DOWNLOAD Sony KV-SW252M50 Service Manual ↓ Size: 5.37 MB | Pages: 69 in PDF or view online for FREE

– 4 –

[+B overcurrent $OCP%]

Occurs when an overcurrent on the +B(135V) line is detected by pin 97 of IC001 (A board).
If the voltage of pin 97 of IC001 (A board) is more than 4V, the unit will automatically go to
standby.

[V-PROTECT]

Occurs when an absence of the vertical deflection pulse is detected by pin 116 of IC001
(A board).

[IK $AKB%]

If the RGB levels* do not balance within 15 sec after the power is turned on, this error will be
detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.

Occurs when IC001 internal HV protect detects an abnormal H-Pulse (frequency) due to
improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be
detected. eg: IC602, IC604 go faulty.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

A BOARD

IC001

Y/CHROMA JUNGLE

A BOARD

IC804

V.OUT

A BOARD

IC001

SYSTEM

A BOARD

IC003

MEMORY

FROM

C BOARD

IC751 PIN 5

IK

EHTO

RED LED

DISPLAY

SDA1

V.GUARD

SDA

5

F.B-PLS

3

116

45

97

7

A BOARD

FROM

Q816

COLLECTOR

30

POWER SUPPLY NG (+5V)
for VIDEO PROCESSOR

2 : 

000

3 :

N/A

4 :

000

5 :

001

8 :

002

101 :

N/A

"0" means no fault has been detected.

"1" means a fault has been detected.
"2" means two faults has been detected.

"N/A" means not available for this models.

SELF DIAGNOSTIC

5

8

1.

Display self diagnostic screen

[Display] t [Channel    ] t [Volume    ] t [Power / TV]

Note: The above must be performed while TV is on standby mode.

2.

Stop standby flash

i) Turn off power switch on main.
ii) Unplug power cord from the outlet.

3.

Clear fault result

In Self Diagnostic Screen, press, 

[Channel    ] t 

-

Note: Diagnostic results display on screen is not automatically cleared. Therefore,
clear result after completion of repair.

4.

Quit self diagnostic screen

Turn off power switch of remote commander or main unit.

– 5 –

2 Rear cover

1 Nine screws
     (+BVTP 4 × 16)

2 Two screws
     (Washer Head) 
     (+P4x16)

3 One screw
    (+BVTP 3 

× 12)

1 One screw
     (+BVTP 4 

× 16 Type2 IT-3)

4 One screw
    (+BVTP 3 

× 12)

2 Terminal bracket

2 hooks

3 F2 Board

1 J3 Board

2 Two screws
     (+BVTP 3 × 12 Type2 IT-3)

– 6 –

2 F1 Board

1 Two hooks

3 One screws
     (+BVTP 3 × 12 Type2 IT-3)

3 Four hooks

1 Five hooks

2 H7 Board

4 H4 Board

5 Five screws
    (3 

× 12)(+) BVTAP

3 Four hooks

2 A Board

– 7 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

•

1 Turn up one side of the rubber cap in the direction

indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direc-

tion indicated by the arrow b.

3 When one side of the rubber cap is separated from the

anode button,  the anode-cap can be removed by
turning up the rubber cap and pulling it up in the
direction of the arrow c.

•

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

•

Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.

1) Remove the rear cover.
2) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.

Remove Chassis Assy.

3) Place the TV set with the CRT face down on a cushion jig.

4

 Anode Cap Removal

6

 Degaussing Coil

0

 Loosen the Neck Assembly 

fixing screw and remove
Neck Assy & VM board

qa

 Loosen the Deflection Yoke

fixing screw and remove

9

 C Board Removal

7

 Spring Tension(2x) 

Removal

5

 Holder, DGC

Removal (2x)

8

 Earth Coating Assy

qs

 Screw Tapping 7+ Crown Washer (4x)

a

a

c

 Anode Button

b

b