Sony KV-J14KD7 Service Manual ▷ View online
– 17 –
KV-J14KD7/J14KF7
RM-883
3-3. FOCUS ADJUSTMENT
Adjust FOCUS control on the C board (RV703) for the best focus.
b. METHOD OF CANCELLATION FROM SERVICE
MODE
Set the standby condition (Press
POWER
button on the
commander) and then press
POWER
button again, hereupon it
becomes TV mode.
c. METHOD OF WRITE FOR MEMORY
1) Set to Service Mode.
2) Press
1 (UP) and 4 (DOWN) to select an item of
adjustments.
3) Press
MUTING
button and it will indicate WRITE on screen.
4) Press
- button to write into memory.
d. MEMORY WRITE CONFIRMATION METHOD
1) After adjustment, pull out the plug from AC outlet, and then
plug into AC outlet again.
2) Turn the power switch ON and set to Service Mode.
3) Call the adjusted items again, confirm they were adjusted.
Note
Initial DATA
09
RDR
25
WHITE POINT R
0A
GDR
20
WHITE POINT G
0B
BDR
20
WHITE POINT B
Item
number
number
Adjustment
item
item
3-4. ADJUSTMENT WITH COMMANDER
a. AN ITEM OF ADJUSTMENT
SERVICE
MUTING
1 F
DATA
RDR
Adjustment Item
09
Item number
WRITE
1 F
RDR
09
0
Executes the writing
3-5. G2 (SCREEN) AND WHITE BALANCE
ADJUSTMENTS
1. G2 (SCREEN) ADJUSTMENT (RV701)
1) Set the PICTURE and BRIGHTNESS to normal.
2) Put to VIDEO input mode without signals.
3) Connect R, G and B of the C board cathode to the oscilloscope.
4) Adjust G2 (RV701) volume to the value below.
2. WHITE BALANCE ADJUSTMENTS
1) Set to Service Mode.
2) Input an entire white signal.
3) Set the PICTURE to maximum.
4) Select RDR(09) with
1 and 4 , and then set the level to 25
with
3 and 6 .
5) Select GDR(0A) and BDR(0B) with
1 and 4 and adjust the
level with
3 and 6 for the best white balance.
6) Write into the memory by pressing
MUTING
, then
- .
0 V
165
±
2 V DC
– 18 –
KV-J14KD7/J14KF7
RM-883
SECTION 4
SELF DIAGNOSIS FUNCTION
If no acknowledgement is returned from a device which is turned "ON", the device has a problem.
In this case, one of the LED's responding to the problem device will flicker a defined number of times.
Flickering is operated by lighting the LED's for 60ss each time.
The flickering frequency responding to each failed device is shown below.
All the devices are checked one after another from the left of the table.
If an error is found, the responding LED will start flickering.
So, if more than 1 device have failed, only the one on the left side will flicker.
Device
Flickering
Frequency
NONVOLATILE
MEMORY
(IC003)
1
—
—
Y/C JUNGLE
(IC300)
3
—
—
—
—
TONE
CONTROL
(IC201)
6
– 19 –
KV-J14KD7/J14KF7
RM-883
Entering service mode
With the unit on standby
↓
DISPLAY
↓
5
↓
VOL (+)
↓
POWER
The operation sequence puts the unit into service mode.
SECTION 5
CIRCUIT ADJUSTMENTS
5-1. ADJUSTMENTS WITH COMMANDER
Service adjustments are made with the RM-883 that comes with
this unit.
[1], [4]
Raise/lower the service item number
[3], [6]
Raise/lower the data
[MUTING]
Writes
[0]
Executes the writing
[7], [0]
All data becomes the values in memory
[8], [0]
All user control goes to the standard state
[5], [0]
Service data initialization (Be sure not to use
usually.)
[2], [0]
Write 50Hz adjustment data to 60Hz, or
viceversa.
The screen display is :
[1], [4]
Select the adjustment item.
↓
[3], [6]
Raise/lower the data.
↓
[MUTING]
Writes
↓
[0]
Executes the writing.
SERVICE
Mode
08
DATA
RGB
50
Depends on the signals
PAL, SECAM : 50
NTSC : 60
1000
0000
Adjustment item
00
Item number
SELECT
p
PIC MODE
p
SOUND
MODE
VOL
PROGR
RM-883
g
POWER
DISP
REVEAL
MUTING
TV
VIDEO
HOLD
TEXT
A/B
ENLARGE
WIDE/
V-ZOOM
WAKE UP
INDEX
SLEEP
TEXT CLR
+
+
1
2
3
4
6
7
8
9
0
+
p
–
p
5
TV
RM-883
– 20 –
KV-J14KD7/J14KF7
RM-883
5-2. ADJUSTMENT METHOD
Item Number 08
This explanation uses V-SHIFT as an example.
1. Select 08 V-SHIFT with the
[1] and [4] buttons.
2. Raise/lower the data with the
[3] and [6] buttons.
3. Select the optimum state. (The standard is 0F f or PAL
reception.)
4. Write with the
[MUTING] button.
5. Execute the writing with the
[0] button. (The WRITE
display returns to green SERVICE.)
Use the same method for Items Number 00-2F. Use
[1] and [4] to
select the adjustment item, use
[3] and [6] to adjust, write with
[MUTING], then execute the write with [0].
WRITE
WRITE
GREEN
0C
VSF
08
SERVICE
50
50
50
GREEN
0C
VSF
08
Adjusted with “3” and “6” buttons
Written with “MUTING”
Write executed with “0”
GREEN
The WRITE display
will change back to
SERVICE.
0C
VSF
08
Ajust with the
[3]
and
[6]
buttons.
Written with
the
[MUTING]
.
Write executed with
[0]
.
Click on the first or last page to see other KV-J14KD7 service manuals if exist.