DOWNLOAD Sony KV-DX29K90B Service Manual ↓ Size: 9.27 MB | Pages: 111 in PDF or view online for FREE

– 45 –

No.

Name

Standards

0

PD

*1

1

2

MODL

*2

Standards *1

UV

Video 1

Video 2

Video 3

0

PD

1111

Video 4

D Component 1

D Component 2

AV Multi RGB

AV Multi YUV

0

PD

11111

Standards *2

X

No.

X

No.

X

2

MODL

03140

No.

Name

Remarks

Standards

Standards

Standards

No.

Name

No.

Name

No.

Name

Standards

0

ASHT

1

1

EDFL

0

2

RSVP

1

3

DLY1

24

4

DLY2

20

5

DLY3

7

6

DLY4

0

7

BLK1

20

8

BLK2

40

9

BLK3

20

10

AGCH

3

11

AGCL

14

12

AFTH

149

13

AFTL

87

14

AFDL

8

15

GRDL

0

16

RSGR

0

17

TUON

1

18

NPON

0

19

DHMU

0

20

PCMX

53

21

BRMX

47

22

AVMF

9

23

BSSV

1

24

BTUO

10

25

BDLY

2

26

BTBT

0

27

NBRT

21

28

XEOF

0

29

LBER

20

Remarks

– 46 –

•

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

•

These adjustments should be performed with rated power
supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise

noted:

PICTURE control ........................................................... normal
BRIGHTNESS control................................................... normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note : Test Equipment Required.

1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope

...................................................................................................................................................................

Preparation :
•

In order to reduce the influence of geomagnetism on the set’s
picture tube, face it east or west.

•

Switch on the set’s power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig4-1.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the pu-

rity control so that the green is at the center and the blue and
the red take up equally sized areas on each side.
(See Figures 4-1 through 4-3.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 4-2.)

6. Switch the raster signal to blue, then to green and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.
(See Figure 4-4.)

normal

}

Neck assy

G2

G1

G3

Behind the G2 edge

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

– 47 –

Preparation :
•

Before starting this adjustment, adjust the focus, horizontal
size and vertical size.

•

Set the Picture Mode to “STANDARD”.

•

Cross hatch / Dot pattern.

1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue dots are on top of each other at the center
of the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the

red, green and blue dots are on top of each other at the center
of the screen.

3. If the H.STAT variable resistor cannot bring the red, green

and blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjust-
ments while tracking.)

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV9001

H. STAT

Y magnet

C Board

BMC (Hexapole)

1

V.   STAT

2

H. STAT VR

R

R

G

G

B

B

a

a

b

b

b

R

R

G

G

B

B

a

b

3

R

R

G

G

B

B

a

a

b

b

b

V.STAT

Purity

BMC (hexapole)

– 48 –

1. Receive the cross-hatch signal and adjust [PICTURE] to

[MIN] and [BRIGHTNESS] to [STANDARD] .

2.  Adjust the Y separation axis correction magnet on the neck

assembly so that the horizontal lines at the top and bottom of
the screen are straight.

1. The Red and Blue magnets should be equally far from the

horizontal center line.

2. Do not separate the Red and Blue magnets too far. (Less than

8 mm)

(2) Dynamic Convergence Adjustment
Preparation:
•

Before starting this adjustment, adjust the horizontal static
convergence and the vertical static convergence

•

Set the PICTURE and BRIGHTNESS to normal.

1

 Receive the dot/hatch pattern signal and adjust picture qual-

ity by the menu.

2

 Correct horizontal mis-convergence of red and blue of both

sides on the X axis.
When red is outside insert BMC magnet to right side (THL+)
views from DY neck. And when blue is outside, insert it to
left side (THL–) and take both sides.

4

 BMC (Hexapole) Magnet.

If the red, green and blue dots are not balanced or aligned,
then use the BMC magnet to adjust in the manner described
below.

5

 Y separation axis correction magnet adjustment.

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

Blue

Red

VM board

Blue

Red

VM board

Neck assy

Neck assy

R

(B)

B

(R)

B

(R)

R

(B)

To able to become balance of XCV on the X axis well.

Correct the vertical mis-convergence of red and blue of verti-
cally sides on the Y axis.

Adjust horizontal mis-convergence of red and blue of verti-
cally sides on the Y axis. Mentioned above steps 2 to 4 are
adjusting respectively perform minuteness tracking.

XCV

C1 board

BMC magnet

RV9001

V board

TLV1

YCH

TLV2