DOWNLOAD Sony KV-DB29M60 Service Manual ↓ Size: 6.88 MB | Pages: 123 in PDF or view online for FREE

– 10 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position Neck Assy as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

Purity control

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.

Neck assy
(For 34")

Neck assy
(For 29" and 32")

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

– 11 –

Moved RV9001 (H.STAT)

Preparation:
• Before starting, perform FOCUS adjustment.
• Receive dot/cross hatch pattern.
• Picture Mode "CUSTOM" (PIC 90%, BRT 50%,

COL 50%, HUE 50%, SHP 50%).

1. (Moving vertically), adjust the 4 pole magnet to converge

red, green and blue dots in the center of the screen.

2. Tilt the 4 pole magnet and adjust static convergence to

open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves as
shown below:-

b) Horizontal Static Convergence
If the blue dots does not converge with the red and green
dots, use the 6 pole magnet to adjust in the manner
described below:-

1. Receive cross hatch signal.
2. Set Picture to "MINIMUM", Brightness to

"STANDARD".

3. Adjust the Y separation axis correction magnet on the

Neck Assembly so that the horizontal lines at the top
and bottom of the screen are straight.

Center dot

R    G    B

R

G

B

4 pole

magnet

RV9001

4-pole

Y magnet

C1 Board

R

R

G

G

B

B

A

A

B

B

B

B

R

G

G

R

B

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

Neck assy

Neck assy

Red

Red

VM1 Board

VM1 Board

Blue

Red

Blue

Blue

Purity

6 Pole Magnet

4 Pole Magnet

DY pocket

6 Pole

Magnet

4 Pole

Magnet

– 12 –

Preparation:
• Before starting this adjustment, adjust the horizontal and

vertical static convergence.

Input cross hatch pattern.
i)

TLH
Adjust the horizontal convergence of red and blue dots
by inserting TLH Correction Plate to the DY pocket (left
or right).

ii) YCH

Adjust YCH to balance Y axis.

iii) TLV

Adjust the vertical convergence of red and blue dots.

iv) XCV

Adjust XCV to balance X-axis

Affix a Piece B(120), Convergence Correct/Permaloy
Assy Correction to the misconverged areas.

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

TLV

DY pocket

TLH Plate

H-TRAP

YCH

XCV

b

a

c

d

a-d : screen-corner
        misconvergence

a

b

c

d

Permalloy assembly

Fix a Permaloy Assy Correction to the misconverged

a to d: Piece B(120), Convergence Correct

or

Permaloy Assy Correction

– 13 –

FOCUS adjustment should be completed before White
Balance adjustment.

1. Receive digital monoscope pattern.
2. Set Picture Mode to "STANDARD".
3. Adjust focus VR so that the center of the screen

becomes just focus.

4. Change the receiving signal to white pattern and blue

back.

5. Confirm magenta ring is not noticeable. In case magenta

ring is obvious, then adjust FOCUS VR to balance
magenta ring and FOCUS.

1. Set the  following condition:

- Picture and Brightness to "STANDARD".
- TV to Video mode.

2. Connect R,G,B of the  C board cathode to oscilloscope.
3. Adjust Brightness to obtain the cathode value to the

value stated below.

4. Adjust SCREEN VR [RV9001] on the FBT until the

scanning line disappears.

1. Set TV to RF Mode.
2. Input PAL monoscope to RF mode (OTHER model) and

NTSC monoscope (NTSC model).

3. Set the following condition:

i) Set "PICTURE MODE" to "CUSTOM" and adjust

PICTURE to 0% and BRIGHTNESS to 50%.

ii) Receive RF PAL monoscope signal

(RF NTSC monoscope: NTSC models)

iii) Adjust Sub BRT (service item COLR 008 SBRT)

to make 10 IRE Slightly glimmer.

iv) Apply the offset steps according to TV size as in Sub

Brightness offset table

Preset constant

Sub Brightness offset

1. Set to Service Mode.
2. Input white raster signal using signal generator.
3. Set the following condition:

i) Receive 100 IRE PAL white signal.
ii) Set to "VIVID" mode.

SADJ 003 COL 60 

➔ 00

iii) Adjust White Balance

COLR

003

GDRV

004

BDRV

006

GCUT

007

BCUT

4) i) Receive PAL ALL White signal (10 uit)

ii) Set to "VIVID" mode

SADJ 003 COL 00 

➔ 100

iii) Adjust color offset

MCP

010

CBOF

011

CROF

Inch

R/G

B/G

34"

0.745

0.905

32"

0.775

0.915

29"

0.790

0.903

Inch

Offset

34"

Adjusted + 3 Steps

32"

Adjusted + 3 Steps

29"

Adjusted + 6 Steps

Cathode setting voltage:
170 V 

± 2 (VDC)