DOWNLOAD Sony KV-XF25M30 Service Manual ↓ Size: 1.76 MB | Pages: 71 in PDF or view online for FREE

– 29 –

For replacement of the Control Button and Light Guide, cut the welded portions from
them, exchange with the new parts, and fix them with screws (+BVTP) respectively.

Control button

Two screws
(+BVTP 3 

× 

12)

One screw
(+BVTP 3 

× 

12)

2

 Two screws

     (+BVTP 3 

× 

12)

PWB holder

– 30 –

1

 Two  claws  

2

 V1 board

3

 Two connectors

1

 Two connectors

4

 Four claws

5

 H3 Board

2

 Four connectors

3

 B3 Board  

5

 A Board

3

 Four connectors

1

 Two screws

     (+BVTAP 3 

× 

12)

2

 Three screws

     (+BVTAP 3 

× 

12)

1

 Two screws

     (+BVTP 3 

×

 12)

2

 Two claws

3

 Terminal bracket

– 31 –

NOTE:

The picture tube for Australian and Indonesian models are upside-
down, and the position for the anode-cap and tension spring is
changed accordingly.

•

NOTE : After removing the anode, short circuit the anode of the picture tube and

the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.

•

1

2

3

•

3

c

.

2

b

.

1

a

.

a

a

b

b

c

Anode button

!£

Four DGC clip

!¢

DGC
band

!∞

Demagnetic coil

!™

Four claws

1

Two screws 
(washer head)
(+P 4 

× 

16)

2

Speaker
(5cm)

!¶

Two screws
(Tapping)

3

Speaker
(15 

× 

6.5cm)

5

Speaker
(5cm)

6

Speaker
(15 

× 

6.5cm)

!§

Tension
spring

8

Chassis assy

!¡

Deflection
yoke

!º

Neck assy

9

C board

7

Anode cap

!•

Picture tube

Cushion

!¶

Two screws
(Tapping)

!ª

Two screws 
(+P 3 

× 

12)

4

@º

Two screws 
(washer head)
(+P 4 

× 

16)

Two screws 
(+P 3 

× 

12)

– 32 –

•

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

•

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise noted:

PICTURE control ...........................................................  normal

BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Color-bar/Pattern Generator

2. Degausser

3. Oscilloscope

................................................................................................................................................................................................................................

Neck assy

G2

G1

G3

Behind the G2 edge

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

Red

Blue

Green

}

normal

•

In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

•

Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast

Brightness

2. Position neck assy as shown in Fig3-2.

3. Set the pattern generator raster signal to a green raster.

4. Move the deflection yoke to the rear and adjust with the  purity

control so that the green is at the center and the blue and the red

take up equally sized areas on each side.

(See Figures 3-1 through 3-4.)

5. Move the deflection yoke forward and adjust so that the entire

screen is green. (See Figure 3-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.

(See Figure 3-5.)

Purity control