DOWNLOAD Sony KV-SZ252M50 (serv.man3) Service Manual ↓ Size: 8.42 MB | Pages: 72 in PDF or view online for FREE

– 8 –

Dress Conn Assy, 4P VH into hook as shown.

Right side

Left side

Dress Conn Assy, 5P YUV around shield case.
Use pin, wires A019 and A017 to dress Conn Assy, 
5P YUV as shown.

 

 

CN007

CN9201

Make sure the UL tape is positioned at

the sharp edge of shield case to prevent

wire from being scratched

Dress Conn Assy, 5P YUV

around shield case

Keep wires away

from R121

CN905

Pin, wire A019

Pin, wire A017

Conn Assy, 5P YUV

i) Earth Assy, Coating is installed as shown.

Dress Conn Assy, 4P VM behind Conn Assy, 5P Front In 
as shown.
Conn Assy, 5P Front In is used to prevent Conn Assy, 
4P VM from bending towards T504, R579 and R5032 
(high temperature parts).

CAUTION:
Keep Conn Assy, 5P Front In away from deflection area
(T504, R5032, etc.) when dressing.

Dress Conn Assy, 4P VM behind

Conn Assy, 5P Front In

Lead Assy, Earth is

above Conn Assy, 5P

Conn Assy, 5P

Front  In

Deflection area

T504

R5032

CN003

CN9201

R579

Conn Assy, 4P VM

Insert Connector Assy,

4P VH into holder

CN6101

CN4102

– 9 –

ii) Insert the 2 Earth Assy, Coating wires to CN706 &  
CN707 as shown. Insert Conn Assy, 7P RGB into CN701.

CV board

Heatsink A751

Conn Assy, 7P RGB

CN707

Earth Assy, Coating dressing

CV board

CN707

CN706

CN706

Earth Assy,

Coating wires

CN701

BLK+BLK

to CN706

BLK+BLK

to CN707

Make a 'S' shaped loop on Conn Assy, 5P Front In  
as shown. Keep wires away from heatsink A010.

Next, Conn Assy, 5P Front In is dressed together with  
Lead Assy,Earth using purse lock Ø 5. Refer to next page.

Lead Assy, Earth

Lead Assy, Speaker

Heatsink A010

Conn Assy, 5P

Front In

Insert Lead Assy, H Static into CRT socket and RV750 as 
shown. Make sure the wire is naturally curved, to avoid 
touching CRT neck.

Lead Assy, H static

CRT socket

CRT neck

RV750

– 10 –

Note: Dress while chassis is halfway docked into beznet.

CAUTION:
Prevent tie, cable from touching rear cover or any 
enclosures by turning them away from it --> avoid 
rattle sound. Also prevent tie, cable's end from  
touching solder side of board.

CAUTION:
Prevent tie, cable from touching rear cover or any 
enclosures by turning them away from it --> avoid 
rattle sound. Also prevent tie, cable's end from  
touching solder side of board.

i) Dress Conn Assy, 6P and Conn Assy, 4P VM using tie,
cable at alignment hole 'B' on CV board as shown.
ii) Dress Conn Assy, 4P 200V; Conn Assy, 6P; Conn Assy,
4P VM; Lead Assy, G2 and Lead Assy, Focus with purse
lock Ø 5.

  

Lead Assy, Earth

Conn Assy, 5P Front In

Heatsink A010

Tie, cable at alignment hole 'B'

Conn Assy, 6P

Conn Assy, 4P VM

Conn Assy, 4P VM

Conn Assy, 4P 200V

Conn Assy, 6P

Lead Assy, Focus

Lead Assy, G2

Conn Assy, 4P 200V

Lead Assy, G2

Lead Assy, Focus

Pin, wire A707

Purse lock Ø 5

Purse lock Ø 5

Purse lock Ø 5

Lead Assy, Speaker is not dressed 

together with purse lock. Keep Lead Assy,  

Speaker away from heatsink A010 by

dressing it close to the CRT

Make a 'S' shaped loop on 

Conn Assy, 5P Front In 

and dress together with  

Lead Assy, Earth using 

purse lock Ø 5

Conn Assy,  
5P Front In

Lead Assy, Earth

i) Dress Conn Assy, 7P RGB; Conn Assy, 5P Front In and
Lead Assy, Earth using purse lock Ø 9. Keep wires away from 
heatsinks and high-temperature parts. 

Lead Assy, Earth is behind

Conn Assy, 7P RGB

Purse lock Ø 9

Conn Assy, 7P RGB

Conn Assy, 5P Front In

CN004

Make loop of Conn Assy, 7P RGB as large as 

possible when dressing with purse lock

Lead Assy, Earth

Purse lock Ø 9

Conn Assy, 7P RGB

Lead Assy, Earth

Conn Assy, 5P Front In

Keep Conn Assy, 5P Front In wire in an upward
path from CN9201 to where it is dressed with 
purse lock Ø 9. This is to keep it away from 
deflection area.

– 11 –

Avoid any stress on Lead Assy, G2; Lead Assy, Focus and
terminal at W7001.

CN1802

Rotation Coil Conn

Dress Rotation Coil

connector together with Lead

Assy, G2; Lead Assy Focus

and Conn Assy, 4P 200V

using pin, wire A707

A715

A713

Conn Assy, 4P 200V

W7001

Lead Assy, G2

Lead Assy,

Focus

Keep wire away

from R781

Keep wire away

from R781 and 

heatsinks A713, A715.

Install Rotation Coil as shown.
1) Coil positioned in clockwise direction.
2) Wire is at 3 o'clock position.

Dress DY Connector; Conn Assy, 4P 200V;
Conn Assy 4P VM and Conn Assy, 6P using purse lock
Ø 9 as shown.

CAUTION:
Prevent wires from touching rear cover or any 
enclosures by turning them away from it--> avoid rattle
sound.

Rotation Coil

DY

Wire from Roation Coil

Earth Assy,

Coating wires

Rotation coil conn is dressed outside

and below Earth Assy, Coating wires.

Note: Make sure DY connector is inserted securely.
 

--> prevent it from coming out.

DY Connector

Conn Assy,

4P 200V

Conn Assy, 6P

  

Conn Assy,  

4P VM

Purse lock Ø 9

DY Conn

Conn Assy,

4P 200V

Conn Assy, 4P

Conn Assy, 6P

Purse lock Ø 9