DOWNLOAD Sony KV-DR34M97 Service Manual ↓ Size: 17.82 MB | Pages: 127 in PDF or view online for FREE

– 8 –

Note: Access to the B3 board is possible after removal

of the shiledcase. Remove the shiledcase by
removing 2 screws +BVTP 3x16

2 Two screws
     (+BVTP 3 

× 12)

3 One screw
    (+BVTP 3 

× 12)

3 One screw
    (+BVTP 3 

× 12)

1 One screw
     (+BVTP 4 

× 16)

5 Terminal bracket

4 Two hooks

2 D5 Board

4 B3 Board

3 Two clips

1 Two clips

2 F1 Board

1 Two hooks

2 BC1 Board

4 V2 Board

(not used for this model)

6 P Board 

1 One clip

3 Two clips

5 One clip

Note: 1) Remove the Rear Cover (refer 1-1)

- unscrew all 14 screws fixed on the Rear Cover. Hold

the top of the TV Cabinet; lift the Rear Cover slightly
upwards to release the Rear Cover foot from the TV
Stand and slide it backwards from the TV Cabinet.

2) Remove the 3D Speaker Box (refer 1-2)
3) Release the Lead Assy Speaker (left side)
4) Lift up the chassis and place it in the Service

Position as shown:-

Place the front of the main
bracket on to the foot of the
TV Cabinet

Use a non elastic and non
conductive string to tie the
main bracket to the woofer
bracket

Place the Terminal
Bracket edge into the hole
on the TV Stand foot

Caution: 1) In Service Position, make

sure all the TV connections
are connected correctly
before turning on the TV
set.

2) The TV on the TV Stand

without Rear Cover is
unstable. As such be
careful not to push the TV
foward or backward

– 9 –

$ Band, DGC(1) Removal (only top-side)

5 Anode Cap Removal

) Earth Coating Assy(2) Removal

7 Loosen the Neck Assembly 
 

fixing screw and remove

9 Loosen the Deflection Yoke
 

fixing screw and remove

6 C Board Removal

! Chassis Assy Removal

8 VM Board Removal

( Spring Tension(2) 
 Removal

# Supports, CRT(2) Removal

& DGC(2) Removal

% Holder, DGC(2) Removal

~ Nut, Locking (4)  

+ Nut special CRT (4)  

" Bracket Woofer(2) Removal

• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom

right and left.

• When removing the Nut Locking: first make sure to hold the Nut special CRT with a spanner while opening the Nut

Locking using a torque driver. Then proceed to remove the Nut special CRT using a torque driver.

1) Place the TV set with the CRT face down on a cushion (jig).
2) Removal the Rear Cover.
3) Removal the 3D Box.
4) Unplug all interconnecting leads from the Deflection Yoke, Neck Assy, Degaussing Coils and CRT grounding strap.

5 One screw
    (3 

× 12)(+)(BVTP)

2 Three screws
    (3 

× 12)(+) BVTP

3 Four hooks

5 One screw
    (3 

× 12)(+)(BVTP)

1 Five connectors

6 Four hooks

7 D Board

4 A Board

3 Three hooks

1 Five hooks

4 Cover, H

2 H1 Board

5 H2 Board

– 10 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

a.

2 Using a thumb pull up the rubber cap firmly in the direc-

b.

3 When one side of the rubber cap is separated from the

c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

a

a

b

b

c

 Anode Button

– 11 –

REF NO.

DESCRIPTION

QUANTITY

PART NO.               REMARK

J-1

TOOL(20P),SERVICE

1

3-702-763-01         For A to BC1 board extension

1

                              For A to P board extension

J-2

TOOL(40P),SERVICE

1

3-702-764-01         For A to B3 board extension

J-3

TOOL(50P-A),SERVICE

1

3-702-765-01         For D to D5 board extension

J-4

TOOL(7PX2),SERVICE

1

3-702-775-01         For  A  to  V2  board extension

                              (not used for this model)

D Board

D5 Board

B3 Board

J Board

P Board

A Board

F1 Board

BC1 Board

V2 Board (not used for this model)

H1 Board

VM Board

H2 Board

C Board

DH Board