DOWNLOAD Sony KV-BZ213M50 (serv.man2) Service Manual ↓ Size: 18.41 MB | Pages: 127 in PDF or view online for FREE

– 12 –

 

 

 

 

 

 

 

 

 

 

 

Purse Lock

Ø

5

  

90

 

 

 

Purse Lock

Ø

5

Purse Lock Ø5

HV Cable

Lead Assy, G2

Lead Assy

,

G2

Lead Assy

, 

Focus

Earth Assy

,

Keep Lead Assy,

G2

away from HV
cable (at least

1mm/kv)

Keep Lead Assy, G2
away from Heat sink

Rotational Coil

Non-rotational Coil

Keep Lead Assy,

Earth away from heat sinks

Lead Assy, Earth

Conn Assy, 7P

Purse Lock Ø5

UL Wire (1-923-000-81)

Conn Assy, 7P

Rotational Coil

Purse Lock Ø5

Lead Assy, Earth

Keep Lead Assy,

Earth away from heat sinks

UL Wire (1-923-000-81)

Connector Assy, 7P

Lead Assy,

UL Wire

Rotation coil

DY

Wire from

Rotation coil

Rotational Coil

Connector Assy,

Lead Assy

UL Wire

UL Tape

Conn. Assy, 5P (200V)

Purse Lock Ø5

Lead Assy,G2

Earth Assy, coating

Lead Assy, Focus

Lead Assy, Focus & Lead Assy, G2 is pulled straight up

from FBT to Earth Assy, Coating & dressed together with

purse lock Ø5

Use this as a

reference to

dress ECA, Lead

Assy, Focus & G2

TVSR (Clause 9.4.7) :
- Keep HV cables away from
  conductive parts 1mm/KV or more

– 13 –

A

45

o

B

A

A

A

C

 

 

 

 

HV Holder

180 ± 5

Purse Lock

HV Holder Combi

HV Holder Combi

Dress AC Power Cord at PWB Bracket hook as shown

Dress AC Cord Holder at the terminal bracket

PWB Bracket hook

Terminal bracket

AC Cord

AC Power Cord

Purse Lock

DGC

DGC Conn

Black tape

Place purse lock Ø9 after the exit of DGC
Conn from DGC

– 14 –

No need to dress 

Lead Assy, H Static 

at CRT socket's hook.

CRT socket's hook

Make sure wire is not in direct 

contact with heat sink of IC751

Connector Assy, 7P

Dress Connector Assy, 7P 

with pin, wire A705

Dress Connector Assy, 7P 

with cable tie at alignment hole 

A

– 15 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:

Picture control ......................................................... NORMAL
Brightness control ................................................... NORMAL

Perform the adjustments in order as follows:
1. Beam Landing
2. Convergence
3. Focus
4. G2 (SCREEN)
5. White Balance

Note: Test Equipment Required
1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's

picture tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loosen the deflection yoke mounting screw, and set the

purity control to the center as shown below.

3. Set the raster signal of the pattern generator to green.
4. Move the deflection yoke (DY) backward and adjust the

purity control so that green is in the center and blue and
red are at the sides evenly.

5. Then move the DY forward and adjust so that the entire

screen becomes green.

6. Now switch over raster signal to red then blue and

confirm the condition.

...................................................................................................................................................................................................................... ...........

5. Oscilloscope
6. Landing Checker
7. XCV Adjuster

Purity control

Red

Blue

Green

7. When the position of the DY is determined, tighten it

with the DY mounting screw.

8. If the beam does not land correctly in all corners of the

screen, use magnet disc to correct it.

Preparation :
• Before starting, perform FOCUS adjustment.
• Picture mode STANDARD.
• Receive dot/cross hatch pattern.

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

4 pole magnet

RV750
H. STAT

RV1800
G2 (SCREEN) 

Center dot

R     G     B

G

R

B