DOWNLOAD Sony KV-DB29M60 Service Manual ↓ Size: 6.88 MB | Pages: 123 in PDF or view online for FREE

– 9 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting or factory setting (shipping condition)

The following is to show on how to access to the "RESET" Function:-

User selection = press 'WEGA GATE' t selectt 'SETTING' t go to 'SETUP' page t select 'FACTORY

SETTINGS' t select 'YES'

Sequential to the resetting operation, TV set would shut down once and automatically turn on again. The power-off
duration is expected to be about 500msec. Initial Setup Menu is displayed.
As a result, some items will be reset to their initial conditions (shipment condition) wheareas some others remain
at the last user selection.

Items that remain at the last user selection

Reset Items

Video input

RF user last setting

Main Volume

25

DRC-MF

DRC1250

Picture mode

VIVID

3D Intelligent Picture

ON

Sound mode

DYNAMIC

Intelligent volume

OFF

Surround

OFF

Wide mode

4.3

Auto wide

ON

Twin

OFF

Program Index

OFF

* Program Block

Reset particular, displayed
channel to unblock

WEGA Theatre Setup

Direct Input

HD/DVD 1

Speaker

Main

Game mode

OFF (Video) *Not available in RF
mode

*= Will reset only if watched/displayed during RESET operation

- For Multi model only

Category

Default

Category

Default

Program No., PICTURE POSITION (included PICTURE

ROTATION and PICTURE V-POSITION), OSD Language, Fine tuning,

TV System, Skip, Program label, Program sorting, Video label.

* Color System

RF = Reset to Auto at the particular/displayed Video
= MI Reset to Auto CH, others keep user setting

Eco mode

OFF

Wide mode

Wide zoom

Auto wide

ON

4.3 Default

Wide zoom

V Center

00

V Size

00

Mute

OFF

OSD Display status

OFF

Center-in volume

25

Initial setup menu

Reactivate/ON

Twin size

Center

– 10 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position Neck Assy as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

Purity control

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.

Neck assy
(For 34")

Neck assy
(For 29" and 32")

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

– 11 –

Moved RV9001 (H.STAT)

Preparation:
• Before starting, perform FOCUS adjustment.
• Receive dot/cross hatch pattern.
• Picture Mode "CUSTOM" (PIC 90%, BRT 50%,

COL 50%, HUE 50%, SHP 50%).

1. (Moving vertically), adjust the 4 pole magnet to converge

red, green and blue dots in the center of the screen.

2. Tilt the 4 pole magnet and adjust static convergence to

open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves as
shown below:-

b) Horizontal Static Convergence
If the blue dots does not converge with the red and green
dots, use the 6 pole magnet to adjust in the manner
described below:-

1. Receive cross hatch signal.
2. Set Picture to "MINIMUM", Brightness to

"STANDARD".

3. Adjust the Y separation axis correction magnet on the

Neck Assembly so that the horizontal lines at the top
and bottom of the screen are straight.

Center dot

R    G    B

R

G

B

4 pole

magnet

RV9001

4-pole

Y magnet

C1 Board

R

R

G

G

B

B

A

A

B

B

B

B

R

G

G

R

B

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

Neck assy

Neck assy

Red

Red

VM1 Board

VM1 Board

Blue

Red

Blue

Blue

Purity

6 Pole Magnet

4 Pole Magnet

DY pocket

6 Pole

Magnet

4 Pole

Magnet

– 12 –

Preparation:
• Before starting this adjustment, adjust the horizontal and

vertical static convergence.

Input cross hatch pattern.
i)

TLH
Adjust the horizontal convergence of red and blue dots
by inserting TLH Correction Plate to the DY pocket (left
or right).

ii) YCH

Adjust YCH to balance Y axis.

iii) TLV

Adjust the vertical convergence of red and blue dots.

iv) XCV

Adjust XCV to balance X-axis

Affix a Piece B(120), Convergence Correct/Permaloy
Assy Correction to the misconverged areas.

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

TLV

DY pocket

TLH Plate

H-TRAP

YCH

XCV

b

a

c

d

a-d : screen-corner
        misconvergence

a

b

c

d

Permalloy assembly

Fix a Permaloy Assy Correction to the misconverged

a to d: Piece B(120), Convergence Correct

or

Permaloy Assy Correction