Sony KV-G14DK2 Service Manual ▷ View online
– 21 –
– 21 –
KV-G14DK2/G14P2/G14P2S
KV-G14Q2/G14Q2S
RM-869
Option Note
Item No. 13 VPX
Item
HCO
EVG
SBL
PRD
–
–
–
VID
Initial data
0
0
0
0
0
0
0
0
HCO
EHT Tracking Mode
1 = on V and E–W.
0 = only on V
EVG
Enable Vertical Guard
1 = enable.
0 = disable
SBL
Service Blanking
1 = active.
0 = inactive
PRD
Over-voltage Protection Detection
1 = enable.
0 = disable
VID
Video Ident Mode
1 = not for ø1-loop
0 = for ø1-loop
Item No. 3E OP0
Item
No TOP
AV input
AVMUT
B/G
I
D/K
M
Initial data
1
1
0
0
1
0
0
0
AV Input
0
0 no AV input model
0
1 1 AV input model
1
0 2 AV input model
1
1 2 AV input and RGB input model
No TOP (for teletext model)
1 = only FLOF available.
0 = both FLOF and TOP available
AV MUT
1 = AV multi is always muted if no signal input. 0 = not muted always
Other optional bits are effective if set to 1.
Item No. 3F OP1
Item
No NICAM
–
HDEV
1 V-Curve
XTAL SEL
SECAM
2nd Lang.
Initial data
0
0
0
0
1
1
0
1
XTAL SEL 0
0 only 4.43 XTAL
0
1 only 3.58 XTAL
1
0 (not used)
1
1 both 4.43 and 3.58 XTAL
1 V-Curve (for monaural model)
1 = using common volume curve for every mode and every TV system
0 = another volume curve available for video mode and M system
0 = another volume curve available for video mode and M system
HDEV
1 = High Deviation Mode switch available.
0 = not available
Other optional bits are effevctive if set to 1.
Item No. 40 OP2
Item
–
–
No. Bal
TV Out
Hotel
VM
D.B.F.B.
Thai Bil.
Initial data
0
0
0
0
0
0
0
0
No Bal. (for AV stereo model)
1 = no balance in analog select items.
0 = balance included
Other optional bits are effective if set to 1.
Hotel TV mode should be switched with remote commander from STBY condition as below.
Hotel TV mode should be switched with remote commander from STBY condition as below.
Hotel TV on : push “display”. “8”. “vol +” and “power” sequentially
Hotel TV off : push “display”. “8”. “vol –” and “power” sequentially
Hotel TV off : push “display”. “8”. “vol –” and “power” sequentially
– 22 –
– 22 –
KV-G14DK2/G14P2/G14P2S
KV-G14Q2/G14Q2S
RM-869
4-4. PICTURE DISTORTION ADJUSTMENT
Item Number 00 – 08
4-3. A BOARD ADJUSTMENT AFTER IC003
(MEMORY) REPLACEMENT
1. Enter to Service Mode.
2. Press commander buttons 5 and - (Data Initialize), and 2
and - (Data Copy) to initialize the data.
3. Call each item number, and check if the respective screen shows
the normal picture.
In case some items are not well-adjusted, give them fine
adjustment.
Write the data per each item number (
MUTING
+ -).
4. Select item numbers “3E” (OP0), “3F” (OP1) and “40” (OP2)
and respectively set the bit per model with command buttons
3 and 6.
3 and 6.
5. Press commander buttons 8 and - (Test Normal) to return
to the data that was set on the shipment from the factory.
(= Cancel Service Mode.)
00 HSF (H SHIFT)
01 HSZ (H SIZE)
02 PAP (PIN AMPLITUDE)
03 CNP (CORNER PIN)
04 TLT (TILT)
05 VSL (V SLOPE)
06 VAP (V AMPLITUDE)
07 SCR (S CORRECTION)
08 VSF (V SHIFT)
Click on the first or last page to see other KV-G14DK2 service manuals if exist.