DOWNLOAD Sony KV-SR29M59K Service Manual ↓ Size: 15.66 MB | Pages: 93 in PDF or view online for FREE

– 33 –

Full Surround

(Full Surround option-no for

0 = Normal Surround Model

EURO model)

1 = Full Surround Model

(Off/simulated/surround/
SRS/WOW/TruSurround)

No Surround

(No Surround Model)

0 = Surround Model, 1 = Non-Surround Model

COSMIC ASD

Automatic Standard Detection

  0 = disabled, 1 = enabled

Using COSMIC (Non-Stereo)

ASD

(Automatic Standard Detection)

0 = disabled, 1 = enabled

Tilt

(Tilt Correction/PIC Rotation)

0 = disabled, 1 = enabled

IP Plus

(Intelligent Picture Plus)

0 = disabled, 1 = enabled

IP

(Intelligent Picture)

0 = disabled, 1 = enabled

Wide

(Wide Mode/V-Compressed)

0 = disabled, 1 = enabled

Full

No

COSMIC

ASD

Tilt

IP Plus

IP

Wide

DEC

Surround Surround

ASD

0

0

0

1

1

1

1

1

31

0

0

0

1

1

1

1

1

31

0

0

0

1

1

1

1

1

31

0

0

0

1

1

1

1

1

31

0

0

1

0

1

1

1

1

47

0

0

1

0

1

1

1

1

47

0

0

1

0

1

1

1

1

47

0

0

0

1

1

1

1

1

31

0

0

0

1

1

1

1

1

31

0

0

0

0

1

1

1

1

15

– 34 –

GA US

(US Model Destination)

0 = US/CANADA/Latin
1 = Taiwan/Korea/Philippine
      (Wake-up timer enable)
      (GA Surround Spec:OFF,
      SIMULATED, SRS)

3D OSD

(BX1L Full version GA Multi

0 = Normal with 3D Intelligent picture OSD

Destination ONLY)

1 = Disable 3D Intelligent picture OSD

Feature 2

(Temporary for BX1L)

0 = Comb Not available
1 = Comb available

Feature 1

(Temporary for BX1L)

0 = PiP Not Available
1 = PiP available

OSD Language Selection

US (GA NTSC)

1x1x = Complicated Chinese
1xx1 = Korean (note: for BX1L, combination
            of C.Chinese & Korean not available)

GA

1xxx = Simplified Chinese
x1xx = Arabic
xx1x = Thai
xxx1 = Vietnamese

GA US

3D OSD

Feature 2

Feature 1

OSD Language Selection

DEC

(3D COMB)

(PIP)

0

0

1

1

0

0

1

0

50

0

0

1

1

1

0

0

0

56

0

0

1

1

1

0

0

0

56

0

0

1

1

0

0

1

0

50

0

0

1

1

1

0

0

0

56

0

0

1

1

0

1

0

0

52

0

0

1

1

0

1

0

0

52

0

0

1

1

1

0

0

0

56

0

0

1

1

0

1

0

0

52

1

0

1

0

1

0

1

0

170

– 35 –

1. Select Video.
2. Input PAL 100% Color Bar.
3. Set to following condition:

PICTURE 100%,COLOR 50%, BRIGHTNESS 50%,
HUE Center, SHP 50%.

4. Set the PICT 006 WTS to 00h.
5. Connect an oscilloscope to pin 2 (B OUTPUT) of

CN004 A Board.

6. Set the service mode and select  SADJ 004 "SCOL"

with 

1

 and 

4

 of the commander then adjust to

VB2=VB3=VB4 with 

3

 and 

6

 (For PAL), write the

data as below :
Adjusted SCOL value = X

7. Input NTSC 75% Color Bar to TV set and repeat item no.

3 to 5.

8. Set the service mode and select SADJ 004 "SCOL"

with 

1

 and 

4

 of the commander then adjust to

VB1 = VB4.
Adjusted SCOL value = Y

9. Set WTS back to original data.

VB2 = VB3 = VB4(For PAL sub color adjustment)
VB1 = VB4(For NTSC sub color adjustment)

(Difference is within 70mV)

1. Select Video.
2. Input NTSC 3.58 Color Bar to Video/TV mode.
3. Set to following condition:

PICTURE 100%,COLOR 50%, BRIGHTNESS 50%,
HUE Center, SHP 50%.

4. Connect an oscilloscope to pin 2 (B output) of CN004.
5. Set the service mode and select YC 013 "TINT" with

1

 and 

4

 of the commander then adjust to

VB1=VB2=VB3=VB4 with 

3

 and 

6

.

6. Then press [MUTING] 

t 

-

 to write the data.

7. Select TV channel with NTSC 3.58 and repeat 3-6.

VB1

VB2

VB3

VB4

VB1

VB2

VB3

VB4

VB1 = VB2 = VB3 = VB4

80mV

The highest level of VB1, VB2, VB3, VB4 must be
aligned at the same time.
The ideal difference between VB2 and VB3 is within 

±

80mV.

Picture Mode: Personal
1. Select Video mode.
2. Input PAL Color Bar toTV set.
3. Set the following condition:

PICTURE 100%, COLOR 0%,BRIGHTNESS 50%

4. Connect oscilloscope to pin 4 (R Output) of CN004,
5. Set to Service Mode PICT 003 PWL to 00h and

WHBL 017 BLBG to 01h.

6. Select SADJ 000 "PMAX" with 

1

 and 

4

 of the

commander then adjust VR within spec with 

3

 and 

6

.

7. Copy SADJ 000 PMAX (Video mode) to SADJ 000

PMAX (TV mode).

8. Select "WIDE" mode for TV & Video mode,  Write the

PMAX Data as below:

9. Set the PWL & BLBG back to (PWL: 01h and

BLBG: 00h)

VR

Black

SIZE

VIDEO MODE

RF MODE

DVD MODE

PAL

SECAM

PAL

SECAM

50Hz

25

X+2

X+2

X+2

X+2

X+6

29

X+3

X+3

X+3

X+3

X+7

34

X+4

X+6

X+6

X+6

X+8

SIZE

VIDEO MODE

RF MODE

DVD MODE

NTSC

NTSC

60Hz

25

Y+5

Y+5

Y+7

29

Y+4

Y+4

Y+6

34

Y+6

Y+6

Y+8

VR

PAL

34"

2.15

±

0.03Vpp

29"

2.15

±

0.03Vpp

25"

2.15

±

0.03Vpp

INCH

VIDEO MODE

TV MODE

WIDE

WIDE

OFF

ON

OFF

ON

SR25"

SR29"

X

X-6

X

X-6

SR34"

– 36 –

1. Set to Service Mode.
2. Input SPCB Signal (For NTSC models select Video

mode)

3. Using the 

1

 and 

4

 buttons select, category GEOM

(service mode) Raise/lower data using the 

3

 and 

6

buttons to adjust the following items:-
Service Item

GEOM:

000

HPOS

HORIZONTAL SHIFT (HS)

001

HPAR

HORIZONTAL
PARALLELOGRAM

002

HBOW

HORIZONTAL BOW

003

VLIN

VERTICAL LINEARITY

005

HSIZ

EW WIDTH (EW)

006

EWPW

EW PARABOLA/WIDTH
(PW)

007

UCOP

EW UPPER CORNER
PARABOLA

008

LCOP

EW LOWER CORNER
PARABOLA

009

EWTZ

EW TRAPEZIUM

010

VSLP

VERTICAL SLOPE (VS)

011

VSIZ

VERTICAL AMPLITUDE

012

SCOR

S-CORRECTION (SC)

013

VPOS

VERTICAL SHIFT (VSH)

4. For Korea models only:

a) For GEOM items, copy adjusted 60Hz to 50Hz
b) Add 6 steps to 50Hz "HPOS" item and save data.
c) Add 3 steps to 50Hz "HSIZ" item and save data.

(V-Compression Adjustment)
1. Input SPCB signal(For NTSC models select Video

mode)

2. Adjust condition to WIDE MODE : ON.
3. Copy (item from NORMAL MODE (50Hz) adjusted

data for the following items:

Service Item

GEOM:

003

VLIN

VERTICAL LINEARITY

010

VSLP

VERTICAL SLOPE (VS)

011

VSIZ

VERTICAL AMPLITUDE

012

SCOR

S-CORRECTION (SC)

1. Input a color with bar with 100IRE white signal to pin

1

 (CVBS) of CN2001 BC board.

2. Set to service mode and select 3D NR Bus data with

1

 and 

4

 of the commander.

3. Press [MUTING] 

t 

-

 to write the data to TC90A88F.

1. Input a color bar with 100IRE white signal to pin 1

(CVBS) of CN2001 BC board.

2. Confirm no dot structure can been seen and the

picture is normal on the screen.

3. Input signal RAMP to pin 1 (CVBS) of CN2001 BC

board.

4. Confirm no vertical stripes, no noise can be seen and

the picture is normal on the screen.

5. Adjust RV2001 (BC board) so that the output level of

CN2001 (BC board) pin 3 (YOUT) is within spec

1. Input a PAL Color Bar.
2. Press PIP button on remote commander to set PIP

position.

3. Set to service mode.
4. Use 

1

 & 

4

 of the RM to select

PIP 000 HPS (for H Picture Position),
PIP 001 VPS (V Picture Position),
PIP 002 VFP (V Fine Position),
PIP 003 HFP (H Fine Postion),

5. Adjust with 

3

 & 

6

 for best position & picture.

PRESS [MENU] button on the remote commander.
Then select [SET UP], and [PIC ROTATION].
Picture will rotate while pressing  f+, F– .
Set to CENTER position by press [TEST] + [NORMAL] on
the remote commander.

1. Receive cross hatch/dot signal
2. Adjust RV1800 on C-Board to make H-Trapezoid

distortion best.

1.4 ± 0.05 Vpp