DOWNLOAD Sony KV-PG14N70 (serv.man2) Service Manual ↓ Size: 3.81 MB | Pages: 43 in PDF or view online for FREE

– 9 –

J Presetting channels

You can automatically preset cable TV, VHF or UHF broadcast channels, or
manually preset the channels to receive new channels or channels with a weak
signal.

Press ! on the TV to turn on the TV.

Press CABLE to select “CABLE: ON”.

Press AUTO PROGRAM on the remote or press
SELECT and CHANNEL + on the TV at the same
time for one to two seconds to preset the
channels automatically.

Press the number buttons to select the desired
channel number, then press ENT.

Press ADD/ERASE.

“+” appears beside the channel number,
indicating that presetting is complete.

Notes
• If you select “CABLE: ON”, you will be able to receive 125 cable TV channels. If there are no

cable TV channels, you will receive VHF broadcast channels.

• If you select “CABLE: OFF ”, you will be able to receive 68 VHF or UHF broadcast channels

only.

TV

1

2

3

4

6

7

8

9

0

5

ENT

FAVORITE

WAKE UP

SLEEP

JUMP

CABLE

DISPLAY

MUTING

POWER

MTS

VOL

CH

VIDEO

SOUND

MODE

AUTO

PROGRAM

ADD/

ERASE

TV

If the color is abnormal when receiving programs through the video input terminal.

(1) Press SELECT until “COLOR SYS” appears on the screen.

(2) Press + or – to select the appropriate color system until the color is optimal.

(1) Press CH +/– until the unused or unwanted channel number appears on the

screen.

(2) Press ADD/ERASE to skip the unused or unwanted channel number.

“–” appears beside the channel number, indicating that disabling is complete.

Note
• To restore the skipped channel number again, preset the channel automatically or manually.

K

You can customize the picture by selecting the picture mode or by adjusting its
settings.

  Press PIC MODE to select the desired picture mode.

“DYNAMIC”

view high contrast pictures.

“STANDARD”

view normal contrast pictures.

“SOFT”

view mild pictures.

  

Press SELECT until the desired setting appears.

Each time you press SELECT, the setting item will
change as follows:

Press + or – to adjust the item.

To adjust other items, repeat steps 1 to 2.

Notes
• “HUE” can be adjusted for the NTSC color system only.
• Reducing “SHARP” can also reduce picture noise.

TV

1

2

3

4

6

7

8

9

0

5

ENT

FAVORITE

WAKE UP

SLEEP

JUMP

CABLE

DISPLAY

MUTING

POWER

MTS

VOL

CH

VIDEO

SOUND

MODE

AUTO

PROGRAM

ADD/

ERASE

TV

–

 10 

–

For replacements of light guide,unscrew them, exchange with
new parts and fix them with screws respectively.

One screw
(+BVTP 3 

× 12)

1

Push to direction of arrow 
and remove

1 Eight screws

(+BVTP 4 

× 16)

1 Rear Cover

1 Four screws 

(BVTP 3 

× 12)     

CRT SUPPORT BLOCK

Speaker

Push claw

 Do not take out CRT support block while TV set in

standing position.

 Undress necessary wires that creates tension while

placing the chassis into Service Position.

1 One screw

(+BVTP 4 

× 16)

2 Terminal Bracket

–

 11 

–

•

Please make sure the TV set is not in standing position before removing necessary
CRT support located on bottom right and left.

!£

!º

!™

Demagnetic coil

2 Four screws 

(BVTP 3 

× 12)

4

Two screws
(Tapping 5+
Crown Washer)

3 Speaker

(5 

× 9cm)

7Tension

Beznet
hook

spring

Chassis assy

Deflection
yoke

C board

Coating earth assy

!∞

Picture tube

1 Cushion

5 Two screws

(Tapping 5 +
Crown Washer) 

!¡ Holder DGC

Cushion DGC

  Cushion DGC

9

 

!¢

8

A Board

Slim Beznet

CRT Support Block

6

Anode 
cap

•REMOVAL OF ANODE-CAP

NOTE : After removing the anode, short circuit the anode of the picture tube and

the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.

•REMOVING PROCEDURES

1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.

3 Do not turn the foot of rubber over too hard.

• HOW TO HANDLE AN ANODE-CAP

3 When one side of the rubber cap is separated from the anode button,  the anode-cap

can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow c.

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.

1 Turn up one side of the rubber cap in the direction indicated by the arrow a.

a

a

b

b

Anode button

c

– 12 –

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise

noted:

PICTURE control ...........................................................  normal

BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Pattern Generator

2. Degausser

3. Oscilloscope

................................................................................................................................................................................................................................

normal

In order to reduce the influence of geomagnetism on the
set's picture tube, face it east or west.
Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Set the pattern generator raster signal to a green raster.
3. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 3-1 through 3-4.)

4. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 3-1.)

5. Switch the raster signal to blue, then to red and verify the

condition.

6. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

7. If the beam does not land correctly in all the corners, use a

magnet to adjust it.
(See Figure 3-4.)

}

Purity control

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

c

d

b

c

d

a