DOWNLOAD Sony KV-HX32M31 (serv.man2) Service Manual ↓ Size: 6.71 MB | Pages: 125 in PDF or view online for FREE

– 49 –

1. The Red and Blue magnets should be equally far from the

horizontal center line.

2. Do not separate the Red and Blue magnets too far. (Less than

8 mm)

4

 BMC (Hexapole) Magnet.

If the red, green and blue dots are not balanced or aligned,
then use the BMC magnet to adjust in the manner described
below.

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

1. Receive the cross-hatch signal and adjust [PICTURE] to

[MIN] and [BRIGHTNESS] to [STANDARD] .

2.  Adjust the Y separation axis correction magnet on the neck

assembly so that the horizontal lines at the top and bottom of
the screen are straight.

1. The Red and Blue magnets should be equally far from the

horizontal center line.

2. Do not separate the Red and Blue magnets too far. (Less than

8 mm)

5

 Y separation axis correction magnet adjustment.

Blue

Red

VM board

Blue

Red

VM board

Neck assy

Neck assy

(2) Dynamic Convergence Adjustment
Preparation:
•

Before starting this adjustment, adjust the horizontal static
convergence and the vertical static convergence

•

Set the PICTURE and BRIGHTNESS to normal.

1

 Receive the dot/hatch pattern signal and adjust picture qual-

ity by the menu.

2

 Correct horizontal mis-convergence of red and blue of both

sides on the X axis.
When red is outside insert BMC magnet to right side (THL+)
views from DY neck. And when blue is outside, insert it to
left side (THL–) and take both sides.

R

(B)

B

(R)

B

(R)

R

(B)

To able to become balance of XCV on the X axis well.

Correct the vertical mis-convergence of red and blue of verti-
cally sides on the Y axis.

Adjust horizontal mis-convergence of red and blue of verti-
cally sides on the Y axis. Mentioned above steps 2 to 4 are
adjusting respectively perform minuteness tracking.

XCV

C board

RV9001

TLV1

YCH

TLV2

BMC magnet

W board

– 50 –

Focus adjustment should be completed before W/B adjustment.

(1) Receive digital monoscope pattern.
(2) Set DRC-MF to “Progressive” and PICTURE to “Standard”.
(3) Adjust FOCUS VR so that the center of the screen becomes

justfocus.

1) Set to zoom mode and the PICTURE and BRIGHTNESS to

normal and to the service mode.

2) In put monoscope signal.
3) Set the service data.  CXA2150P-210: ABLK10
4) Connect R, G and B of the C board cathode to the oscillo-

scope.

5) Adjust BRIGHTNESS to obtain the cathode voltage to the

value below.

6) Whilst watching the picture, adjust the screen VR located on

the flyback transformer to the point just before the flyback
return lines disappear (to the point before cut-off)

0 V

170V – 0.5 (VDC)

FOCUS

SCREEN G2

(3) Screen-corner Convergence

b

a

c

d

a-d : screen-corner
        misconvergence

Fix a Permalloy assy corresponding to the misconverged
areas.

a

b

c

d

Permalloy assembly

– 51 –

(1) Receive dot/hatch pattern.
(2) Turn FOCUS VR fully counter-clockwise.
(3) Confirm the dot shape at the screen center.
(4) Resume FOCUS VR.

In case of turning NECK ASSY, loosen the screw 3 turns. Do not
move the position.

 OK

 Turn NECK ASSY clockwise.

 Turn NECK ASSY counter clockwise.

Note: In this adjustment use the monoscope signal.

    Adjust in the service mode “DEF1” and “DEF2”.

0 (VPOS)-DEF1

1 (VSIZ)-DEF1

2 (VLIN)-DEF1

3 (VSCO)-DEF1

2 (HSIZ)-DEF2

1 (HPOS)-DEF2

5 (PIN)-DEF2

6 (UCP)-DEF2

7 (LCP)-DEF2

8 (PPHA)-DEF2

9 (VANG)-DEF2

11 (VBOW)-DEF2

11 (SCRL)-DEF1

12 (UVLN)-DEF1

13 (LVLN)-DEF1

1. Receive the signal.

TV terminal (sub) : Color-bar (white-75%, No

   setup)

VIDEO terminal (main)  : Color-bar (white-75%, No

   setup)

2. VIDEO MODE

: AV Pro

PICTURE

: maximum

COLOR

: minimum

RGB Signal

: off

3. Set to P & P mode, and set to service mode.

4. Set the service data.

Category

Reg. No & Name

Standards

MCP

2 RON

1

3 GON

0

4 BON

0

7 YLMT

1

PIC

0 PIC

100

1 COL

0

5 PIOF

0

 5. Connect an oscilloscope between the check point and ground.

Check points

: CN9001 pin 1 (R-DRV)

(C Board)

6. Adjust the item as shown below.

Category

Reg. No & Name

LEFT

CCPM

1

YLEV

RIGHT

YCTS

0

YLEV

7. Write the data into memory.

MUTE     

n      12

White

GND

VR1

VR1-VR2=VR=1.95   0.07Vp-p

VR2

Sync tip

– 52 –

(1).VIDEO MODE : AV PRO

PICTURE : Maximum
COLOR

: Minimum

Color Temp.: High
DRC-MF

: Progressive

(2). Receive the all white signal and set to full mode screen and

to the service mode.

(3). Minimize the cut-offs and make drives normal in the follow-

ing items.

Category

Reg. No & Name

COLR

3 GDRV
4 BDRV
6 GCUT
7 BCUT

(4). Adjust with the cut-offs and the drives mutually the white

balance becomes best in the mode the picture is maximum or
minimum.

Focus adjustment should be completed before W/B adjustment.

(1) Receive digital monoscope pattern.
(2) Set DRC-MF to “Progressive” and PICTURE to “Standard”.
(3) Adjust FOCUS VR so that the center of the screen becomes

justfocus.

(4) Change the receiving signal to white pattern and blue back.
(5) Confirm MAGENTA RING should not be over the limit sam-

ple. In case MAGENTA RING is over the limit sample,
adjust FOCUS VR to take tracking of MAGENTA RING and
FOCUS.

FOCUS

SCREEN G2

1. Receive the signal.

TV terminal (sub) : Color-bar (white-75%, No

   setup)

VIDEO terminal (main) : Color-bar (white-75%, No

   setup)

2. VIDEO MODE

: AV Pro

PICTURE

: maximum

COLOR

: center

RGB Signal

: on

3. Set to P & P mode, set to service mode.
4. Set the service data.

Category

Reg. No & Name

Standards

MCP

2 RON

1

3 GON

1

4 BON

1

7 YLMT

1

PIC

0 PIC

60

1 COL

50

5. Connect an oscilloscope between pin  5 (B-DRV)  of CN9001

(C board) connecter and ground.

6. Adjust the item as shown below to have VB1     VB4 and

VB2    VB3 in the waveform levels.

Category

Reg. No & Name

LEFT

CCPM

2

CLEV

3

SHUE

RIGHT

YCTS

1

CLEV

4

SHUF

7. Write the data into memory.

      MUTE     

n      12

VB1      VB2     VB3     VB4

<

=

<

=