DOWNLOAD Sony KV-SZ29M50 (serv.man2) Service Manual ↓ Size: 4.42 MB | Pages: 62 in PDF or view online for FREE

– 5 –

1 Twelve screws
     (+BVTP 4 

× 16

       Type2 IT-3)

2 Rear cover

1 Two screws

          Tapping screw 

       (+PWH 4x16)

2 H1 Board    

1 Two Hooks     

1 A Board

– 6 –

•

Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.

1) Remove the rear cover.
2) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.

Remove Chassis Assy.

3) Place the TV set with the CRT face down on a cushion jig.

qd

 Loosen the Deflection Yoke

fixing screw and remove

qa

 Earth Coating Assy

4

 Anode Cap Removal

7 Band, DGC Removal (x1)

5 CV Board Removal

6 Loosen the Neck Assembly

fixing screw and remove VM coil

9

 Holder, DGC Removal (x2)

8

 Spring Tension Removal (x2)

qf

 Screw Tapping

     7+ Crown Washer

0

 Degaussing Coil

qs

 Supports, CRT(2) Removal

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or

carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direction

indicated by the arrow b.

3 When one side of the rubber cap is separated from the

anode button,  the anode-cap can be removed by turning
up the rubber cap and pulling it up in the direction of the
arrow c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with sharp

2 Do not press the rubber too hard so as not to damage

3 Do not turn the foot of rubber over too hard.

a

a

b

b

c

 Anode Button

– 7 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position VM coil as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

Purity control

VM coil

G2

G1

G3

Align the edge of
the VM coil with
the edge of the G3 grid.

G4

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.

– 8 –

Moved RV750 (H.STAT)

R

R

G

G

B

B

A

A

B

B

B

B

R

G

G

R

B

Preparation:
• Before starting, perform FOCUS adjustment.
• Picture Mode "SOFT"
• Receive dot/cross hatch pattern.

1. (Moving vertically), adjust the 4 pole magnet to

converge red, green and blue dots in the center of
the screen.

2. Tilt the 4 pole magnet and adjust static convergence

to open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves
as shown below:-

b) Horizontal Static Convergence
If the blue dots does not converge with the red and
green dots, use the 6 pole magnet to adjust in
the manner described below:-

1. Receive cross hatch signal.
2. Set Picture to "MINIMUM", Brightness to "STANDARD".
3. Adjust the Y separation axis correction magnet on

the Neck Assembly so that the horizontal lines at
the top and bottom of the screen are straight.

Red

Blue

Red

Blue

6 Pole Magnet

4 pole Magnet

DY pocket

Purity

6 Pole

Magnet

4 Pole

Magnet

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

4 pole magnet

RV750
H. STAT

RV1800
G2 (SCREEN) 

Center dot

R     G     B

G

R

B