DOWNLOAD Sony KV-DB29M60 Service Manual ↓ Size: 6.88 MB | Pages: 123 in PDF or view online for FREE

– 7 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or

carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direction

indicated by the arrow b.

3 When one side of the rubber cap is separated from the

anode button,  the anode-cap can be removed by turning
up the rubber cap and pulling it up in the direction of the
arrow c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with sharp

2 Do not press the rubber too hard so as not to damage

3 Do not turn the foot of rubber over too hard.

• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom right

and left.

1) Remove the Rear Cover.
2) Unplug all interconnecting leads from the Deflection Yoke, Neck Assy, Degaussing Coils and CRT grounding strap. Remove

Chassis Assy.

3) Place the TV set with the CRT face down on a cushion (jig).

a

a

b

b

c

 Anode Button

qa

 Earth Coating Assy

4 Anode Cap Removal

8 Band, DGC Removal

9

 Holder, DGC Removal (x2)

qd

 Supports, CRT Removal (x2)

qs

 Spring Tension Removal (x2)

qf

 Screw Tapping 7+ Crown Washer

q;

 Degaussing Coil

6 Loosen the Neck Assembly
 

fixing screw and remove

 

Neck Assy & VM1 Board

7

 Loosen the Deflection Yoke

  fixing screw and remove

5 C1 Board Removal

– 8 –

REF NO.

DESCRIPTION

QUANTITY

PART NO.               REMARK

J-3

TOOL(50P-A),SERVICE

1

3-702-765-01         For A1 to BH1 board extension

D Board

C1 Board

F1 Board

H1 Board

VM1 Board

DL1 Board

BH1 Board

A1 Board

H2 Board

– 9 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting or factory setting (shipping condition)

The following is to show on how to access to the "RESET" Function:-

User selection = press 'WEGA GATE' t selectt 'SETTING' t go to 'SETUP' page t select 'FACTORY

SETTINGS' t select 'YES'

Sequential to the resetting operation, TV set would shut down once and automatically turn on again. The power-off
duration is expected to be about 500msec. Initial Setup Menu is displayed.
As a result, some items will be reset to their initial conditions (shipment condition) wheareas some others remain
at the last user selection.

Items that remain at the last user selection

Reset Items

Video input

RF user last setting

Main Volume

25

DRC-MF

DRC1250

Picture mode

VIVID

3D Intelligent Picture

ON

Sound mode

DYNAMIC

Intelligent volume

OFF

Surround

OFF

Wide mode

4.3

Auto wide

ON

Twin

OFF

Program Index

OFF

* Program Block

Reset particular, displayed
channel to unblock

WEGA Theatre Setup

Direct Input

HD/DVD 1

Speaker

Main

Game mode

OFF (Video) *Not available in RF
mode

*= Will reset only if watched/displayed during RESET operation

- For Multi model only

Category

Default

Category

Default

Program No., PICTURE POSITION (included PICTURE

ROTATION and PICTURE V-POSITION), OSD Language, Fine tuning,

TV System, Skip, Program label, Program sorting, Video label.

* Color System

RF = Reset to Auto at the particular/displayed Video
= MI Reset to Auto CH, others keep user setting

Eco mode

OFF

Wide mode

Wide zoom

Auto wide

ON

4.3 Default

Wide zoom

V Center

00

V Size

00

Mute

OFF

OSD Display status

OFF

Center-in volume

25

Initial setup menu

Reactivate/ON

Twin size

Center

– 10 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position Neck Assy as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

Purity control

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.

Neck assy
(For 34")

Neck assy
(For 29" and 32")

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a