DOWNLOAD Sony KV-HW21M50 Service Manual ↓ Size: 40.3 MB | Pages: 127 in PDF or view online for FREE

– 9 –

2 Rear cover

1 3D Speaker box assy

(KV-HW21M63/M83 only)

2

 Rear cover

1

Eight screws
(BVTP 4 

× 16)

1

Four screws

(BVTP 4 

× 16)

2

 

Terminal 

     bracket

3

 

One screw

      (+BVTP 4x16)

1

 

One screw

      (+BVTP 3x16) 

– 10 –

1

 

Two screws

     (BVTP 3x12)
     (KV-HW21M63/M83 only) 

• Pls make sure the TV set is not in standing position before removing necessary CRT support located on bottom

right and left.

1) Place the TV set with the CRT face down on a cushion jig.
2) Remove the rear cover.
3) Unplug all under connecting leads from the Deflection Yoke, Degaussing Coil and CRT grounding strap.

8

 Degaussing Coil

2

 C Board Removal

5

 Chassis Assy Removal

6

 Support, CRT(2) Removal

3

 Loosen the Neck Assembly

fixing screw and removal

7

 Holder, DGC(2) 

Removal

9

 DGC(2) Removal

1

 Spring Tension (2)

Removal

0

 Nut locking, CRT (4)

4

 Loosen the Deflection Yoke

fixing screw and remove

A Board

– 11 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1

Turn up one side of the rubber cap in the direction
indicated by the arrow A.

2

Using a thumb pull up the rubber cap firmly in the di-
rection indicated by the arrow B.

3

turning up the rubber cap and pulling it up in the
direction of the arrow C.

• HOW TO HANDLE AN ANODE-CAP

1

2

3

anode button

a

a

b

b

c

– 12 –

• The following adjustments should be made when a

complete realignment is required or a new picture
tube is installed.

Set the controls as follows unless otherwise noted:
VIDEO model .....................................................  Standard
PICTURE control ..................................................  normal
BRIGHTNESS control ..........................................  normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. Screen(G2)
5. White Balance
Note : Test Equipment Required.

1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter
5. Oscilloscope

Purity control

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

Preparation :
• In order to reduce the influence of geomagnetism on

the set's picture tube, face it east or west.

• Switch on the set's power and degauss with the

degausser.

Picture Mode: DYNAMIC
1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Set the pattern generator raster signal to a green

raster.

3. Move the deflection yoke to the rear and adjust with

purity control so that the green is at the center and
the blue and the red take up equally sized areas on
each side. (See Figures 2-1 through 2-4.)

4. Move the deflection yoke forward and adjust so that

the entire screen is green. (See Figure 2-1.)

5. Switch the raster signal to blue then to red and verify

the condition.

6. When the position of the deflection yoke has been

decided fasten the deflection yoke with the screws
and DY spacers.

7. If the beam does not land correctly in all the corners,

use a magnet to adjust it. (See Figure 2-4.)

}

......................................................................................................................................................................................................................

normal