DOWNLOAD Sony KV-SR253M53 Service Manual ↓ Size: 11.33 MB | Pages: 77 in PDF or view online for FREE

– 12 –

Dress Conn Assy, 7P RGB; Conn Assy, 5P

Dress DY connector; Conn Assy, 4P 200V; 

Conn Assy 4P VM and Conn Ass, 6P using 

purse lock 

∅ 9 as shown.

Front In and Lead Assy, Earth using purse lock 

∅ 9.  

Keep wires away from heatsinks and high-temperature parts.

Note: Make sure DY connector is
inserted securely.-->prevent it from
coming out.

  

Purse lock 

∅ 9 

Lead Assy, Earth

Conn Assy, 5P Front In 

Purse lock 

∅ 

9 

Conn Assy, 7P RGB

Keep Conn Assy, 5P Front In wire in an

upward path from CN9201 to where it is

dressed with purse lock 

∅ 9. This is to keep 

it away from deflection area.

 

DY

 Connector

Conn Assy

, 

6P

Conn Assy

, 

4P 

200V

Purse lock 

∅ 9 

Conn Assy

, 

4P

 VM

Conn Assy, 6P

DY 

Conn

Conn 

Assy, 4P 

Purse lock 

∅ 9  

Conn 

Assy, 

4P 200V

Keep Conn Assy, 5P Front In wire in an

upward path from CN9201 to where it is

dressed with purse lock 

∅ 9. This is to keep

it away from deflection area.

– 13 –

Avoid any stress on Lead Assy, G2; Lead Assy, Focus
and terminal at W7001.

Install Rotation Coil as shown.
1) Coil positioned in clockwise direction.
2) Wire is at 3 o'clock position. 

Dress Lead Assy, Speaker to center position of Rotation coil using purse lock 

∅ 9 as shown. 

Make sure Earth Assy, Couting wire is above Lead Assy, Speaker.
This is to keep Lead Assy, Speaker away from Deflection Yoke.

Rotation coil conn is

 

dressed outside and below

 

Earth Assy, Coating wires.

Earth Assy,

Coating

wires

Wire from Rotation

DY

Dress Rotation Coil

connector together

with Lead Assy,

G2; Lead Assy

Focus and Conn

Assy, 4P 200V

using pin, wire

A707

 

 

 

 

Lead Assy, G2

W7001

CN1802

 

Conn Assy, 

4P 200V

Lead Assy,

Focus

Keep wire

away

from

R781

 

A715

A713

Prevent wires
from touching

rear cover or any

enclosures by

turning them

away from it -->

avoid rattle

sound.

 

 

Prevent wires from

touching rear cover or

any enclosures by

turning them away

from it --> avoid rattled

 

∅ 9

Rotation 

coil

Earth Assy, Coating

wire is above

Lead Assy,

Speaker

Dress Lead Assy,
Speaker to center

position of Rotation Coil

using purse lock 

∅ 9 

 

Earth Assy,

Coating wire

Lead Assy,

Speaker

Purse lock 

∅ 
9 

Lead Assy, Speaker

(RED+BLK)

Rotation Coil 

DGC connector

DG

DGC

right spk

Khoùa 1

1

Degauss

Rotation Coil

DY

Attach purse lock 

∅ 9 

here

 

Lead Assy,

Speaker

Rotation 

Coil 

Keep wire

away

from R781

and heatsinks

A713, A715.

Rotation Coil

– 14 –

Dress cap assy, High voltage with holder, HV cable combi
as shown. 

Install Cap Assy, High voltage as shown.

Caution: 1) Make sure the specified position is being followed.
              2) Position the Cap Assy, High Voltage in the inner  
                  ring of the Holder, HV cable combi (see diagram).

Install AC cord holder to AC power cord at specified 
position as shown.

TVSR Requirement:
1. Keep HV cable away from conductive parts
    (distance of 1mm/kV). 
2. Keep spacing between edge of anode cap & conductive parts
    (distance of 0.5mm/kV).
3. Keep spacing between edge of anode cap & non-conductive 
    parts (distance of at least 5mm or more).

Top view 

DGC

Inner Ring

Rotation coil

Side hook

Large hook

Purse lock 

φ 9 

250 ± 5 mm 

Holder, HV cable 

HV cap

Dress Holder, HV Cable Combi to

Cap Assy, High Voltage and attach

side hook to rotation coil at 10

o'clock position. Then, attach large

hook to DGC and dress with

purse lock 

φ 9. 

10 o'clock

Purse lock 

φ 9 

 

Keep distance of HV

cable from other

wires, conductive

parts and

CRT's carbon area

Side hook

Min. distance =

1mm/kV

Large hook

P-P taping 

of DGC

 

Min. distance =

1mm/kV

Dress using Purse lock 

φ 

CRT's carbon area

 360  + 5 mm 

Attach AC cord

onto holder and
insert to bottom

cover

 

Hook

TVSR requirement:
 1. Spacing between HV cable and other conductive partís surface

 

     is 1mm/kV or more.

2. Spacing between HV cable's and enclosure with ventilation or 

 

    the edge where terminal bracket and rear cover meet: 10 mm
    or more. 

CAUTION:
Please ensure that the portion of HV cable above  
the Holder, HV Cable Combi is kept away from CRT's carbon area.

Also, portion of HV cable below the Holder, HV Cable Combi needs
 to be kept away from conductive parts (DGC, rotation coil, CRT's

carbon area, speaker wire, etc).

Ensure forming of HV cable is OK and no unnatural curve occurs.
Do not twist or loop the cable.

DGC

HV

DGC Band

Rotation coil

CRT's carbon area

Dress Holder, HV

Cable Combi to

the right of P-P
taping of DGC.

Dress purse lock

 

φ 9 to the right of

large hook on

Holder, HV Cable

Combi.

– 15 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position Neck Assy as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

Purity control

Neck assy

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.