DOWNLOAD Sony KV-XA34M30A Service Manual ↓ Size: 4.68 MB | Pages: 70 in PDF or view online for FREE

–

 21 

–

2  One screw (+BVTP 4 

× 16)

6  One screw 
      (+BVTP 4 

× 16)

1  Two screws (+BVTP 3 

× 12)

5  Two screws 
      (+BVTP 3 

× 12)

3 Bracket HVC

4 HV Cap block

7 Terminal bracket

8 J Board

1 Three connectors

2 One claw

3 D2 board

3 Two connectors

3 Two connectors

1 Two connectors

5 H board

4 Four claws

2  One screw washer head
      (+BVTP 3 

× 12)

3 B9 Board  

4 A Board

1 Three screws washer head
     (+BVTAP 3 

× 12)

2 Two screws
     (+BVTAP 3 

× 12)

5  One screw
      (+BVTP 4 

× 16)

6 Two claws

5 Terminal bracket

 

5  Two screws

       (+BVTP 3 

× 12)

–

 22 

–

•REMOVAL OF ANODE-CAP

NOTE : After removing the anode, short circuit the anode of the picture tube and

the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.

•REMOVING PROCEDURES

1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.

3 Do not turn the foot of rubber over too hard.

• HOW TO HANDLE AN ANODE-CAP

3 When one side of the rubber cap is separated from the anode button,  the anode-cap

c.

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.

1 Turn up one side of the rubber cap in the direction indicated by the arrow a.

Anode button

a

a

b

b

c

@¡ Demagnetic coil

!ª

Holder DGC

 

!¶ Two DGC clips

 

!§ Two DGC clips

 

@º CushionDGC

 

@™ Chassis assy

 

!• DGC

      band

9 Two screws 
     (washer head)
     (+P 4 

× 16)

Cap, screw

7 Two screws 
     (+BVTP 4 

× 16)

8 Speaker
     (13 

× 7 cm)

6 Tweeter Sheet

1 Cushion

CRT (Top,right)
Support Assy

Two screws 
(+BVTP 4 

× 16)

Two screws 
(+BVTP 4 

× 16)

@£ Picture tube

CRT (Top,left)
Support Assy 

!™ Anode cap

 

!¡ Two Nuts, 

Special CRT

Cap, screw

!£ Deflection
     yoke

!¢ Neck assy

!∞ C6 Board

5 Two screws 
     (washer head)
     (+P 4 

× 16)

 

7 Two screws 

      (+BVTP 4 

× 16)

4 Speaker
     (13 

× 7 cm)

2 Tweeter Sheet

!™ Tension
      spring

 

!º Two Nuts, 

Special CRT

Note:
•

The picture tube for South Africa model is upside down, and the position for
the anode cap and tension spring are changed accordingly.

•

Please remove necessary CRT support located on top left, top right, prior to
removing the CRT.

– 23 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items
will be reset to its original setting (shipment condition)

The way to access to the "RESET" Function:-

a) By pressing "MENU" button or "SELECT" button (for non-menu models) on the Front Key Input

and hold it down for 5 seconds.

Sequential to the resetting operation (either methods being used in No. 2), TV set would shut down once
and automatically turn on again. The power-off duration is expected to be about 500msec. An OSD
message, "RESET" tentatively will be displayed for 10 sec after IK status gets stable.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other
remains at the last selection by user.

Items that remains at the last selection by user

Reset Items

Program No., Favourite CH Setup, PIC rotation,

OSD Language, Fine tuning, TV System, Skip

*  = only when in RF mode
*1= Not used for these models

Video input

RF

Volume

30

Picture mode

DYNAMIC

Sound mode

DYNAMIC

Surround mode

OFF

Color system(video)

AUTO

Multi picture(PIP) *1

OFF

PIP position *1

Bottom-right

Favourite CH mode

AUTO

OSD recall

OFF

Intelligent volume

OFF

ECO mode *

OFF

Color system(RF)

AUTO*

Antenna sensitivity

HIGH*

Stereo mode *

STEREO/NICAM*

Bilingual mode *

MAIN*

High-deviation mode

AUTO*

Child lock

OFF*

Wide mode

OFF

Game mode

OFF

Teletext mode *1

OFF

Sleep timer

OFF

Wake-up timer

OFF

Sound muting

OFF

– 24 –

• The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

• These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise

noted:

PICTURE control ............................................................ normal

BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Color-bar/Pattern Generator

2. Degausser

3. Oscilloscope

................................................................................................................................................................................................................................

}

normal

Preparation :
• In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

• Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast

Brightness

2. Position neck assy as shown in Fig4-2.

3. Set the pattern generator raster signal to a green raster.

4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue

and the red take up equally sized areas on each side.

(See Figures 4-1 through 4-4.)

5. Move the deflection yoke forward and adjust so that the en-

tire screen is green. (See Figure 4-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.

(See Figure 4-5.)

G2

G1

G3

Neck assy

Behind the G3 edge

Purity control

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a