DOWNLOAD Sony KV-HW212M60 Service Manual ↓ Size: 3.9 MB | Pages: 67 in PDF or view online for FREE

– 32 –

4. Rasie/lower data using the 

3

 and 

6

 buttons adjust

the following items:-

GEOM :

000

HPOS

Horizontal Shift (HS)

001

HPAR

Horizontal Parallelogram

002

HBOW

Horizontal Bow

003

VLIN

Vertical Linearity

004

VSCR

Vertical Scroll

005

HSIZ

EW Width (EW)

006

EWPW

EW Parabola/Width (PW)

007

UCOP

EW Upper Corner Parabola

008

LCOP

EW Lower Corner Parabola

009

EWTZ

EW Trapezium

010

VSLP

Vertical Slope (VS)

011

VSIZ

Vertical Amplitude

012

SCOR

S-Correction (SC)

013

VPOS

Vertical Shift (VSH)

014

HBL

RGB Blanking Mode

015

WBF

Timing of Wide Blanking (WBF)

016

WBR

Timing of Wide Blanking (WBR)

017

SBL

Service Blanking

018

COPY

Copy the GEO data to all
50/60Hz NVM area

5. Write into memory by pressing [MUTING] then 

-

 on

the remote commander.

1. Input SPCB signal.
2. Adjust condition change to WIDE MODE : ON
3. Copy (Item from normal mode 50Hz) all Normal

Mode adjusted data.

1. Input 525/60Hz signal.
2. They can copy 50Hz first.

("COPY" under GEOM is set to 

1

, then [MUTE] + 

-

)

3. Using the 

1

 and 

4

 button, select category GEOM

(Service Mode).

4. Raise/lower data using the 

3

 and 

6

 buttons to

obtain optimum image.

GEOM :

000

HPOS

Horizontal Shift (HS)

001

HPAR

Horizontal Parallelogram

002

HBOW

Horizontal Bow

003

VLIN

Vertical Linearity

004

VSCR

Vertical Scroll

005

HSIZ

EW Width (EW)

006

EWPW

EW Parabola/Width (PW)

007

UCOP

EW Upper Corner Parabola

008

LCOP

EW Lower Corner Parabola

009

EWTZ

EW Trapezium

010

VSLP

Vertical Slope (VS)

011

VSIZ

Vertical Amplitude

012

SCOR

S-Correction (SC)

013

VPOS

Vertical Shift (VSH)

014

HBL

RGB Blanking Mode

015

WBF

Timing of Wide Blanking (WBF)

016

WBR

Timing of Wide Blanking (WBR)

017

SBL

Service Blanking

018

COPY

Copy the GEO data to all
50/60Hz NVM area

1. Input mono scope signal.
2. Adjust condition change to WIDE MODE : ON
3. "COPY" is set to 

1

, then [MUTE] + 

-

1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the HPOS item with 

1

 and 

4

.

4. Adjust the value of HPOS with 

3

 and 

6

 for the best

vertical center.

5. Press [MUTING] then 

-

 to save into the memory.

1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HSIZ with 

1

 and 

4

.

4. Adjust with 

3

 and 

6

 for the best horizontal size.

5. Press [MUTING] then 

-

 to save into the memory.

1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with 

1

 and 

4

.

4. Adjust value of VPOS with 

3

 and 

6

 for the best

vertical center.

5. Press [MUTING] then 

-

 to save into the memory.

1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VPOS item with 

1

 and 

4

.

4. Adjust value of VPOS with 

3

 and 

6

 for the best

vertical center.

5. Press [MUTING] then 

-

 to save into the memory.

– 33 –

1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select VLIN, SCOR, EWPW, and EWTZ with

1

 and 

4

.

4. Adjust with 

3

 and 

6

 for the best horizontal size.

5. Press [MUTING] then 

-

 to save into the memory.

1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HPAR, HBOW, UCOP, and LCOP with

1

 and 

4

.

4. Adjust with 

3

 and 

6

 for the best picture.

5. Press [MUTING] then 

-

 to save into the memory.

UPPER PIN (UCOP)

LOW PIN (LCOP)

V ANGLE (HPAR)

V BOW (HBOW)

EW TRAPEZIUM (EWTZ)

EW PARABOLA/WIDTH (EWPW)

S CORRECTION (SCOR)

V LINEARITY (VLIN)

– 34 –

VIF SAW

SIF SAW

MAIN

Power

Supply

RF AMP Tuner

TEQE2X904B

AGCin

12C

TV

L(Mono)

Video

L(Mono)

CV/YC

L(Mono)

R

CV/YC

L(Mono)

R

R

R

G/Y

B/P

B

R/P

R

L

R

Fbl(RGBin)

24.576MHz

DVD/RGB

AV3

AV2

AV1

MON OUT

Audio Amp

Buffer

TV 

out

Radio

BPF

Mon

out

AV1

in

AV2

in

CV/YC

L(Mono)

AV3

IN

RGB/

DVD

in

5V

30V

IF

24-5.VIFIN1~2

29~30.SIF1~2

115.DGC RELAY 

114.STBY SW

STBY

3.3V

AC in ~

110-220V

CISPR/

PFC

3.3V

RESET

3.3V

5V

8V

3.3/5V

Relay

8V

AUDIO VCC

HV

DGC

+/-15V

Hout

FBT

L

2ch

Audio Amp

ATT

VAR

NVM

Pin out

H-drive

H-out

Rot. cct

V-out

VM

RGB Amp

feedback

10W

R

10W

L,R

I

HP

mute

EHT, ABL

Hp

1k

EW, Hd

L, R

V+, V-

RGB

+B

On/Off

stdby

Device 12C

12C

SIRCS

Key buttons

PLL

I/O Port

I/O Port

VIF & SIF

POWER

Color

Decoder

YUV

Processor

Jungle

RGB

DAC

Stereo,

DAP

A
D
C

ONE CHIP

Micro

Text

CC & V-chip

11.Xtalout

10.Xtalin

74~76.YUVout

70-72.VUYIN in

119.KEY

116.DI-JP/MODE1-EU

103.DI-JP/MODE2-EU/

MON SW

-MONO

126.AGC-MUTE

98, 99. SCL1,SDA1

108, 109.  SCL0,SDA0 

102.BINT

122~3.RED~GREEN LED

77.SCART FBL

78~80.RGB3
34,35 InLs,R5 

51.CY/Y4
52.C2
49-50 InL,R4

120.P3.3(S2)

31.AGCout

33.AVL/2SIF 120.S2

44.Intco-IF

43.IFVO

62,63.HPL, R

48.MON-OUT

36,37.OutL, R

111.S1/VC(GA)

85~87

RGBout

84.lk

65.VM

23. VD+

22. VD-

112.ROT CTRL

113.ROT SW

21.EWD

67.Hout

66.AFC 

32.EHTO

83.ABL

60,61

LSL,R

106.AUDIO MUTE

105.AUDIO STANDBY

58.CVB51/Y1
59,C1 
56, 57InL1,InR1
55.CV/Y2
53,54.InL,R2
70 CX

B-INT

LED

+B line

30V

R

LNA cct

– 35 –

Note:
•

All capacitors are in 

µ

F unless otherwise noted.

•

All electrolytic capacitors are rated at 50V unless otherwise
noted.

•

All resistors are in ohms.
k

Ω

 = 1000

Ω

, M

Ω

 = 1000k

Ω

•

Indication of resistance which does not have rating
electrical power is as follows.

Pitch: 5 mm
Rating electrical power 1/4W (CHIP: 1/10W)

•

: nonflammable resistor.

•

: fusible resistor

•

¢

: internal component.

•

: panel designation or adjustment for repair.

•

All variable and adjustable resistors have characteristic
curve B unless otherwise noted.

Ω

✽

k

Reference information
RESISTOR

: RN

METAL FILM

: RC

SOLID

: FPRD

NONFLAMMABLE CARBON

: FUSE

NONFLAMMABLE FUSIBLE

: RS

NONFLAMMABLE METAL
OXIDE

: RB

NONFLAMMABLE CEMENT

: RW

NONFLAMMABLE
WIREWOUND

: 

✽

ADJUSTMENT RESISTOR

COIL

: LF-8L

MICRO INDUCTOR

CAPACITOR

: TA

TANTALUM

: PS

STYROL

: PP

POLYPROPYLENE

: PT

MYLAR

: MPS

METALIZED POLYESTER

: MPP

METALIZED POLYPROPYLENE

: ALB

BIPOLAR

: ALT

HIGH TEMPERATURE

: ALR

HIGH RIPPLE

!

Note: “A” board schematic diagram is divided into 7 blocks.

Each block is named by its function and block
“number”. eg: Processor (Block 001)
Joint connection between boards can be identified
using the block number followed by the grid's guide.
eg: -<PWR-OFF MUTE
002 : 4E
Meaning: Block 001 joint "PWR-OFF MUTE" is
connected to Block 002 joint "PWR-OFF MUTE"
located at grid 4E

A Board

C Board

J Board (KV-HW212M83/M83/H)