Sony KV-SW29M50 Service Manual ▷ View online
– 35 –
KV-SW29M61/M81/M50/M80/SW29N60
RM-W103
RW-W104
RM-W150
WIDE MODE (60Hz)
(V-Compression Adjustment)
1. Input Monoscope signal.
2. Adjust condition to WIDE MODE : ON.
3. Copy (item from NORMAL MODE 60Hz) adjusted
1. Input Monoscope signal.
2. Adjust condition to WIDE MODE : ON.
3. Copy (item from NORMAL MODE 60Hz) adjusted
data for the following items:
Service Item
Service Item
GEOM: 003
VLIN
VERTICAL LINEARITY
010
VSLP
VERTICAL SLOPE (VS)
011
VSIZ
VERTICAL AMPLITUDE
012
SCOR
S-CORRECTION (SC)
4. Raise/lower data using
3
and
6
buttons, select and
adjust the following item to obtain optimum image.
Service Item
Service Item
GEOM: 000
HPOS
HORIZONTAL SHIFT (HS)
001
HPAR
HORIZONTAL
PARALLELOGRAM
PARALLELOGRAM
002
HBOW
HORIZONTAL BOW
005
HSIZ
EW WIDTH (EW)
006
EWPW
EW PARABOLA/
WIDTH (PW)
WIDTH (PW)
007
UCOP
EW UPPER CORNER
PARABOLA
PARABOLA
008
LCOP
EW LOWER CORNER
PARABOLA
PARABOLA
009
EWTZ
EW TRAPAZIUM
013
VPOS
VERTICAL SHIFT (VSH)
3-5. PICTURE DISTORTION ADJUSTMENT
H. CENTER ADJUSTMENT (HPOS)
1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select the HPOS item with
2. Activate the Service Mode.
3. Select the HPOS item with
1
and
4
.
4. Adjust the value of HPOS with
3
and
6
for the best
horizontal center.
5. Press [MUTING] then
-
to save into the memory.
H. SIZE ADJUSTMENT (HSIZ)
1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select HSIZ with
2. Activate the Service Mode.
3. Select HSIZ with
1
and
4
.
4. Adjust with
3
and
6
for the best horizontal size.
5. Press [MUTING] then
-
to save into the memory.
(
)
(
)
– 36 –
KV-SW29M61/M81/M50/M80/SW29N60
RM-W103
RW-W104
RM-W150
V. SIZE ADJUSTMENT (VSIZ)
1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select theVSIZ item with
2. Activate the Service Mode.
3. Select theVSIZ item with
1
and
4
.
4. Adjust value of VSIZ with
3
and
6
for the best
vertical size.
5. Press [MUTING] then
-
to save into the memory.
V. CENTER ADJUSTMENT (VPOS)
1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select VPOS item with
2. Activate the Service Mode.
3. Select VPOS item with
1
and
4
.
4. Adjust value of VPOS with
3
and
6
for the best
vertical size.
5. Press [MUTING] then
-
to save into the memory.
V. LINEARITY (VLIN), S CORRECTION (SCOR), EW
PARABOLA/WIDTH (EWPW), AND EW TRAPEZIUM
(EWTZ) ADJUSTMENTS
PARABOLA/WIDTH (EWPW), AND EW TRAPEZIUM
(EWTZ) ADJUSTMENTS
1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select VLIN, SCOR, EWPW, and EWTZ with
2. Activate the Service Mode.
3. Select VLIN, SCOR, EWPW, and EWTZ with
1
and
4
.
4. Adjust with
3
and
6
for the best picture.
5. Press [MUTING] then
-
to save into the memory.
EW TRAPEZIUM (EWTZ)
EW PARABOLA/WIDTH (EWPW)
S CORRECTION (SCOR)
VERTICAL LINEARITY (VLIN)
HORIZONTOL PARALLELOGRAM (HPAR), H BOW
(HBOW), UPPER PIN (UCOP) AND LOW PIN (LCOP)
ADJUSTMENTS
(HBOW), UPPER PIN (UCOP) AND LOW PIN (LCOP)
ADJUSTMENTS
1. Input Monoscope signal.
2. Activate the Service Mode.
3. Select the HPAR, HBOW, UCOP, and LCOP with
2. Activate the Service Mode.
3. Select the HPAR, HBOW, UCOP, and LCOP with
1
and
4
.
4. Adjust with
3
and
6
for the best picture.
5. Press [MUTING] then
-
to save into the memory.
EW UPPER CORNER PARABOLA (UCOP)
EW LOWER CORNER PARABOLA (LCOP)
HORIZONTOLPARALLELOGRAM (HPAR)
HORIZONTOL BOW (HBOW)
–
37
–
KV
-SW29M61/M81/M50/M80/SW29N60
-SW29M61/M81/M50/M80/SW29N60
RM-W103
R
W
-W104
RM-W150
SECTION 4
DIA
GRAMS
4-1.
BLOCK DIA
GRAM
VIF
SAW
SIF
SAW
MAIN
Power
Supply
Stdby
Power
FSS TUNER
Y
U
V
L
R
24.576MHz
DVD in
Rear AV in
Front AV in
Mon out
Mon
out
AV1
AV2
in
AV3
in
DVD
in
AC in ~
110 ~ 220V
CISPR/
PFC
Relay
LOW B
Stdy 3.3
AUDIO VCC
L
Audio Amp
ATT
NVM
V Def
H Def
DF
DQP
H Def
DF
DQP
VM
RGB Amp
Rot Amp
LCC Amp
6W
R
6W
L,R
H
P
P
EW, Hd
L,R
V+, V-
PWM
RGB
SIRCS
KEY
buttons
PLL
I/O Port
I/O Port
VIF & SIF
POWER
Color
Decoder
YUV
Processor
Jungle
RGB
A
D
C
C
D
A
C
Stereo,
DSP
Micro
Text
CC & V-chip
LED
+B
– 38 –
KV-SW29M61/M81/M50/M80/SW29N60
RM-W103
RW-W104
RM-W150
4-2. CIRCUIT BOARDS LOCATION
4-3. SCHEMATIC DIAGRAM INFORMATION
Note:
•
•
All capacitors are in µF unless otherwise noted.
•
All electrolytic capacitors are rated at 50V unless otherwise
noted.
noted.
•
All resistors are in ohms.
k
k
Ω = 1000Ω, MΩ = 1000kΩ
•
Indication of resistance which does not have rating electrical
power is as follows.
power is as follows.
Pitch: 5 mm
Rating electrical power 1/4W (CHIP: 1/10W)
Rating electrical power 1/4W (CHIP: 1/10W)
•
: nonflammable resistor.
•
: fusible resistor.
•
¢
: internal component.
•
: panel designation or adjustment for repair.
•
All variable and adjustable resistors have characteristic curve
B unless otherwise noted.
B unless otherwise noted.
•
Readings are taken with a color-bar signal input.
no mark
no mark
: Common
(
)
: PAL
[
]
: NTSC 3.58
•
Readings are taken with a 10M
Ω digital multimeter.
•
Voltage are dc with respect to ground unless otherwise
noted.
noted.
•
Voltage variations may be noted due to normal production
tolerances.
tolerances.
•
All voltage are in Volt.
•
✽
: Cannot be measured.
•
Circled numbers are waveform references.
•
: B +bus.
•
: B –bus.
•
k
: signal path.
Note: The reference number which starts with Wxxx
(eg: W003) indicates a wire to wire connection.
Note: Components marked as XX are not fitted on this
model.
Reference information
RESISTOR
RESISTOR
: RN
METAL FILM
: RC
SOLID
: FPRD
NONFLAMMABLE CARBON
: FUSE
NONFLAMMABLE FUSIBLE
: RS
NONFLAMMABLE METAL OXIDE
: RB
NONFLAMMABLE CEMENT
: RW
NONFLAMMABLE WIREWOUND
:
✽
ADJUSTMENT RESISTOR
COIL
: LF-8L
MICRO INDUCTOR
CAPACITOR
: TA
TANTALUM
: PS
STYROL
: PP
POLYPROPYLENE
: PT
MYLAR
: MPS
METALIZED POLYESTER
: MPP
METALIZED POLYPROPYLENE
: ALB
BIPOLAR
: ALT
HIGH TEMPERATURE
: ALR
HIGH RIPPLE
Note:
The component identified by shading and
mark
mark
! are critical for safety. Replace only
with part number specified.
Note: "A" board schematic diagram is divided into 3
blocks. Each block is named by its function and
block "number". eg: Processor/Audio/Tuner/Jack
(Block 001).
Joint connection between boards can be identified
using the block number followed by the grid's guide.
block "number". eg: Processor/Audio/Tuner/Jack
(Block 001).
Joint connection between boards can be identified
using the block number followed by the grid's guide.
eg:-
<
+B
002:16F
Meaning: Block 001 joint "+B" is connected to Block
002 joint "+B" located at grid 16F.
002 joint "+B" located at grid 16F.
A Board
C Board
J3 Board
D3 Board
H4 Board
F Board
H5 Board
VM Board
Click on the first or last page to see other KV-SW29M50 service manuals if exist.