DOWNLOAD Sony KV-DA28M36 Service Manual ↓ Size: 25.99 MB | Pages: 127 in PDF or view online for FREE

– 9 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direc-

tion indicated by the arrow b.

3 When one side of the rubber cap is separated from the

anode button,  the anode-cap can be removed by
turning up the rubber cap and pulling it up in the
direction of the arrow c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

a

a

b

b

c

 Anode Button

– 10 –

REF NO.

DESCRIPTION

QUANTITY

PART NO.               REMARK

J-3

TOOL(50P-A),SERVICE

1

3-702-765-01         For A to BH1 board extension

J-5

TOOL(7P),(8P),SERVICE

1

J-2509-400-D         For A to BC board extension

WL Board

BP Board

BC Board

BH1 Board

J Board

A Board

D Board

F1 Board

VM Board

H2 Board

H1 Board

C Board

DL Board

– 11 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items
will be reset to its original setting (shipping condition)

There are 2 ways to access to the "RESET" Function:-

a) By pressing "RESET" button on the Remote Commander.
b) By pressing "MENU" button on the Front Key Input and hold it down for 5 seconds.

(DAXXMXX doesn't have this function anymore.)
(DAXXNXX, DAXXKXX still have it.)

Sequential to the resetting operation, TV set would shut down once and automatically turn on again. The
power-off duration is expected to be about 500msec. Initial Setup Menu is displayed.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other
remains at the last selection by user.

Items that remains at the last selection by user

Reset Items

Program No., PICTURE POSITION (included PICTURE

ROTATION and PICTURE V-POSITION), OSD Language, Fine

tuning,TV System, Skip, Program label, Program sorting, Video

label, Program block (NTSC model)

Video input

RF user last setting

Volume

25

DRC-MF

DRC1250

Picture mode

DYNAMIC

3D Intelligent Picture

ON

Sound mode

DYNAMIC

Intelligent volume

OFF

Surround

OFF

Wide mode

4.3

Auto wide

ON

Twin

OFF

Program Index

OFF

* Program Block

Reset particular channel to
unblock

WEGA Theatre Setup

Direct Input

Video 1

Speaker

Main

Game mode

OFF (Video) *Not available in RF
mode

Color System

Reset to Auto at the CH, others
keep user setting

Eco mode

OFF

Wide mode

Wide zoom

Auto wide

ON

4.3 Default

Wide zoom

V Center

00

V Size

00

Picture mode

RF user last setting

Mute

OFF

OSD Display status

OFF

Main volume

25

Center-in volume

25

(Remote button)
Center speaker

Main or center in (No menu display)

(UNDER WEGA

(Selected only when WTM turns on)

THEATRE SETUP MENU)
Initial setup menu

Reactivate/ON

Twin size

Center

*= Reset only during watching time

- For Multi model only
- Not reset for NTSC model

Category

Default

Category

Default

– 12 –

• The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

• These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise
noted:
PICTURE control ...........................................................  normal
BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note :  Test Equipment Required.

1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope

Preparation :
• In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

• Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Pic mode : Dynamic

2. Position neck assy as shown in Fig 5-1.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 5-1 through 5-3.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 5-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.
(See Figure 5-4.)

Neck assy

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a