DOWNLOAD Sony KV-HZ29N90 Service Manual ↓ Size: 7.9 MB | Pages: 127 in PDF or view online for FREE

– 53 –

The adjusting ranges according to its position selected.

It is adjustable from the selected point to the center.

Left: Left to center

Upper: Upper to center

Upper left: Upper left to center

In case of 1 step inner from each edges: Marker position to center, it cannot be adjusting

  on the outside of the marker.

Landing: Left 11 points, right 11 points
Select R, G or B signal by pressing “6” on the remote commander.
In case of selecting VIDEO without input, a single color is
displayed.

Convergence: Move the marker from the center to outer spirally.
Only the center data is within +-15.

Fine mode

Landing

Convergence

Fine mode

Adjustable at each point.

Move DY.

Purity

All red or blue

– 54 –

1. Receive the signal.

TV terminal (sub) : Color-bar (white-75%, No

   setup)

VIDEO terminal (main)  : Color-bar (white-75%, No

   setup)

2. VIDEO MODE

: AV Pro

PICTURE

: maximum

COLOR

: minimum

RGB Signal

: off

3. Set to P & P mode, and set to service mode.

4. Set the service data.

Category

Reg. No & Name

Standards

MCP

2 RON

1

3 GON

0

4 BON

0

7 YLMT

1

PIC

0 PIC

100

1 COL

0

5 PIOF

0

 5. Connect an oscilloscope between the check point and ground.

Check points

: CN9001 pin 

1 (R-DRV)

(C Board)

6. Adjust the item as shown below.

Category

Reg. No & Name

LEFT

CCPM

1

YLEV

RIGHT

YCTS

0

YLEV

7. Write the data into memory.

    

  MUTE     n    

  

0

<KV-HZ34M65/M85/M90 models>

        

  n  

    

0

<KV-HZ29N90/34N90 models>

1. Receive the signal.

TV terminal (sub) : Color-bar (white-75%, No

   setup)

VIDEO terminal (main) : Color-bar (white-75%, No

   setup)

2. VIDEO MODE

: AV Pro

PICTURE

: maximum

COLOR

: center

RGB Signal

: on

3. Set to P & P mode, set to service mode.
4. Set the service data.

Category

Reg. No & Name

Standards

MCP

2 RON

1

3 GON

1

4 BON

1

7 YLMT

1

PIC

0 PIC

60

1 COL

50

5. Connect an oscilloscope between pin  

5 (B-DRV)  of CN9001

(C board) connecter and ground.

6. Adjust the item as shown below to have VB1      VB4 and

VB2    VB3 in the waveform levels.

Category

Reg. No & Name

LEFT

CCPM

2

CLEV

3

SHUE

RIGHT

YCTS

1

CLEV

4

SHUE

7. Write the data into memory.

   

   MUTE     n      0

<KV-HZ34M65/M85/M90 models>

      n      0

<KV-HZ29N90/34N90 models>

VB1      VB2     VB3     VB4

<

=

<

=

Fine mode
Adjustable at each point.

White

GND

VR1

VR1-VR2=VR=1.95   0.07Vp-p

VR2

sync tip

– 55 –

(1).VIDEO MODE : AV PRO

PICTURE : Maximum
COLOR

: Minimum

Color Temp.: High
DRC-MF

: Progressive

(2). Receive the all white signal and set to full mode screen and

to the service mode.

(3). Minimize the cut-offs and make drives normal in the follow-

ing items.

Category

Reg. No & Name

COLR

3 GDRV
4 BDRV
6 GCUT
7 BCUT

(4). Adjust with the cut-offs and the drives mutually the white

balance becomes best in the mode the picture is maximum or
minimum.

Focus adjustment should be completed before W/B adjustment.

(1) Receive digital monoscope pattern.
(2) Set DRC-MF to “Progressive” and PICTURE to “Standard”.
(3) Adjust FOCUS VR so that the center of the screen becomes

justfocus.

(4) Change the receiving signal to white pattern and blue back.
(5) Confirm MAGENTA RING should not be over the limit sam-

ple. In case MAGENTA RING is over the limit sample,
adjust FOCUS VR to take tracking of MAGENTA RING and
FOCUS.

FOCUS

SCREEN G2

– 56 –

When replacing the f

ollowing components marked with 

 on the

schematic diagram always check HV regulation, and if neces-
sary re-adjust.

: RV8002
: IC8004, IC8005,

R8014, R8015, R8017
PH8003
T8001 (FBT)
D board

1. Connect a HV static voltmeter to the unconnected plug of the high-

voltage block.

2. Power on the set.

3. Receive the dot signal.

4. Set PIC MIN/BRT MIN.

5. Confirm that the static voltmeter reading is 31.5 

± 0.3kVDC.

6. If not, adjust with RV8002 to the specified value.

When replacing the following components marked with 

 on

the schematic diagram always check hold-down voltage.

: RV8002
: D8014

IC8001
R8016, R8019, R8046, R8052, R8072,
R8078, R8079, R8165
T8001 (FBT)
D board

1. Connect a HV static voltmeter to the unconnected plug of the high-

voltage block.

2. Power on the set.

3. Receive the dot signal.

4. Set PIC MIN/BRT MIN.

5. The set turns off (the protector circuit activates) at the 36.6kVDC

or less reading on the static voltmeter.

6. After that, adjust the item 5-2 (Return to 31.5kVDC).

1. Supply 242 

±   VAC (Except Taiwan model) or 121 ±  VAC

(Taiwan model) to variable autotransformer.

2. Receive dot signal pattern and set the PICTURE and

BRIGHTNESS settings to their minimum.

3. Confirm the voltage between the both sides of C6512 on D

board  is 137.0 V dc.

When replacing the following components marked with / on the

schematic diagram, always check IK protector circuit.

:

D8004
IC8001
Q8007
R8027, R8030, R8035,R8037
R8038, R8039, R8040, R8041, R8043,
D board

1. Unsolder T8001 (FBT) Pin 1 and connect a DC current meter

between Pin 1 and the pattern.

2. Remove R0494 (MG MOUNT).
3. Feed the all white signal, increase the picture and brightness

slowly and check the hold-down works when the reading on
the DC current meter is 2670uA.

4. Turn power off.
5. Remove the DC current meter and set R0494 solder the

unsolder portions.

2

0

2

0