DOWNLOAD Sony KV-J25MF8J Service Manual ↓ Size: 5.32 MB | Pages: 52 in PDF or view online for FREE

– 13 –

1

 

Two screws

     (+BVTP4 x16)

1

 

Two screws

    (+BVTP4 x16)

$

 

Two screws

(Tapping 7+Crown
  Washer)

$

 

Two screws

(Tapping 7+Crown
  Washer)

@ DGC

! DGC clip

[KV-J29MF8J]

9 Two DGC band

6 C2 Board

0 Two DGC holder

[KV-J29MF8J]

0 Two DGC holder

! DGC clip

7 Neck assy

@ DGC

8 Deflection yoke

# Tension spring

4 Anode cap

Cushion

2 Speaker          

      bracket(L)assy

2 Speaker          

      bracket(R)assy

3 Speaker (5cm)

3 Speaker (5cm)

% Picture tube

5 Chassis assy

     [KV-J29MF8J]
    

     [KV-J29MF8J ]
    

   [KV-J25MF8J]

1 Two connector

5 connector

6 connector

4 Two Flat

cables

2 Two

claws

8 H3 Board

7 Two claws

3 F1 Board

– 14 –

NOTE :

Short circuit the anode of the picture tube and the anode cap

to the metal chassis, CRT shield or carbon paint on the CRT,

after removing the anode.

a

1

Turn up one side of the rubber cap in the direction

indicated by the arrow 

a

.

b

b

2

Using a thumb pull up the rubber cap firmly in the direction
indicated by the arrow 

b

.

Anode button

c

3

When one side of the rubber cap is separated from the
anode button, the anode-cap can be removed by turning
up the rubber cap and pulling up it in the direction of the
arrow 

c

.

1

Don't hurt the surface of anode-caps with sharp shaped
material!

2

Don't press the rubber hardly not to hurt inside of anode-
caps!  A material fitting called as shatter-hook terminal
is built in the rubber.

3

Don't turn the foot of rubber over hardly! The shatter-
hook terminal will stick out or hurt the rubber.

– 15 –

.................................................................................................................................................................................................................................

}

normal

G2

G1

G3

Behind the G1 edge

Neck assy

Green

Red

Blue

Disk magnets or rotatable
disk magnets correct these
areas (a-b).

a

b

c

d

c

b

a

d

Deflection yoke positioning
corrects these areas.

•

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

•

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switch should be set as follows unless otherwise noted:

PICTURE control ..........................................................  RESET

BRIGHTNESS control ...............................................  CENTER

•

In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

•

Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast

Brightness

2. Position neck ass'y as shown in Fig3-2.

3. Set the pattern generator raster signal to a red raster.

4. Move the deflection yoke to the rear and adjust with the  purity

control so that the red is at the center and the blue and the green

take up equally sized areas on each side.

(See Figures 3-1 through 3-3.)

5. Move the deflection yoke forward and adjust so that the entire

screen is red. (See Figure 3-1.)

6. Switch the raster signal to blue, then to green and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.

(See Figure 3-4.)

Perform the adjustments in order as follows :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Color-bar/Pattern Generator

2. Degausser

3. Oscilloscope

Purity control
corrects this area.

– 16 –

•

Before starting this adjustment, adjust the focus, horizontal size

and vertical size.

•

Minimize the brightness setting.

•

Provide dot pattern.

1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue points are on top of each other at the center

of the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the red,

green and blue points are on top of each other at the center of

the screen.

3. If the H.STAT variable resistor cannot bring the red, green and

blue points together at the center of the screen, adjust the hori-

zontal convergence with the H.STAT variable resistor and the

V.STAT magnet in the manner given below.

(In this case, the H.STAT variable resistor and the V.STAT

magnet influence each other.)

B

R

B

R

a

b

b

b

a

b

a

b

a

R

G

B

b

B

G

R

b

b

a

a

1

2

3

G

G

B     G     R

R     G     B

H. STAT

V. STAT
Magnet

Center dot

R   G   B

R

G

B

RV702
H. STAT

RV701
SCREEN (G2)

C Board

•

Tilt the V.STAT magnet and adjust the static convergence by

opening or closing the V.STAT magnet.

If the V.STAT magnet is moved in the direction of the a and
b arrows, the red, green, and blue points move as shown

below.