DOWNLOAD Sony KV-XG29M8J Service Manual ↓ Size: 15.39 MB | Pages: 67 in PDF or view online for FREE

– 33 –

Item

M

1

D/K

1

I

1

B/G

1

2nd. Lang

1

SECAM

1

XTAL 3.58

1

XTAL 4.43

1

Item

Color SW

0

11 KEY

0

AV Mono

0

US ST

0

Auto TV sys

0

Auto PIC

0

2199 Curve

0

PIC Rotate

0

Item

1

0

DVD Input

0

Dis Fav.

0

Thai Bil

0

HDEV

0

NICAM

0

TOP

0

AV Input

When bit 7.6 & 5 = 000, Only PAL color system is selected.
When bit 7 is selected, Auto, PAL & NTSC 4.43 Color is enable
When option is single color system. Color system cannot be changed & "AUTO" will not be displayed.

AV Input

00 = no AV Input

01 = 1 AV Input

10 = 2 AV Input

11 = 2AV Input

DVD Input

Effective only when "AV Input" is set to 3 AV Inout.

Dis Fav.

Disable favourite channel ( Only Effective For 21" & 14" Models Only)

Pic Rot 

–1

Picture Rotation Feature Switch

0 = disabled,

1 = enabled

2199 Curve 

–1

 

2199 Volume Curve Selection

0 = Others,

1 = 2199 Volume Curve

Auto PIC

Auto Picture Improvement

0 = Initiative,

1 = active

A-TVsys

Auto TV system in Auto Program

0 = disabled,

1 = enabled

US ST

USA Stereo

0 = disabled,

1 = enabled

AV Mono 

–1

AV Mono models

0 = Stereo,

1 = Mono ( No Balance &

Surround selection)

11 Key

Front Key Selection

0 = 7 key model

1 = 11 Key model

Color SW 

–2

Color Data Selection in Dynamite Mode

0 = 65 (No. PIP)

1 = 57 (PIP)

Note

*1 - For XF-L (21" & 14") Models Only
*2 - For XF-H (25", 29" & 34") Models Only

– 34 –

1. Select Video 1.

2. Input a NTSC color-bar, video into Video 1.

3. Set the following condition:

PICTURE 100%, BRIGHTNESS 50%, COLOR 50%

4. Connect an oscilloscope to pin 1 (B OUT) of CN305, A board.

5. Select SAJ 1 ‘SHU’ with 1 and 4 of the commander by set-

ting to Service Mode and adjust to VB1=VB2=VB3=VB4 with
3 and 6.

1. Input a PAL color-bar.

2. Set to the following condition:

PICTURE 100%, BRIGHTNESS 50%, COLOR 50%

3. Connect an oscilloscope to pin 1 (B OUT) of CN305, A board.

4. Set to Service Mode and select SAJ 3 ‘SCL’ with 1 and 4 of

the commander then adjust to VB2=VB3=VB4 with 3 and
6.

5. Press 

[MUTING]

 → - of the commander to write the data.

6. Adjust SAJ 3 ‘SCL’ as step 2 to 5 when receiving NTSC color-

bar.

VB1 VB2

VB3 VB4

VB2 = VB3 = VB4

6. Press 

[MUTING]

 → - of the commander to write the data.

VB1 VB2

VB3 VB4

VB1 = VB2 = VB3 = VB4

1. Input SECAM color-bar signal.

2. Connect the dual-trace oscilloscope to CN303 pin 9

(not mounted).

3. Adjust SERVICE MODE, ITEMS ‘SBF’ as shown below.

When replacing IC003 (MEMORY), be sure to change IC001 (µ-

COM) to the following new IC at the same time.

IC001(µ-CON): CXP86449-626S

1. Enter to Service Mode.

2. Press commander buttons 5 and - (Data Initialize), and 2

and - (Data Copy) to initialize the data.

3. Call each item number and check if the respective screen shows

the normal picture.

In cases where items are not well adjusted, rectify the items

with fine adjustment.

Write the data per each item number (

[MUTING]

 +-).

4. Select item numbers “OPB0” (OP1), “OPB1” (OP2) and

“OPB2”  (OP3) and respectively set the bit per model with

command buttons 3 and 6.

5. Press commander buttons 8 and - (Test Normal) to return

to the data that was set on the shipment from the factory.

(This will also cancel Service Mode.)

– 35 –

Item Number 00 – 0B

GEO 0

HPS (H POSITION)

GEO 1

HSZ (H SIZE)

GEO 2

PAP (PIN AMP)

GEO 5

VSZ (V SIZE)        

GEO 7

VLN (V LINEARITY)  

GEO 4

VPS (V POSITION)

GEO 6

SCO (VERTICAL S-Correction)

GEO 8

BOW (AFC.BOW)

GEO 9

AGL (AFC.ANGLE)

GEO 3

TLT (TRAPEZIUM)

GEO 0A UCP (UPPER CORNER PIN)

GEO 0B LCP (LOWER CORNER PIN)

H-TRAPEZOID (Rotate RV1801)

– 

40

 –

– 

41

 –

– 

39

 –

MAIN. TUVIF
<slave: 90H>

TU101
BTF-LG433
<slave:C0H>

COMB FILTER
(Glass Combs)

YC JUNGLE

IC301
CXA2139S

<slave:88H>

MONITOR
OUT
from H2

TV V in

TV L in

TV R in

TV Y in

V I Y in

V 2 Y in

4

6

9

7

11

CN2302

COMB Y in

COMB O in

V1 Y in

V1 L in

V1 R in

    V3 Y in

V3 L in

 

V2 Y in

V2 L in

V2 R in

V3 R in

V out

L out

R out

JACK BLOCK

J8402
PIN 9P

VIDEO IN 1

VIDEO IN 2

VIDEO IN 3
(FRONT)

AUDIO
PROSESSOR

IC8203
  TDA7429S

  <slave: 90H>

AUDIO OUT

IC201
TA8223K

RED OUT

GREEN OUT

BLUE OUT

VIDEO AUP
O701-712

IC1800
LA6510

H2

3P ASSY

R out

CRT SOCKET

G out

CRT
M68LNH070X

NECK ASSY

DY
Y29RSA-5

B out

R out

V out

U out

Y out

V in

U in

Y in

VM out

G out

B out

22

23

24

21

19

18

11

13

14

IK in

H. DRIVE

H. PULSE

E/W

VD+

VD- 

VM DRIVE
Q5902/5906

H-OUT
Q511
2SD2578

V-OUT
IC503
TDA8172

HDT
T501

H-DRIVE
Q506
2SC2785

PIN-CONT
IC502
NJM2903M

PIN-OUT
Q505
IRF614

PMT
T505

HLT
T504

FBT
T503
NX-4009

V. PARA
IC2801

DQP V. DRIVE
Q2802/2803/2804

DQP H. DRIVE
Q2801

DF TRANS
T2800

+B

Audio Front Vcc

+9V

11V

7V

+5V

5V REG & RESET

IC002 MM1319AFBE

9V REC IC603

5V REC IC604

STB TRANS

T604

STB SW TR

Q605 
2SK2845

SRT

T603

POWER

IC601
STR-F6656

LINE FILTER

T601

THP

THP600

DGC

Additional
Color Matrix

SYSTEM

Ucom

IC001
CXP86449

RECEIVER

*

SBX1981-51

  IC2901

H2

B2 

(COMB FILTER)

SIRCS

R G B

BLK

I2L

MEMORY

IC003
M24C08

32 31 30

37 39 40

15

28 29 30 31

Mon out

V out

R out

L out

*

AUDIO MIXER

  IC8602 UPC4558G2

Q310
CASIO
MIXER

Q310
CASIO
MIXER

SYSTEM DECODER with Ucom

IC801
SAA5261

<slave:88H>

 

* V1

(TELE TEXT)

PNC 
& ADC

(SYSTEM CONTROLLER, Y/C JUNGLE, DEFLECTION TUVIF, 
 FRONT AMP, POWER SUPPLY)

A

D3

(DQP & 
DYNAMIC FOCUS)

VM1

(VELOCITY 

MODULATION)

C6

(RGB OUT & PICTURE ROTATION)

(CONTROL 

PANEL)

(CISPR, A/C 
FUSE, A/V 
INPUT, 
MONITOR 
INPUT)

B6

LINE 
FILTER

T8601
T8602

AC CORD

(CISPR, A/C FUSE, 
A/V INPUT, 
MONITOR INPUT)

B6

* Not used for this model

J2903   3P