Sony KV-PG14N70 Service Manual ▷ View online
– 5 –
KV-PG14N70
RM-915
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
3. STOPPING THE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER
lamp from flashing.
lamp from flashing.
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be con-
firmed, it is possible to bring up past occurances of failure for confirmation on the screen:
firmed, it is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] / channel [5] / Sound volume [-] / Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
STANDBY/SLEEP lamp
Lamp ON 0.3 sec.
Lamp OFF 3 sec.
Lamp OFF 0.3 sec.
2 times
4 times
Diagnostic Item
Flash Count*
+B overcurrent/overvoltage
2 times
Vertical deflection stopped
4 times
* One flash count is not used for self-diagnostic.
002 : 000
004 : 000
004 : 000
Numeral "0" means that no fault has been detected.
101 : 000
SELF DIAGNOSTIC
– 6 –
KV-PG14N70
RM-915
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic
screen during repairs. When you have completed the repairs, clear the result display to “0”.
screen during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the
diagnostic screen is being displayed.
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the
diagnostic screen is being displayed.
Channel [8]
/ 0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
6. SELF-DIAGNOSTIC CIRCUIT
[+B overcurrent ªOCPº]
Occurs when an overcurrent on the +B(135) line is detected by Q500. If Q500 go to
ON and the voltage to pin 50 of IC301 more than 3.5V when V.SYNC is more than
seven verticals in a period, the unit will automatically turn off.
ON and the voltage to pin 50 of IC301 more than 3.5V when V.SYNC is more than
seven verticals in a period, the unit will automatically turn off.
[Vertical deflection stopped]
Occurs when an absence of the vertical deflection pulse is detected by Pin 17 and
IC001 shut down the power supply.
IC001 shut down the power supply.
[White balance failure]
If the RGB levels* do not balance or become low level within 5 seconds, this error
will be detected by IC301. TV will stay on, but there will be no picture.
will be detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
IC301
Y/CHROMA JUNGLE
IC001
SYSTEM
IC003
MEMORY
MP/
PROTECT
PROTECT
II-DAT1
DAT
II-DATO
5
50
54
SDA
8
FROM
[+B] Q500
[+B] Q500
17
[V]
D553
D553
53
– 10 –
KV
-PG14N70
-PG14N70
RM-915
2-6. TERMINAL BRACKET REMOVAL
SECTION 2
DISASSEMBLY
2-1. REAR COVER REMOVAL
2-2. SPEAKER REMOVAL
2-3. CHASSIS ASSY REMOVAL
1 Eight screws
(+BVTP 4
× 16)
1 Rear Cover
1 Four screws
washer head
(BVTP 3
(BVTP 3
× 12)
CRT SUPPORT BLOCK
Speaker
Push claw
2-5. SERVICE POSITION
Caution:
Do not take out CRT support block while TV set in
standing position.
Note:
Undress necessary wires that creates tension while
placing the chassis into Service Position.
F Board
Bracket F1 PC Board
1 One screw
(+BVTP 4
× 16)
2 Terminal Bracket
2-4. F BOARD REMOVAL
–
11
–
KV
-PG14N70
-PG14N70
RM-915
2-7. REPLACEMENT OF PARTS
For replacements of light guide,unscrew them, exchange with
new parts and fix them with screws respectively.
new parts and fix them with screws respectively.
2-7-2. Replacement of Power Button
2-7-1. Replacement of Light Guide
2-8. PICTURE TUBE REMOVAL
Note:
Note:
•
Please make sure the TV set is not in standing position before removing necessary
CRT support located on bottom right and left.
CRT support located on bottom right and left.
One screw
(+BVTP 3
(+BVTP 3
× 12)
1
Push to direction of arrow
and remove
and remove
7
5
8
Demagnetic coil
1 Four screws
(washer head)
(BVTP 3
(BVTP 3
× 12)
4
Two screws
(Tapping 5+
Crown Washer)
(Tapping 5+
Crown Washer)
2 Speaker
(5
× 9cm)
0Tension
Beznet
hook
hook
spring
Chassis assy
Deflection
yoke
yoke
C board
Coating earth assy
!¢
Picture tube
!£ Cushion
3Two screws
(Tapping 5 +
Crown Washer)
Crown Washer)
6
Holder DGC
Cushion DGC
Cushion DGC
!™
!∞
!¡
A Board
Slim Beznet
CRT Support Block
9
Anode
cap
cap
Click on the first or last page to see other KV-PG14N70 service manuals if exist.