Sony KV-PG14M40 (serv.man2) Service Manual ▷ View online
– 5 –
KV-PG14M40
RM-952
2. DISPLAY OF STANDBY (1) INDICATOR LIGHT FLASH COUNT
3. STOPPING THE STANDBY (1) INDICATOR FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY (
1
)
indicator from flashing.
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be con-
firmed, it is possible to bring up past occurances of failure for confirmation on the screen:
firmed, it is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] /
channel
[5] /
Sound volume
[-] /
Power ON
˘
Note that this differs from entering the service mode (mode volume
[+]
).
Self-Diagnostic screen display
STANDBY/SLEEP lamp
Lamp ON 0.3 sec.
Lamp OFF 3 sec.
Lamp OFF 0.3 sec.
2 times
4 times
Diagnosis Item
Flash Count*
+B overcurrent/overvoltage
2 times
Vertical deflection stopped
4 times
* One flash count is not used for self-diagnosis.
002 : 000
004 : 000
004 : 000
Numeral "0" means that no fault has been detected.
101 : 000
SELF DIAGNOSTIC
– 6 –
KV-PG14M40
RM-952
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnosis results displayed on the screen are not automatically cleared, always check the self-diagnostic
screen during repairs. When you have completed the repairs, clear the result display to “0”.
screen during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnosis function will not be able to detect subsequent faults after
completion of the repairs.
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the
diagnostic screen is being displayed.
diagnostic screen is being displayed.
Channel
[8] /
0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
6. SELF-DIAGNOSIS CIRCUIT
[+B overcurrent OCP]
Occurs when an overcurrent on the +B(135) line is detected by Q500. If Q500 go to
ON and the voltage to pin 50 of IC301 more than 3.5V when V.SYNC is more than
seven verticals in a period, the unit will automatically turn off.
ON and the voltage to pin 50 of IC301 more than 3.5V when V.SYNC is more than
seven verticals in a period, the unit will automatically turn off.
[Vertical deflection stopped]
Occurs when an absence of the vertical deflection pulse is detected by Pin 17 and
IC001 shut down the power supply.
IC001 shut down the power supply.
[White balance failure]
If the RGB levels* do not balance or become low level within 5 seconds, this error
will be detected by IC301. TV will stay on, but there will be no picture.
will be detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
IC301
Y/CHROMA JUNGLE
IC001
SYSTEM
IC003
MEMORY
MP/
PROTECT
PROTECT
O-LED
IO-8DAT
B-DAT
IO-SDAT
5
50
51
54
SDA
8
FROM
[+B]
Q500
17
[V]
D553
53
– 7 –
KV-PG14M40
RM-952
SECTION 1
GENERAL
A
Getting Started
Plug in the power cord, then press
! on the TV to
turn it on.
Press SELECT and PROGR + on the TV at the same time
for one to two seconds to preset the channels
automatically. (See
for one to two seconds to preset the channels
automatically. (See
J)
Tip
• To stop the automatic channel presetting, press SELECT.
• To stop the automatic channel presetting, press SELECT.
Press SELECT on the remote until “
/
LANGUAGE:
” appears on the screen, then
press + or – to change the on-sceen display language.
Connect the antenna cable (not supplied) to
8
(antenna input) at the rear of the TV.
Tip
• You can also connect your TV to other optional components.
• You can also connect your TV to other optional components.
(See
E)
Step 1
Insert the batteries (supplied) into the remote.
Note
• Do not use old batteries nor use different types of batteries
• Do not use old batteries nor use different types of batteries
together.
Step 2
Step 3
Step 4
Step 5
b
b
PROGR
SELECT
SELECT
B
WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 110 – 240 V AC.
• Do not plug in the power cord until you have completed making all other connections;
• TV operating voltage: 110 – 240 V AC.
• Do not plug in the power cord until you have completed making all other connections;
otherwise a minimum leakage current might flow through the antenna and other terminals to
ground.
ground.
• To avoid battery leakage and damage to the remote, remove the batteries from the remote if
you are not going to use it for several days. If any liquid that leaks from the batteries touches
you, immediately wash it away with water.
you, immediately wash it away with water.
Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.
falls into it. Have it checked immediately by
qualified personnel only.
Do not open the cabinet and the rear cover of the
TV as high voltages and other hazards are present
inside the TV. Refer servicing and disposal of the
TV to qualified personnel.
TV as high voltages and other hazards are present
inside the TV. Refer servicing and disposal of the
TV to qualified personnel.
Your TV is recommended for home use only.
Do not use the TV in any vehicle or where it may
be subject to excessive dust, heat, moisture or
vibrations.
Do not use the TV in any vehicle or where it may
be subject to excessive dust, heat, moisture or
vibrations.
Do not block the ventilation openings of the TV.
Do not install the TV in a confined space, such as
a bookcase or built-in cabinet.
Do not install the TV in a confined space, such as
a bookcase or built-in cabinet.
For children’s safety, do not leave children alone
with the TV. Do not allow children to climb onto it.
with the TV. Do not allow children to climb onto it.
Clean the TV with a dry and soft cloth. Do not
use benzine, thinner, or any other chemicals to
clean the TV. Do not scratch the picture tube.
use benzine, thinner, or any other chemicals to
clean the TV. Do not scratch the picture tube.
For your own safety, do not touch any part of the
TV, the power cord and the antenna cable during
lightning storms.
TV, the power cord and the antenna cable during
lightning storms.
Do not place any objects on the TV. The apparatus
shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
!
PROGR
SELECT
(MONO)
L
L(MONO)
R
★
8
6
1
3
4
7
9
2
5
0
qa
qs
R
★
D
TV front and rear panels
TV front panel
TV rear panel
Button
Function
1
!
Turn off or turn on the TV.
2
Remote control sensor.
3
1
Standby indicator.
3
Wake Up indicator.
4
PROGR +/–
Select program number.
5
2 +/– *
Adjust volume.
6
t
Select TV or video input.
7
SELECT
Select the desired item.
8
i
Headphone terminal. (KV-TG21M80 only)
8
Earphone terminal. (KV-PG14M40 only)
9
,
qa
t
Video input terminal.
0
8
Antenna input terminal.
qs
T
Monitor output terminal.
* You can also use the
2 +/– buttons on the TV to work as the +/– buttons on the remote.
★
The R (audio input) jacks are available for KV-TG21M80 only.
C
Securing the TV
B
KV-TG21M80 only
To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV.
Screw the band to the TV stand and to the
provided hole at the rear of your TV.
provided hole at the rear of your TV.
(1) Put a cord or chain through the
clamps.
(2) Screw one clamp to a wall or pillar
and the other clamp to the provided
hole at the rear of your TV.
hole at the rear of your TV.
Note
• Use only the supplied screws. Use of other screws may damage the TV.
• Use only the supplied screws. Use of other screws may damage the TV.
20 mm
3.8 mm
screws
clamps
band
or
Do not plug in too many appliances to the same
power socket. Do not damage the power cord.
power socket. Do not damage the power cord.
Pull the power cord out by the plug. Do not pull
the power cord itself. Even if your TV is turned
off, it is still connected to the AC power source
(mains) as long as the power cord is plugged in.
Unplug the TV before moving it or if you are not
going to use it for several days.
the power cord itself. Even if your TV is turned
off, it is still connected to the AC power source
(mains) as long as the power cord is plugged in.
Unplug the TV before moving it or if you are not
going to use it for several days.
WARNING (continued)
Install the TV on a stable TV stand and floor
which can support the TV set weight. Ensure that
the TV stand surface is flat and its area is larger
than the bottom area of the TV.
which can support the TV set weight. Ensure that
the TV stand surface is flat and its area is larger
than the bottom area of the TV.
To prevent fire or shock hazard, do not expose the
TV to rain or moisture.
TV to rain or moisture.
The operating instruction mentioned here are partial
abstracts from the Operating Instruction Manual. The
page numbers of the Operating Instruction Manual
remain as in the manual.
abstracts from the Operating Instruction Manual. The
page numbers of the Operating Instruction Manual
remain as in the manual.
– 8 –
KV-PG14M40
RM-952
(MONO)
L
R
L(MONO)
R
★
★
E
Connecting optional components
Connecting to the video input terminal (
t )
TV front panel
Camcorder
Audio/Video cable
(not supplied)
Note
• Do not connect video equipment to
• Do not connect video equipment to
t (video input) at the front and the rear of your TV at
the same time; otherwise the picture will not be displayed properly on the screen.
Connecting to the monitor output terminal (
T)
TV rear panel
VCR
Video game
equipment
VCR
Audio system
Audio/Video cable
(not supplied)
TV rear panel
Antenna cable
(not supplied)
★
L(MONO)
R
Audio/Video cable
(not supplied)
★
The R (audio input) jacks are available for KV-TG21M80 only.
F
Troubleshooting
If you find any problem while viewing your TV, please check the following
guide. If any problem persists, contact your Sony dealer.
guide. If any problem persists, contact your Sony dealer.
Snowy picture,
noisy sound
Good picture,
noisy sound
No picture,no sound
Good picture, no sound
Dotted lines or stripes
Double images or
“ghosts”
No color
Abnormal color
patches
The
1 (standby)
indicator on your TV
flashes red several
times after every
three seconds.
TV cabinet creaks.
A "boom" sound is
heard when the TV is
turned on.
Symptom
Solutions
• Check the antenna cable and connection on the TV, VCR and on the wall.
• Preset the channel manually again. (See
• Preset the channel manually again. (See
J)
• Check the antenna setup. Contact a Sony dealer for advice.
• Select the appropriate TV system. (See
J)
• Check the power cord, antenna and the VCR connections.
• Press
• Press
?/1 (power) or ! (main power) to turn on the TV.
• Press
2 + to increase the volume level.
• Press
% to cancel the muting.
• Do not use a hair dryer or other equipment near the TV.
• Check the antenna setup. Contact a Sony dealer for advice.
• Check the antenna setup. Contact a Sony dealer for advice.
• Use the fine tuning ("FINE") function. (See
J)
• Turn off or disconnect the booster if it is in use.
• Check the antenna setup. Contact a Sony dealer for advice.
• Check the antenna setup. Contact a Sony dealer for advice.
• Select the appropriate color system. (See
J)
• Adjust the color level. (See
K)
• Check the antenna setup. Contact a Sony dealer for advice.
• Keep external speakers or other electrical equipment away from the TV.
Press
! (main power) to turn off the TV for about 15 minutes, then turn
it on again to demagnetize the TV.
• Count the number of times the
1 (standby) indicator flashes. Press !
(main power) to turn off your TV. Contact your nearest Sony service
center.
center.
• Changes in room temperature sometimes make the TV cabinet expand or
contract, making a noise. This does not indicate a malfunction.
• The TV's demagnetizing function is working. This does not indicate a
malfunction.
G
Specifications
Power requirements
110-240 V AC, 50/60 Hz
Power consumption (W) Indicated on the rear of the TV
Television system
B/G, I, D/K, M
Color system
PAL, PAL 60, SECAM,
NTSC3.58, NTSC4.43
NTSC3.58, NTSC4.43
Channel coverage
B/G
VHF : E2 to E12
UHF : E21 to E69
CATV : S01 to S03, S1 to S41
UHF : E21 to E69
CATV : S01 to S03, S1 to S41
I
UHF : B21 to B68
CATV : S01 to S03, S1 to S41
CATV : S01 to S03, S1 to S41
D/K
VHF : C1 to C12, R1 to R12
UHF : C13 to C57, R21 to R60
CATV : S01 to S03, S1 to S41, Z1 to Z39
UHF : C13 to C57, R21 to R60
CATV : S01 to S03, S1 to S41, Z1 to Z39
M
VHF : A2 to A13
UHF : A14 to A79
CATV : A-8 to A-2, A to W+4, W+6 to W+84
UHF : A14 to A79
CATV : A-8 to A-2, A to W+4, W+6 to W+84
8 (Antenna)
75-ohm external terminal
Audio output (Speaker)
3W + 3W
3W
Number of terminal
(Video)
Input: 2* Output: 1
Phono jacks; 1 Vp-p, 75 ohms
* One input line
available
(Audio)
Input: 2* Output: 1
Phono jacks; 500 m Vrms
* One input line
available
i
(Headphone)
Output: 1
–
Stereo minijack
(Earphone)
–
Output: 1
Monaural minijack
Picture tube
21 in.
14 in.
Tube size (cm)
54
37
Measured diagonally
Screen size (cm)
51
34
Measured diagonally
Dimensions (w/h/d, mm)
497
× 458 × 487
375
× 346 × 411
Mass (kg)
25
12
Design and specifications are subject to change without notice.
Note
KV-TG21M80
KV-PG14M40
H
Remote control
Button
Function
1
?/1
Turn off temporarily or
turn on the TV.
turn on the TV.
2
a
Display the TV program.
3
JUMP
Jump to previous
program number.
program number.
4
PROGR +/–
Select program number.
5
2 +/–
Adjust volume.
6
SELECT
Select the desired item.
7
PIC MODE
Select picture mode.
9
+/–
Adjust items.
0
Display on-screen
information.
information.
qa
%
Mute the sound.
qd
t
Select TV or video input.
qf
0 – 9,
÷
Input numbers.
Timer operations
qj
Set TV to turn on
automatically.
automatically.
qk
Set TV to turn off
automatically
automatically
Sound mode operations
(KV-TG21M80 only)
(KV-TG21M80 only)
qg
SOUND MODE
Select sound mode.
qh
A/B
Not function for your TV.
Teletext operations (green label)
8
x
(red, green,
yellow, blue)
0
qs
qd
Not function for your TV.
qh
qj
qk
ql
FAVORITE
Not function for your TV.
See
–
–
–
–
–
–
–
K
–
–
–
–
–
–
–
I
I
K
–
–
TV
1
2
3
4
6
7
8
9
-
0
5
JUMP
SOUND
MODE
FAVORITE
PROGR
2
qa
0
qs
qd
qd
qf
qg
qh
qj
qk
ql
8
9
7
6
5
4
3
2
1
Click on the first or last page to see other KV-PG14M40 (serv.man2) service manuals if exist.