DOWNLOAD Sony KV-SR25M53K Service Manual ↓ Size: 7.79 MB | Pages: 81 in PDF or view online for FREE

– 6 –

2 Four screws
     (+BVTP 3 

× 12 

     Type2 IT-3)

4 One screw
    (+BVTP 3 

× 12

     Type2 IT-3)

3 One screw
    (+BVTP 3 

× 12 Type2 IT-3)

1 One screw
     (+BVTP 4 

× 16 Type2 IT-3)

5 Two hooks

6 Terminal
     bracket

1  Nine screws (+BVTP 4 

× 16) Type2 IT-3

2 Rear cover

1 Two screws
     (+BVTP 4 

× 16

       Type2 IT-3)

2 Two screws
     (Washer Head) 
     (+P4x16)

1 

3D Speaker box assy

2 Rear cover

– 7 –

1 J3 Board

3 Four screws
     (+BVTP 3 

× 12 Type2 IT-3)

2 One screw
     (+BVTP 4 

× 16 Type2 IT-3)

1 F Board

2 Two clips

3 One screw     
     (+BVTP 3 

× 12 Type2 IT-3)

2 BC Board

4 Two clips

1 K Board

3 Two clips

3 Four hooks

1 Five hooks

2 H5  Board

4 H4 Board

5 Two screws
     (Washer Head) 
     (3 

× 12)(+)(BVTAP)

2 Four screws
    (3 

× 12)(+) BVTAP

3 Two hooks

1 Five 
     connectors

6 Four hooks

4 A Board

7 B  Board

– 8 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

a.

2 Using a thumb pull up the rubber cap firmly in the direc-

b.

3 When one side of the rubber cap is separated from the

c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

anode button

•

Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.

1) Remove the rear cover.
2) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.
3) Place the TV set with the CRT face down on a cushion jig.

A

A

B

B

C

4

 Anode Cap Removal

9

 Earth Coating Assy(2) Removal

qa

 Loosen the Neck Assembly 
fixing screw and remove
Neck Assy and VM board

qs

 Loosen the Deflection Yoke
fixing screw and remove

0

 C Board Removal

8

 Spring Tension 
 Removal (x2)

5

 Holder, DGC
 Removal (x2)

7

 Degaussing Coil

qf

 Screw (5) Tapping

– 9 –

The following adjustments should be made when a
complete realignment is required or a new picture tube is
installed.

Set the controls as follows unless otherwise noted:
VIDEO MODE: .................................................... Standard
PICTURE CONTROL: ......................................... Normal
BRIGHTNESS CONTROL: ................................. Normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. Screen(G2)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter
5. Oscilloscope

Preparation :
•

In order to reduce the influence of geomagnetism on
the set's picture tube, face it east or west.

•

Switch on the set's power and degauss with the
degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig 2-1.
3. Set the pattern generator raster signal to a green

raster.

4. Move the deflection yoke to the rear and adjust with

purity control so that the green is at the center and the
blue and the red take up equally sized areas on each
side. (Figures 2-2 through 2-4.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (Figure 2-2.)

6. Switch the raster signal to blue, then to red and verify

the condition.

7. When the position of the deflection yoke have been

decided, fasten the deflection yoke with the screws and
DY spacers.

8. If the beam does not land correctly in all the corners,

use a magnet to adjust it.
(Figure 2-5.)

Red

Blue

Green

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

Purity control

normal

}

......................................................................................................................................................................................................................

Neck assy

G2

G1

G3

Align the edge of
the neck assy with
the start of the G3 grid.