Sony KV-SW212M50 Service Manual ▷ View online
– 2 –
KV-SW212M50/M81/M83/M83/H/N60/P50
RM-GA002
TABLE OF CONTENTS
SELF DIAGNOSTIC FUNCTION ....................................... 3
1. DISASSEMBLY
1-1.
3D Box Removal (KV-SW212M83/M83/H) .............. 5
1-2.
Rear Cover Removal .................................................... 5
1-3.
Speaker Removal ......................................................... 5
1-4.
Chassis Assy Removal ................................................. 5
1-5.
Service Position ........................................................... 5
1-6.
Terminal Bracket and J Board Removal ..................... 5
1-7.
A Board Removal ........................................................ 6
1-8.
Picture Tube Removal .................................................. 6
2. SET-UP ADJUSTMENTS
2-1.
Beam Landing Adjustment .......................................... 8
2-2.
Convergence Adjustment ............................................. 8
2-3.
Focus Adjustment ...................................................... 10
2-4.
G2 (SCREEN) Adjustment ........................................ 10
2-5.
White Balance Adjustment ........................................ 10
2-6.
Sub Bright Adjustment .............................................. 10
3. CIRCUIT ADJUSTMENTS
3-1.
Adjustments With Commander ................................. 11
3-2.
Adjustment Method ................................................... 12
3-3.
Picture Quality Adjustment ....................................... 34
3-3-1. P MAX/Contrast Adjustment ......................... 34
3-3-2. Sub Color Adjustment .................................... 34
3-3-3. Sub Hue Adjustment ....................................... 34
3-3-1. P MAX/Contrast Adjustment ......................... 34
3-3-2. Sub Color Adjustment .................................... 34
3-3-3. Sub Hue Adjustment ....................................... 34
3-4.
Geometry Adjustment ................................................ 34
3-4-1. General Setting ............................................... 34
3-4-2. Pal 50Hz Normal Mode .................................. 34
3-4-1. General Setting ............................................... 34
3-4-2. Pal 50Hz Normal Mode .................................. 34
4. DIAGRAMS
4-1.
Block Diagram ........................................................... 36
4-2.
Circuit Boards Location ............................................ 37
4-3.
Schematic Diagram Information ............................... 37
4-3-1. A Board — (Block 001) .................................. 38
4-3-2. A Board — (Block 002) .................................. 40
4-3-3. A Board — (Block 003) .................................. 42
4-3-4. A Board — (Block 004) .................................. 44
4-3-5. A Board — (Block 005) .................................. 46
4-3-6. A Board — (Block 006) .................................. 48
4-3-7. A Board — (Block 007) .................................. 50
4-3-8. C Board Schematic Diagram .......................... 51
4-3-9. J Board Schematic Diagram ........................... 52
4-3-1. A Board — (Block 001) .................................. 38
4-3-2. A Board — (Block 002) .................................. 40
4-3-3. A Board — (Block 003) .................................. 42
4-3-4. A Board — (Block 004) .................................. 44
4-3-5. A Board — (Block 005) .................................. 46
4-3-6. A Board — (Block 006) .................................. 48
4-3-7. A Board — (Block 007) .................................. 50
4-3-8. C Board Schematic Diagram .......................... 51
4-3-9. J Board Schematic Diagram ........................... 52
4-4.
Voltage Measurement and Waveforms ...................... 53
4-5.
Printed Wiring Boards ............................................... 56
4-6.
Semiconductors .......................................................... 59
5. EXPLODED VIEWS
5-1.
Picture Tube, Speaker Bracket and Chassis .............. 61
5-2.
3D Speaker ................................................................. 61
6. ELECTRICAL PARTS LIST .............................................. 63
OPERATING INSTRUCTIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE
ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
Section
Title
Page
Section
Title
Page
– 3 –
KV-SW212M50/M81/M83/M83/H/N60/P50
RM-GA002
KV-SW212M50/M81/M83/M83/H/N60/P50
RM-GA002
The units in this manual contain a self diagnostic function. If an error occurs, the STANDBY (1) indicator will automatically
begin to flash. The number of times the STANDBY (1) indicator flashes translates to a probable source of the problem. If an
error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in
memory to reveal past problems and how often these problems occur.
begin to flash. The number of times the STANDBY (1) indicator flashes translates to a probable source of the problem. If an
error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in
memory to reveal past problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS
When an errors occurs, the STANDBY (1) indicator will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the indicator will identify the first of the problem areas.
problem. If there is more than one error, the indicator will identify the first of the problem areas.
Result for all of the following diagnosis items are displayed on screen. No error has occurred if the screen displays a "0".
SELF DIAGNOSTIC FUNCTION
Diagnosis
Item
Description
No Power
+B overcurrent
(OCP)
(OCP)
V-Protect (OVP)
IK (AKB)
Power supply
NG (+5V) for
Video Processor
NG (+5V) for
Video Processor
No. of timer
STANDBY (1)
indicator flashes
Does not light
2 times
4 times
5 times
8 times
Diagnostic Result
on screen display
on screen display
–
2:0
or
2:1 ~ 255
4:0
or
4:1 ~ 255
5:0
or
5:1 ~ 255
8:0
or
8:1 ~ 255
Probable Cause
Location
• Power cord is not plugged
in.
• Fuse is burned out (F600)
A board.
• H OUT (Q805) is shorted.
(A board)
• IC751 is shorted. (C board)
• +13V is not supplied.
(A board)
• IC804 is faulty. (A board)
• Video OUT (IC
751
) is
faulty. (
C
board)
• IC001 is faulty. (A board)
• Screen (G2) is improperly
• Screen (G2) is improperly
adjusted.
• IC604 faulty.
• IC602 faulty.
• IC602 faulty.
Detected
Symptoms
• Power does not turn on.
• No power is supplied on
• No power is supplied on
TV.
• AC Power supply is faulty.
• Power does not turn on.
• Load on power line is
• Load on power line is
shorted.
• Has entered standby state
after horizontal raster.
• Vertical deflection pulse is
stopped.
• Power line is shorted or
power supply is shorted.
• No raster is generated.
• CRT Cathode current
• CRT Cathode current
detection reference pulse
output is small.
output is small.
• No power supply to CRT
ANODE.
• No RASTER is generated.
2. STANDBY INDICATOR BLINKING PROCESS
The example above represents for 4 times blink
Lamp OFF 3 seconds
Lamp ON 300ms
Lamp OFF 300ms
3. STANDBY INDICATOR ON TV FRONT PANEL
Standby indicator
– 4 –
KV-SW212M50/M81/M83/M83/H/N60/P50
RM-GA002
[+B overcurrent $OCP%]
Occurs when an overcurrent on the +B(135V) line is detected by pin 32 of IC001 (A board).
If the voltage of pin 32 of IC001 (A board) is more than 4V, the unit will automatically go to
standby.
If the voltage of pin 32 of IC001 (A board) is more than 4V, the unit will automatically go to
standby.
[V-PROTECT]
Occurs when an absence of the vertical deflection pulse is detected by pin 13 of IC001
(A board).
(A board).
[IK $AKB%]
If the RGB levels* do not balance within 15 sec after the power is turned on, this error will be
detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.
detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.
Occurs when IC001 internal HV protect detects an abnormal H-Pulse (frequency) due to
improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be
detected. eg: IC602, IC604 go faulty.
improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be
detected. eg: IC602, IC604 go faulty.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
A BOARD
IC001
Y/CHROMA JUNGLE
A BOARD
IC804
V.OUT
A BOARD
IC001
SYSTEM
A BOARD
IC003
MEMORY
FROM
C BOARD
IC751 PIN 5
IK
EHTO
RED LED
DISPLAY
SDA1
V.GUARD
SDA
5
F.B-PLS
3
13
84
32
122
A BOARD
FROM
Q816
COLLECTOR
99
POWER SUPPLY NG (+5V)
for VIDEO PROCESSOR
for VIDEO PROCESSOR
4. SELF DIAGNOSTIC SCREEN DISPLAY
5. HANDLING SELF DIAGNOSTIC SCREEN DISPLAY
6. SELF-DIAGNOSTIC CIRCUIT
2 OCP
: 0
3 OVP
: N/A
4 VSTOP : 1
5 AKB
5 AKB
: 0
8 SVP
: 0
101 WDT : N/A
"0" means no fault has been detected.
"1" means a fault has been detected.
"N/A" means not available for this models.
SELF DIAGNOSTIC
5
8
No.
Description
Method
1.
Display self diagnostic screen
[Display] t [Channel ] t [Volume ] t [Power / TV]
Note: The above must be performed while TV is on standby mode.
2.
Stop standby flash
i) Turn off power switch on main.
ii) Unplug power cord from the outlet.
ii) Unplug power cord from the outlet.
3.
Clear fault result
In self diagnostic screen,press
[Channel ] t
-
Note: Diagnostic results display on screen is not automatically cleared. Therefore,
clear result after completion of repair.
clear result after completion of repair.
4.
Quit self diagnostic screen
Turn off power switch of remote commander or main unit.
– 5 –
KV-SW212M50/M81/M83/M83/H/N60/P50
RM-GA002
SECTION 1
DISASSEMBLY
1-3.
SPEAKER REMO VAL
1-5.
SERVICE POSITION
1-4.
CHASSIS ASSY REMO VAL
1-1.
3D BOX REMO VAL (KV-SW212M83/M83/H)
1
Two screws
(Washer Head)
(+P4 x16)
(+P4 x16)
3
Terminal bracket
1
One screw
(+
BVTP
3
×
12
)
2
One screw
(
+BVTP
4
×
16
)
4
Two screws
(
+BVTP
3
×
12
)
5
J Board
(
only for model
KV-SW212M83/M83/H)
)
1-2.
REAR COVER REMO VAL
1
Eight screws
(+BVTP 4
× 16)
2
Rear cover
1
3D Speaker box assy
2
Rear cover
1-6.
TERMINAL BRACKET AND J BOARD
REMOVAL
