated.”
ERROR CODE
MODE CODE
0
Power-on eject
10 FWD x1
20 REW play
1
Power-on initial
11 FWD x2
21 Cas. loading
2
Power-off eject
12 CUE
22 Tape loading
3
Power-off stop
13 PB-pause
23 Power-off loading
4
FF
14 RVS-pause
24 Mecha. error (Power on)
5
REW
15 RVS x1
25 Power-on eject initial
6
REC
16 RVS x2
26 Power-off eject initial
7
REC- pause
17 REV
27 APC REC
8
Power-on stop
18 Power-off initial
28 Cas. loading
9
PB
19 Mecha. error (Power off)
(No auto PB check)
0
No error
1
Cam encoder error Loading direction
2
Cam encoder error Unloading direction
3
T reel error
4
S reel error
5
Capstan error
6
Drum error
7
Error on initializing
8
Cassette loading error
9
Reserve
Mode code indication when the error has occurred.
Error code
SLV-798HF/998HF
SERVICE NOTE
— 7 —
2.
HOW TO REPLACE A ROTARY
UPPER DRUM
UPPER DRUM
See below for note.
2-1.
HOW TO REMOVE A ROTARY UPPER DRUM
1)
Remove screw 1 (+P3
×
8) and remove the ground shaft
assembly 2. (Refer to Fig. 4.)
2)
Remove soldering which is marked by arrow and remove the
rotary upper drum board completely.
rotary upper drum board completely.
3)
Remove two screws 3 (PSW3
×
8) and remove the rotary
upper drum in the direction of A. (Refer to Fig. 5.)
If removal is difficult, remove it while rotating it slowly.
If removal is difficult, remove it while rotating it slowly.
Note:
If removal is difficult, check again if soldering is removed
completely.
completely.
Fig. 4
2-2.
HOW TO ATTACH A NEW ROTARY UPPER
DRUM
DRUM
1)
Pay attention so that finger print or like must not be put when
inserting a new upper drum into lower drum.
inserting a new upper drum into lower drum.
2)
Align mark of the rotary upper drum board with the mark of
the rotary transformer board so that the screw hole on the upper
drum and that on the lower drum are aligned. (Refer to Fig. 5.)
the rotary transformer board so that the screw hole on the upper
drum and that on the lower drum are aligned. (Refer to Fig. 5.)
3)
If attaching is difficult, attach a upper drum while rotating it
slowly.
slowly.
Note:
Pay attention not to damage the video heads.
Confirm that the upper drum is inserted completely.
Confirm that the upper drum is inserted completely.
4)
Tighten the two screws 3 (PSW3
×
8). (Refer to Fig. 5.)
5)
Fix the earth shaft 2 by tightening the screw 1 (+P3
×
8) so
that protrusion at the tip of the earth shaft contacts the center
of the drum shaft.
of the drum shaft.
Note:
When attaching the ground shaft assembly 2, never give
force to the plate spring 4.
Fig. 5
1
Screw (+P3
×
8)
2
Ground shaft assembly
Drum when viewed
from the top
from the top
Soldering
4
Plate
spring
Soldering
3
PSW3
×
8
Upper drum assembly
DZR-51-R (8-848-594-02)
(998HF)
DZR-45-R (8-848-576-02)
(EXCEPT 998HF)
DZR-51-R (8-848-594-02)
(998HF)
DZR-45-R (8-848-576-02)
(EXCEPT 998HF)
Align the two arrow marks.
A
Lower drum assembly
DZL-51B/J-RP (8-848-666-11)
DZL-51B/J-RP (8-848-666-11)
Note : There are two types of drum assembly built in models.
[Discrimination]
There are two printed circuit boards
on the top.
on the top.
UPPER DRUM ASSEMBLY
DZR-51-R (998HF)
(8-848-594-02)
DZR-45-R (Except 998HF)
(8-848-576-02)
—Top View—
There is no printed circuit board.
DRUM ASSEMBLY
DZH-96A-R (998HF)
(8-839-046-02)
DZH-94A/Z-RP (Except 998HF)
(8-839-044-02)
—Top View—
Note:
It cannot be divided to two parts, the upper and
the lower drum assemblies.
the lower drum assemblies.
1-1
SLV-798HF/998HF
SECTION 1
GENERAL
This section is extracted from the
SLV-998HF instruction manual.
SLV-998HF instruction manual.
Click on the first or last page to see other SLV-798HF / SLV-998HF service manuals if exist.