DOWNLOAD Sony KV-PG14L70 Service Manual ↓ Size: 3.15 MB | Pages: 42 in PDF or view online for FREE

– 9 –

TV

1

2

3

4

6

7

8

9

-

0

5

JUMP

SOUND 

MODE

 

FAVORITE

PROGR

2

J

You can automatically preset up to 100 TV channels in numerical sequence
from program number 1, or manually preset desired channels and channels
that cannot be preset automatically.

Press SELECT until “AUTO PROGRAM” appears
on the screen.

Press + or – once to enter the “AUTO
PROGRAM” mode.

The on-screen display will start flashing.

Press PROGR +/– or the number buttons until
the desired program number appears on the
screen.

Press + or – to start presetting channels
automatically.

Press SELECT until “MANUAL PROGRAM”
appears on the screen.

Press + or – once to enter the “MANUAL
PROGRAM” mode.

Press PROGR +/– or the number buttons until
the desired program number appears on the
screen.

Press + or – until the desired channel picture
appears on the screen.

To preset other channels manually, repeat steps
3 to 4.

If the color is abnormal when receiving programs through the 8 (antenna) terminal
or the t (video input) terminal

(1) Press SELECT until “COLOR SYS” appears on the screen.

(2) Press + or – to select the appropriate color system until the color is optimal.

(1) Press PROGR +/– or the number buttons until the unused or unwanted program

number appears on the screen.

(2) Press SELECT until “MANUAL PROGRAM” appears on the screen.

(3) Press + or – once to enter the “MANUAL PROGRAM” mode.

(4) Press PIC MODE to skip the unused or unwanted program number.

(5) Press SELECT to exit the “MANUAL PROGRAM” mode.

Note
• To restore the skipped program number again,  preset the channel automatically or manually.

The fine tuning (FINE) function may help to reduce the following problems:  double
images and lines moving across the TV screen.

You can use the fine tuning function as below:

(1) Select the program number you want to adjust.

(2) Press SELECT until “MANUAL PROGRAM” appears on the screen.

(3) Press + or – once to enter the “MANUAL PROGRAM” mode.

(4) Press   to display “FINE” on the screen.

(5) Press + or – continuously until the above problems are minimized.

The + or – icon on the screen flashes while tuning.

(6) Press SELECT to exit the “MANUAL PROGRAM” mode.

TV

1

2

3

4

6

7

8

9

-

0

5

JUMP

SOUND 

MODE

 

FAVORITE

PROGR

2

K

You can customize the picture by selecting the picture mode or by adjusting its
settings.

  Press PIC MODE to select the desired picture mode.

“DYNAMIC”

view high contrast pictures.

“STANDARD”

view normal contrast pictures.

“SOFT”

view mild pictures.

  

Press SELECT until the desired setting appears.

Each time you press SELECT, the setting item will
change as follows:

Press + or – to adjust the item.

To adjust other items, repeat steps 1 to 2.

Notes
• “HUE” can be adjusted for the NTSC color system only.
• Reducing “SHARP” can also reduce picture noise.

– 10 –

For replacements of light guide,unscrew them, exchange with
new parts and fix them with screws respectively.

One screw
(+BVTP 3 

× 12)

1

Push to direction of arrow 
and remove

1 Seven screws

(+BVTP 4 

× 16)

1 Rear Cover

1 Four screws 

washer head
(BVTP 3 

× 12)     

CRT SUPPORT BLOCK

Speaker

Push claw

 Do not take out CRT support block while TV set in

standing position.

 Undress necessary wires that creates tension while

placing the chassis into Service Position.

1 One screw

(+BVTP 4 

× 16)

2 Terminal Bracket

–

 11 

–

•

Please make sure the TV set is not in standing position before removing necessary
CRT support located on bottom right and left.

!™

 

!£

8

Demagnetic coil

4 Four screws 

(washer head)
(BVTP 3 

× 12)

!º

Two screws
(Tapping 5+
Crown Washer)

3 Speaker

(5 

× 9cm)

6 Tension

spring

7

Chassis assy

5 Deflection

yoke

2

CV board

1

Anode cap

Coating earth assy

!∞

Picture tube

!¢ Cushion

9Two screws

(Tapping 5 +
Crown Washer) 

!¡

Holder DGC

Cushion (50x550) DGC

  Cushion (35x250) DGC

A Board

Slim Beznet

CRT Support Block

Screw Location

•REMOVAL OF ANODE-CAP

NOTE : After removing the anode, short circuit the anode of the picture tube and

the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.

•REMOVING PROCEDURES

1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.

3 Do not turn the foot of rubber over too hard.

• HOW TO HANDLE AN ANODE-CAP

3 When one side of the rubber cap is separated from the anode button,  the anode-cap

c.

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.

1 Turn up one side of the rubber cap in the direction indicated by the arrow a.

a

a

b

b

Anode button

c

– 12 –

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise

noted:

PICTURE control ...........................................................  normal

BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Pattern Generator

2. Degausser

3. Oscilloscope

................................................................................................................................................................................................................................

normal

In order to reduce the influence of geomagnetism on the
set's picture tube, face it east or west.
Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Set the pattern generator raster signal to a green raster.
3. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 3-1 through 3-4.)

4. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 3-1.)

5. Switch the raster signal to blue, then to red and verify the

condition.

6. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

7. If the beam does not land correctly in all the corners, use a

magnet to adjust it.
(See Figure 3-4.)

}

Purity control

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

c

d

b

c

d

a