DOWNLOAD Sony KV-HV212M50 Service Manual ↓ Size: 10.98 MB | Pages: 67 in PDF or view online for FREE

– 12 –

1) Dress DY Conn along Conn Assy, 5P (200V) as shown. 

2) Dress DY Conn and Conn Assy, 5P (200V) with Purse Lock Ø5.

     Note : Keep DY Conn & Conn Assy, 5P away from FBT area by a distance of 10mm or more.

DY Conn goes underneath of 
Earth Assy, Coating and Conn
Assy, 5P (200V)

DY Conn goes above Conn Assy, 5P (200V).

DY Conn

Conn Assy, 5P (200V)

Earth Assy, Coating

Purse Lock Ø5

DY Conn

Conn Assy, 5P

 (200V)

Use heat sink height to
estimate purse lock location

Purse Lock Ø5

≥ 10mm

Dress DY Conn and Conn Assy, 5P
(200V) with Purse Lock Ø5.

All wires must be kept away from
FBT area by a distance of 10mm or
more

Dress Earth Assy, Coating, Lead Assy, G2 & Focus with purse lock Purse Lock Ø5. as shown

Note : Keep Lead Assy, G2 away from HV Cable (min 1mm/kV)
          Ensure Lead Assy, G2 is kept away from heat sinks

Purse lock dia.5

FBT 

(G2)

CN704

(C)

ECA

FBT 

(Focus) 

CRT 

SOCKET

CN705

(C)

Lead Assy, Focus

Lead Assy, G2

Keep Lead Assy, G2

away from Heat Sink.

Keep Lead Assy, G2
away from HV Cable

(at least 1mm/kV)

Dress tight at the portion to avoid
wire touches rear cover .

Rear view of Lead Assy, Focus & G2, connected
from FBT A brd to C brd.

Lead Assy, G2

Lead Assy, Focus

Conn. Assy, 5P (200v)

Earth Assy, Coating

TVSR requirement :
1. Spacing between HV cable and other conductive part’s surface is 1mm/kV or more.
2. Spacing between HV cable's and enclosure with ventilation or the edge where
 

terminal bracket and rear cover meet: 10 mm or more.

Purse Lock, dia.5

Use this as a reference to dress
ECA, Lead Assy, Focus & G2.

Make sure DY Conn is on the right
side of Earth Assy, Coating

– 13 –

Dress Conn Assy, 7P, UL Wire (1-923-000-81), Lead Assy, Earth, 

Dress Conn Assy, 7P, UL Wire (1-923-000-81), Lead Assy, Earth, 

Conn Assy, 3P(1-900-703-83), Rotational Coil Conn with purse lock, Ø9 as shown.

and Rotational Coil Conn with purse lock, Ø5 as shown.

Note : Keep Lead Assy, Earth away from heat sinks. 

Note : Keep Lead Assy, Earth away from heat sinks. 

Purse Lock Ø9

Lead Assy,

Earth

Conn Assy, 7P

UL Wire (1-923-000-81)

Conn Assy,

3P

Rotational Coil

Conn

Rotation Coil

DY

90

Purse Lock Ø5

Keep Lead Assy, Earth away
from heat sinks

Conn Assy, 7P

Rotational
Coil Conn

Lead Assy, Earth

A:  Conn Assy, 7P
B:  Lead Assy, Earth
C:  UL Wire (1-923-000-81)
D: Rotational Coil Conn
E: Conn Assy, 3P (woofer)

A      B    C   D  E

Purse Lock Ø9

A:  Conn Assy, 7P
B:  Lead Assy, Earth
C:  UL Wire (1-923-000-81)
D: Rotational Coil Conn

A    B     C    D 

Purse Lock Ø5

1) Dress HV cap assy with HV Holder as shown

     Note: Make sure the specified position is being followed.

2) Dress HV holder at DGC with purse lock, Ø9 as shown

3) Using Yellow line (CRT Carbon line) as a reference to dress purse lock, Ø9.

Ensure HV Holder is beside
DGC to keep further distance 
from HV Cable

distance > 1mm/kV

distance < 1mm/kV

180 ± 5 mm

HV Cable Holder

Place purse lock Ø9 after the exit of DGC Conn from DGC

DGC

Purse Lock Ø9

Black tape

DGC Conn outlet

Gate (2 positions)

of HV holder

Dress HV Cable at inner ring

45º

Min. distance = 1mm/kV

Min. distance = 1mm/kV

Min. distance =

0.5mm/kV

CRT Carbon

Area

TVSR requirement:
1. Spacing between HV cable and other conductive part’s surface is 1mm/kV or more.
2. Spacing between HV cable's and enclosure with ventilation or the edge where
  terminal bracket and rear cover meet: 10 mm or more.
3. Spacing between edge of anode cap and conductive parts is 0.5mm/kV or more

Keep wires away

from heat sinks

UL Wire (1-923-000-81)

Wire from

Rotation Coil

– 14 –

PWB Bracket hook

Dress AC Power Cord at PWB Bracket hook as shown.

AC Power Cord

Terminal Bracket

AC Cord Holder

Dress AC Cord Holder at the terminal bracket.

– 15 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:

Picture control ......................................................... NORMAL
Brightness control ................................................... NORMAL

Perform the adjustments in order as follows:
1. Beam Landing
2. Convergence
3. Focus
4. G2 (SCREEN)
5. White Balance

Note: Test Equipment Required
1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter

•

Feed in the white pattern signal.

•

Before starting, degauss the entire screen with the
degausser.

•

In order to reduce the geomagnetism on the set's
picture tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loosen the deflection yoke mounting screw, and set the

purity control to the center as shown below.

3. Set the raster signal of the pattern generator to green.
4. Move the deflection yoke (DY) backward and adjust the

purity control so that green is in the center and blue and
red are at the sides evenly.

5. Then move the DY forward and adjust so that the entire

screen becomes green.

6. Now switch over raster signal to red then blue and

confirm the condition.

...................................................................................................................................................................................................................... ...........

5. Oscilloscope
6. Landing Checker
7. XCV Adjuster

Purity control

Red

Blue

Green

7. When the position of the DY is determined, tighten it

with the DY mounting screw.

8. If the beam does not land correctly in all corners of the

screen, use magnet disc to correct it.

•

Before starting, perform FOCUS adjustment.

•

Picture mode STANDARD.

•

Receive dot/cross hatch pattern.

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

Center dot

R    G    B

R

G

B

4 pole magnet

C/CV Board