DOWNLOAD Sony KV-XF21M80 Service Manual ↓ Size: 1.26 MB | Pages: 46 in PDF or view online for FREE

Model
KV-XF21M80
Pages
46
Size
1.26 MB
Type
PDF
Document
Service Manual
Brand
Device
TV
File
kv-xf21m80.pdf
Date

Sony KV-XF21M80 Service Manual ▷ View online

– 6 –
KV-XF21M80
RM-952
4.
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] /
channel 
[5] /
Sound volume
[-] /
Power ON
˘
Note that this differs from entering the service mode (mode volume 
[+]
).
Self-Diagnosis screen display
002 : 000
003 : 000
004 : 000
005 : 001
Numeral "0" means that no fault has been detected.
Numeral "I" means a fault has been detected.
101 : 000
SELF DIAGNOSTIC
5.
HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel 
[8] /
0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
– 7 –
KV-XF21M80
RM-952
6.
SELF-DIAGNOSTIC CIRCUIT
[+B overcurrent ªOCPº]
Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Horizontal deflection overdrive]
Occurs when an overdrive on H drive line is detected by D526. Power supply will be shut
down when detect it.
[Vertical deflection stopped]
Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Vertical deflection overcurrent]
Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[White balance failure]
If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
IC301
Y/CHROMA JUNGLE
FROM
CRT
FROM
[+B]
 Q604 C
[H]
 D526
[V]
 Q509/507
IC001
SYSTEM
IC003
MEMORY
B-DAT
IO-SDAT
IK-IN
MP/
PROTECT
IO-8DAT
O-LED
SDA
5
45
21
18
51
46
35
– 8 –
KV
-XF21M80
RM-952
SECTION  1
GENERAL
The operating instructions mentioned here are partial abstracts 
from the Operating Instruction Manual.  The page numbers of 
the Operating Instruction Manual remain as in the manual.
2
WARNING
•  Dangerously high voltages are present inside the TV.
•  Operate the TV only between 110 – 240 V AC.
To prevent fire or shock hazard, do not expose
the TV to rain or moisture.
Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.
Do not open the cabinet and the rear cover of the
TV. Refer servicing to qualified personnel.
Do not install the TV in hot, humid or excessively
dusty places.
Do not install the TV in a confined space, such
as a bookcase or built-in cabinet.
Do not block the ventilation openings of the TV.
Do not pull the power cord to disconnect the TV.
Pull it out by the plug.
Disconnect the power cord during lightning
storms or if you are not going to use the TV for
several days.
Install the TV in a stable position. Do not allow
children to climb onto it.
Do not plug in too many appliances to the same
power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.
4
Using Your New TV
Getting Started
 Step 1
Connect the antenna
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
Connecting an indoor antenna
Using Your New TV
IEC connector
(not supplied)
: Signal flow
Antenna cable (not supplied)
Antenna cable (not supplied)
Rear of TV
or
Note
• You are advise to use an outdoor antenna for better reception.
WOOFER (8
)
L(MONO)
L(MONO)
1
Rod antenna and cable
(supplied)
Rear of TV
1
2
3
– 9 –
KV
-XF21M80
RM-952
5
Using Your New TV
Using Y
our New TV
VIDEO
VIDEO IN
VIDEO OUT
AUDIO
L(MONO)
1
To video and
audio outputs
VCR
 (yellow)
-L (MONO) (white)
-R (red)
Antenna cable (not supplied)
To  1
(video input)
Audio/Video cable
(not supplied)
: Signal flow
To antenna
output
To ˘
(antenna)
Notes
• If you connect a monaural VCR, connect the yellow plug to 
 (the
yellow jack) and the black plug to  -L (MONO) (the white jack).
• If you connect  a VCR  to the ˘ (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV.
• When no signal is input to the connected video equipment, the TV screen
becomes blue.
CAUTION
Do not connect the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
Rear of TV
continued
Connecting a VCR
To watch the video, press … 
 (see page 13).
6
Using Your New TV
1
2
Front of TV
1
1
VHF LOW  B/G
ONE-PUSH  AUTOMATIC  PROGRAMMING
ONE-PUSH  AUTOMATIC  PROGRAMING
Step 2
Insert the batteries
into the remote
Note
• Do not use old batteries nor use different types of batteries together.
Step 3
Preset the channels automatically
Tip
• If you want to stop the automatic channel presetting, press AUTO PROGR again.
Note
• If your TV has preset an unwanted channel or cannot preset a particular channel,
then preset your TV manually (see page 9).
Now You Are Ready. . .
To watch your TV, see page 12.
Getting Started (continued)
Page of 46
Display

Click on the first or last page to see other KV-XF21M80 service manuals if exist.