DOWNLOAD Sony KV-BZ212M10 Service Manual ↓ Size: 8.48 MB | Pages: 80 in PDF or view online for FREE

– 29 –

1. Set TV to Video mode.
2. Set Picture mode to "Custom".
3. Input PAL 100% CB to TV set (OTHERS), NTSC 75%

CB (NTSC model).

4. Set PICT 003 "PWL" to 00h WHBL 017 "BLBG" to 01h.
5. Set the following condition:

PICTURE 100%, COLOR 0%, BRIGHTNESS 50%

6. Connect an oscilloscope to pin 4 (R Output) of CN004.
7. Select SADJ 000 "PMAX" with 1 and 4 button of the

commander then adjust VR with spec with 3 and 6
until reach the spec below:

1.90 ± 0.03 Vp-p = For 21" without VM models

8. Select Wide Mode to "ON" in TV and Video mode and

write "PMAX" data - 8 steps (for models with V-
Compression features only).

9. Then press [MUTING] 

t - to write the data.

10. Select "PWL" and "BLBG" back to initial data.

("PWL": 01h and "BLBG": 00h)

11. Then press [MUTING] 

t - again to write the data.

1. Set TV to Video mode.
2. Set Picture mode to "Custom".
3. Input PAL 100% Color Bar(CB) to TV set (OTHER

MODEL).

4. INPUT NTSC 75% CB to TV set (NTSC MODEL).
5. Set PICT 006 "WTS" to 00h and Intelligent Picture to

"OFF".

6. Set the following condition:

PICTURE 50%, COLOR 50%, BRIGHTNESS 50%, HUE
50%, SHARPNESS 50%.

7. Connect an oscilloscope to pin 2 (B Output) of CN004.
8. Select SADJ 004 "SCOL" with 1 and 4 button of the

commander then adjust with 3 and 6 so that
V

B2

=V

B3

=V

B4

 (for PAL), and V

B1

=V

B4

 (for NTSC) then

write in the data +9 step offset.

9. Then press [MUTING] 

t - to write the data.

10. Set "WTS" back to original data and Intelligent Picture to

"ON".

11. Copy no.9 data to PAL TV & DVD mode (OTHER

MODEL) and NTSC TV & DVD mode (NTSC MODEL).

VR

Black

VB2 = VB3 = VB4 (for PAL)

VB1 = VB4 (for NTSC)

(Difference is within 70mV)

VB1

VB2 VB3 VB4

VB1 VB2 VB3 VB4

1. Set TV to Video mode.
2. Set Picture mode to "Custom".
3. Input NTSC 3.58 CB to TV set.
4. Set the following condition:

PICTURE 50%, COLOR 50%, BRIGHTNESS 50%,
HUE 50%, SHARPNESS 50%.

5. Select service mode and - 9 step offset from SADJ 004

"SCOL" using 1 and 3 button of the remote
commander.

6. Connect oscilloscope to pin 2 (B output) of CN004.
7. Set to service mode and select SADJ 001 "SHUE" with

1 and 4 button then adjust to V

B1

=V

B2

=V

B3

=V

B4

 with

3 and 6 button.

8. Press [MUTING] 

t - to write the data.

9. Select service mode SADJ 004 "SCOL" and +9 step

offset and write the data using [MUTING] 

t -.

10. Select TV channel with 3.58 and repeat item (3) to (7)

and +1 step data offset (NTSC model). (not used for this
model)

11. Press [MUTING] 

t - to write the data.

12. For single system model with NTSC 4.43, select TV

channel with NTSC 4.43 and repeat item (3) to (8).

The highest level of V

B1

, V

B2

, V

B3

, V

B4

must be aligned at the same time.

The ideal difference between

V

B2

 and V

B3

 is within ± 80mV.

13. Once adjustment is completed in Video mode, carry out

adjustment in DVD mode. Set TV to DVD mode. Input
NTSC 3.58 CB to DVD set and perform step 4 to 9 and
11.

1. Set TV to RF mode.
2. Input PAL monoscope to RF mode.
3. Set Brightness 50% and Picture to "MINIMUM".
4. Select WHBL 010 "SBRT" with 1 and 4 button of the

remote commander and adjust its data with 3 and 6
so that cut-off level is 10 IRE, slightly glimmer: 20 IRE.

5. Write into the memory by pressing [MUTING] 

t -.

Geometry adjustment must be done for both color systems
PAL and NTSC.

a) Input Monoscope or Special Color Bar(SPCB) signal

using a pattern generator.

b) Set to Service Mode.
c) Select Category/Functionally Name (as in the service

list) using 1 and 4 button on the remote commander.
Eg. GEOM

d) Raise or Lower the data value using 3 and 6 button.
e) Press [MUTING] 

t - to save the data into memory.

Note 1: Geometry Adjustment must be performed for 4 different

modes: PAL 50Hz NORMAL MODE, PAL 50Hz WIDE
MODE, NTSC 60Hz NORMAL MODE, NTSC 60Hz
WIDE MODE.

VB1

VB2

VB3 VB4

80mV

– 30 –

GEOM 013

Vertical Shift

(VPOS)

GEOM 011

Vertical Amplitude

(VSIZ)

Note: Adjust VSIZ to

12.4

±(SPCB)

11.3

±(PAL Monoscope)

11.5

±(NTSC Monoscope)

GEOM 000

Horizontal Shift

(HPOS)

GEOM 009

EW Trapezoid

(EWTZ)

GEOM 005

EW Width (EW)

(HSIZ)

Note: Adjust HSIZ to

16.4

±(SPCB)

14.6

±(PAL Monoscope)

15.3

±(NTSC Monoscope)

GEOM 002

Horizontal Bow

(HBOW)

GEOM 006

EW Parabola/Width

(EWPW)

(PW)

GEOM 007

EW Upper Corner

(UCOP)

Parabola

GEOM 008

EW Lower Corner

(LCOP)

Parabola

GEOM 001

Horizontal

(HPAR)

Parallelogram

GEOM 012

S-Correction(SC)

(SCOR)

GEOM 003

Vertical Linearity

(VLIN)

GEOM 004

Vertical Scroll

(VSCR)

a) Input PAL signal 50Hz in the Service Mode.
b) Set Wide Mode to "OFF".
c) Perform the below adjustments using the "GENERAL

SETTING" sequence. (refer 3-4-1)

d) Once adjustment is done for PAL 50Hz NORMAL

MODE, set Wide mode to "ON", and copy all PAL 50Hz
NORMAL MODE adjusted data to PAL 50Hz WIDE
MODE except VSCR.

e) Now, perform adjustment for NTSC 60Hz NORMAL

MODE.

f)

Set Wide mode to "OFF".

g) Perform adjustment items listed in the above table using

the "GENERAL SETTING" sequence. (refer 3-4-1).

h) Once adjustment is completed, set Wide mode to "ON"

and copy all NTSC 60Hz NORMAL MODE adjusted data
to NTSC 60Hz WIDE MODE except VSCR.

i)

Upon completing adjustment for all modes, reconfirm
VSIZ and VPOS.

–

 31 

–

VIF SAW

SIF SAW

MAIN

Power

Supply

RF AMP Tuner

TEQE2X904B

AGCin

12C

TV

L(Mono)

Video

L(Mono)

CV/YC

L(Mono)

R

CV/YC

L(Mono)

R

R

R

G/Y

B/P

B

R/P

R

L

R

Fbl(RGBin)

24.576MHz

DVD/RGB

AV3

AV2

AV1

MON OUT

Audio Amp

Buffer

TV 

out

Radio

BPF

Mon

out

AV1

in

AV2

in

CV/YC

L(Mono)

AV3

IN

RGB/

DVD

in

5V

30V

IF

24-5.VIFIN1~2

29~30.SIF1~2

115.DGC RELAY 

114.STBY SW

STBY

3.3V

AC in ~

110-220V

CISPR/

PFC

3.3V

RESET

3.3V

5V

8V

3.3/5V

Relay

8V

AUDIO VCC

HV

DGC

+/-15V

Hout

FBT

L

2ch

Audio Amp

VAR

NVM

Pin out

H-drive

H-out

Rot. cct

V-out

VM

RGB Amp

feedback

10W

R

10W (for KV-BZ212N50/P50)

I

mute

EHT, ABL

Hp

1k

EW, Hd

L, R

V+, V-

RGB

+B

On/Off

stdby

Device 12C

12C

SIRCS

Key buttons

PLL

I/O Port

I/O Port

VIF & SIF

POWER

Color

Decoder

YUV

Processor

Jungle

RGB

DAC

Stereo,

DAP

A
D
C

ONE CHIP

Micro

Text

CC & V-chip

11.Xtalout

10.Xtalin

74~76.YUVout

70-72.VUYin

11

9.

K

E

Y

116.DI-JP/MODE1-EU

103.DI-JP/MODE2-EU/

MON SW

-MONO

126.AGC-MUTE

98, 99. SCL1,SDA1

108, 109.  SCL0,SDA0 

102.BINT

122~3.RED~GREEN LED

77.SCART FBL

78~80.RGB3
34,35 InLs,R5 

51.CY/Y4
52.C2
49-50 InL,R4

120.P3.3(S2)

31.AGCout

33.AVL/2SIF 120.S2

44.Intco-IF

43.IFVO

62,63.HPL, R

48.MON-OUT

36,37.OutL, R

111.S1/VC(GA)

85~87

RGBout

84.lk

65.VM

23. VD+

22. VD-

112.ROT CTRL

113.ROT SW

21.EWD

67.Hout

66.AFC 

32.EHTO

83.ABL

60,61

LSL,R

106.AUDIO MUTE

105.AUDIO STANDBY

58.CVB51/Y1
59,C1 
56, 57InL1,InR1
55.CV/Y2
53,54.InL,R2
70 CX

B-INT

LED

+B line

30V

R

LNA cct

(for KV-BZ212P50 only)

(for KV-BZ212P50 only)

– 32 –

Note:
•

All capacitors are in 

µF unless otherwise noted.

•

All electrolytic capacitors are rated at 50V unless otherwise
noted.

•

All resistors are in ohms.
k

Ω = 1000Ω, MΩ = 1000kΩ

•

Indication of resistance which does not have rating
electrical power is as follows.

Pitch: 5 mm
Rating electrical power 1/4W (CHIP: 1/10W)

•

: nonflammable resistor.

•

: fusible resistor

•

¢

: internal component.

•

: panel designation or adjustment for repair.

•

All variable and adjustable resistors have characteristic curve B
unless otherwise noted.

Ω digital multimeter.

✽

k

Reference information
RESISTOR

: RN

METAL FILM

: RC

SOLID

: FPRD

NONFLAMMABLE CARBON

: FUSE

NONFLAMMABLE FUSIBLE

: RS

NONFLAMMABLE METAL
OXIDE

: RB

NONFLAMMABLE CEMENT

: RW

NONFLAMMABLE
WIREWOUND

: 

✽

ADJUSTMENT RESISTOR

COIL

: LF-8L

MICRO INDUCTOR

CAPACITOR

: TA

TANTALUM

: PS

STYROL

: PP

POLYPROPYLENE

: PT

MYLAR

: MPS

METALIZED POLYESTER

: MPP

METALIZED POLYPROPYLENE

: ALB

BIPOLAR

: ALT

HIGH TEMPERATURE

: ALR

HIGH RIPPLE

! are critical for safety. Replace only with

Note: “A” board schematic diagram is divided into 7 blocks.

Each block is named by its function and block “number”.
eg: Processor (Block 001)
Joint connection between boards can be identified using
the block number followed by the grid's guide.
eg: -<PWR-OFF MUTE
002 : 4E
Meaning: Block 001 joint "PWR-OFF MUTE" is connected
to Block 002 joint "PWR-OFF MUTE" located at grid 4E.

 A Board

 C Board