Sony KV-XF21M80 (serv.man3) Service Manual ▷ View online
– 6 –
KV-XF21M80/XF21M8J
RM-952
4.
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] /
channel
[5] /
Sound volume
[-] /
Power ON
˘
Note that this differs from entering the service mode (mode volume
[+]
).
Self-Diagnosis screen display
002 : 000
003 : 000
004 : 000
005 : 001
003 : 000
004 : 000
005 : 001
Numeral "0" means that no fault has been detected.
Numeral "I" means a fault has been detected.
101 : 000
SELF DIAGNOSTIC
5.
HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel
[8] /
0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
– 7 –
KV-XF21M80/XF21M8J
RM-952
6.
SELF-DIAGNOSTIC CIRCUIT
[+B overcurrent ªOCPº]
Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Vertical deflection stopped]
Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
shut down the power supply.
[Vertical deflection overcurrent]
Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
shut down when detect this by IC001.
[White balance failure]
If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
IC301
Y/CHROMA JUNGLE
FROM
CRT
FROM
[+B]
Q604 C
[V]
Q509/507
IC001
SYSTEM
IC003
MEMORY
B-DAT
IO-SDAT
IK-IN
MP/
PROTECT
PROTECT
IO-8DAT
O-LED
SDA
5
45
21
18
51
46
35
– 8 –
KV
-XF21M80/XF21M8J
-XF21M80/XF21M8J
RM-952
SECTION 1
GENERAL
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
2
WARNING
• Dangerously high voltages are present inside the TV.
• Operate the TV only between 110 – 240 V AC.
To prevent fire or shock hazard, do not expose
the TV to rain or moisture.
the TV to rain or moisture.
Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.
falls into it. Have it checked immediately by
qualified personnel only.
Do not open the cabinet and the rear cover of the
TV. Refer servicing to qualified personnel.
TV. Refer servicing to qualified personnel.
Do not install the TV in hot, humid or excessively
dusty places.
dusty places.
Do not install the TV in a confined space, such
as a bookcase or built-in cabinet.
Do not block the ventilation openings of the TV.
as a bookcase or built-in cabinet.
Do not block the ventilation openings of the TV.
Do not pull the power cord to disconnect the TV.
Pull it out by the plug.
Pull it out by the plug.
Disconnect the power cord during lightning
storms or if you are not going to use the TV for
several days.
storms or if you are not going to use the TV for
several days.
Install the TV in a stable position. Do not allow
children to climb onto it.
children to climb onto it.
Do not plug in too many appliances to the same
power socket. Do not damage the power cord.
power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.
4
Using Your New TV
Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
Using Your New TV
IEC connector
(not supplied)
(not supplied)
To video and
audio outputs
audio outputs
VCR
(yellow)
-L (MONO) (white)
-R (red)
-R (red)
Antenna cable (not supplied)
To … 1
(video input)
(video input)
Audio/Video cable
(not supplied)
(not supplied)
: Signal flow
To antenna
output
output
Antenna cable
(not supplied)
(not supplied)
Rear of TV
Rear of TV
Connecting a VCR
To watch the video, press …
(see page 12).
Note
• You are advised to use an outdoor antenna for better reception.
• You are advised to use an outdoor antenna for better reception.
Rod antenna and cable
(supplied)
(supplied)
or
VIDEO
VIDEO IN
VIDEO OUT
AUDIO
L(MONO)
1
or
To ˘
(antenna)
(antenna)
: Signal flow
– 9 –
KV
-XF21M80/XF21M8J
-XF21M80/XF21M8J
RM-952
5
Using Your New TV
Using Y
our New TV
Notes
• If you connect a monaural VCR, connect the yellow plug to
• If you connect a monaural VCR, connect the yellow plug to
(the
yellow jack) and the black plug to -L (MONO) (the white jack).
• If you connect a VCR to the ˘ (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV.
• When no signal is input to the connected video equipment, the TV screen
becomes blue.
Step 2
Note
• Do not use old batteries nor use different types of batteries together.
• Do not use old batteries nor use different types of batteries together.
Step 3
CAUTION
Do not connect the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
Insert the batteries
into the remote
into the remote
Preset the channels automatically
Tips
• If you want to stop automatic channel presetting, press SELECT twice.
• If your TV has preset an unwanted channel or cannot preset a particular
• If you want to stop automatic channel presetting, press SELECT twice.
• If your TV has preset an unwanted channel or cannot preset a particular
channel, then preset your TV manually (see page 9).
Note
• During automatic channel presetting, your TV screen will indicate “B/G”,
• During automatic channel presetting, your TV screen will indicate “B/G”,
“I”, “D/K” or “M” for the TV system.
Now You Are Ready. . .
To watch your TV, see page 11.
Front of TV
ONE-PUSH AUTOMATIC PROGRAMING
1
1
ONE-PUSH AUTOMATIC PROGRAMMING
1
2
VHF LOW B/G
6
Using Your New TV
Connecting optional components
You can connect optional audio/video components, such as a VCR, multi disc player,
camcorder, video game or stereo system.
camcorder, video game or stereo system.
To watch the picture of the connected equipment, press …
(see page 12).
Connecting a camcorder/video game equipment
using the … (video input) jacks
using the … (video input) jacks
Note
• You can also connect video equipment to the … 1 (video input) jacks at
• You can also connect video equipment to the … 1 (video input) jacks at
the rear of your TV.
Connecting audio/video equipment using the Ú
(monitor output) jacks
(monitor output) jacks
Note
• When connecting a monaural VCR, connect the yellow plug to
• When connecting a monaural VCR, connect the yellow plug to
(the
yellow jack) and the black plug to -L (MONO) (the white jack).
L(MONO)
1
ONE-PUSH AUTOMATIC PROGRAMING
ONE-PUSH AUTOMATIC PROGRAMING
2
Front of TV
Camcorder
Video game
equipment
equipment
To video and
audio outputs
audio outputs
(yellow)
-L (MONO)
(white)
-R (red)
Rear of TV
To
antenna
output
antenna
output
To video and
audio inputs
audio inputs
or
Audio system
To
audio
inputs
audio
inputs
VCR
:Signal flow
:Signal flow
To… 2
(video input)
(video input)
To Ú
(monitor
output)
(monitor
output)
or
Audio/Video cable (not supplied)
Antenna cable (not supplied)
Audio/Video cable
(not supplied)
(not supplied)
or
Click on the first or last page to see other KV-XF21M80 (serv.man3) service manuals if exist.